HALO LA56 Series Instructions

Packaging Contents

A. LED module and connector
Módulo LED y conector
Module à DEL et connecteur

B. #8-32 Self tapping screw (included)
Vis autotaraudeuse no 8-32 (fournie)
Tornillo mecánico #8-32 (incluido)

C. #8-32 Screw (included)
Vis no 8-32 (fournie)
Tornillo #8-32 (incluido)

D. #8-32 Hex Nut (included)
Écrou hexagonal #8-32 (inclus)
Tornillo N.° 8-32 autorroscante (incluido)

E. E26 Edison screw base adapter (For retrofit only - see included retrofit instructions)
Adaptateur pour culot vissé Edison E26 (pour une installation dans le cadre de travaux de modernisation seulement - reportez-vous aux instructions relatives à ce type d'installation)
Adaptador Edison E26 con base enroscable (solamente para adaptación; consulte las instrucciones incluidas para adaptación)

F. Torsion springs (see torsion spring installation method)
Ressorts de torsion (consultez la méthode d'installation du ressort de torsion)
Muelles de torsión (consulte el método de instalación del muelle de torsión)

Items Required (Purchase Separately)

• Screwdriver
• Gloves
• Ladder

Articles Nécessaires (à acheter séparément)

• Tournevis
• Gants
• Échelle

Artículos Necesarios (se compran por separado)

• Destornillador
• Guantes
• Escalera

Important Safety Instructions

When using the product, basic precautions should always be followed, including:

• Heed all warnings, including those below and on the product.
• HALO® recessed luminaires are designed to meet the latest NEC requirements and are certified in full compliance with UL. Check your local electrical code before installation, as it sets wiring standards for your locality.
• Read and follow all instructions.

WARNING

• Risk of Fire: Use MINIMUM 90°C SUPPLY CONDUCTORS. Consult an electrician if uncertain.
• Risk of Electric Shock: Ensure power supply is turned off at the fuse box or circuit breaker before installing or servicing the luminaire.
• Risk of Fire/Electric Shock (LED Retrofit Kit): Installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt. Contact a qualified electrician. Luminaire wiring and electrical parts may be damaged when drilling for installation. Check enclosed wiring and components.
• Install this kit only in luminaires with the construction features shown in the photographs and/or drawings.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

CAUTION

• Edges may be Sharp: Wear gloves while handling.

General Installation Requirements:

• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
• Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system and connection method must comply with the National Electrical Code and local building codes.
• This device complies with Part 15 of the FCC Rules and ISED ICES Standard Canada ICES-005(B) / NMB-005 (B).
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Examine all parts not intended for replacement for damage and replace any damaged parts prior to installation.
• This device is not intended for use with emergency exits.
• For Canada: Complies with CSA C22.2 No. 250.1-16 for luminaire conversion. Combination suitability must be determined by authorities having jurisdiction. Product must be installed by a qualified electrician in accordance with applicable electrical codes. This guide does not supersede local or national regulations.

SAVE THESE INSTRUCTIONS AND WARNINGS.

Non-Screwbase LED Luminaires

WARNING: Risk of Fire/Electric Shock

• LED connector is compatible with Halo 5" E550, H550 Series and 6" E750, H750 and H2750 Series LED Housings.
• LED connector meets California Title-24 high-efficacy luminaire standard as a non-screw base socket.
• LED connector is a non-screwbase luminaire disconnect for tool-less installation.
• The LA56 is UL Certified for use with any 5" or 6" diameter recessed luminaire constructed of steel or aluminum with an internal volume that exceeds 107.9" in³ and does not exceed the input rating of the luminaire.

Compatible HALO® Luminaires:

H7ICAT, H7ICT, H7T, H7ICATNB, H7ICTNB, H7TNB, H7UICAT, H7UICT, H7TCP, H7RICAT, H7RICT, H7RT, H27ICAT, H27ICT, H27T, H27RICAT, H27RICT, H27RT, H5ICAT, H5ICATNB, H5RICAT, H5T, H5TNB, H5RT, H5TM, H25ICAT, H25ICATNB, E27ICAT, E27RICAT, E27RTAT, E27TAT, E7ICAT, E7ICATNB, E7RICAT, E7RTAT, E7TAT, E7TATNB, E5ICAT, E5ICATNB, E5RICAT, E5RTAT, E5TAT, E5TATNB

Compatible HALO® LED Luminaires:

H750ICAT, H750RICAT, H750T, H750TCP, H2750ICAT, H2750RICAT, H550ICAT, H550RICAT, E550ICAT, E550RICAT, E750ICAT, E750RICAT

Compatible HALO® LED Retrofit:

ML7BXRFK, ML7E26RFK

Compatible Juno Luminaires:

IC22, IC22R, IC22W, IC22S, IC23, IC23W, IC21, IC21R, IC2, TC2, TC2R, IC20, IC20R, IC25, IC25R, IC25W, IC25S, TC20, TC20R

Compatible Lightolier Luminaires:

1104ICS, 1104ICR, 1104SIC, 1104SICR, 1004ICS, 1004ICR, 1004SIC, 1004SICR

Compatible Capri Luminaires:

CR1, PR1, QL1, R9ASIC, R5

Compatible Progress Luminaires:

P86TG

Compatible Lithonia Luminaires:

L7X, L7XP

Compatible Thomas Luminaires:

PS1, R9ASIC/PS9RM

Compatible Prescolite Luminaires:

IBXS

Compatible Commercial Electric Luminaires:

C7ICA (H3), H18

Compatible Elco Luminaires:

(HL7ICA) EL7ICA

Compatible Elite Luminaires:

B6ICAT, B6RICAT, B6, B6R, B5ICAT, B5RIACT, B5, B5R

Diagram Descriptions

Figure 1: Ground wire
Shows the green ground wire connection from the LED module to the housing.

Figure 2: Ground wire installation
Illustrates connecting the ground wire using a #8-32 screw into a ceiling thickness adjustment slot.

Figure 3: Ground wire installation
Illustrates connecting the ground wire using a #8 nut.

Figure 4: Ground wire installation
Illustrates connecting the ground wire using a #8-32 screw into an existing hole in the luminaire side wall.

Figure 5: Retrofit Connection
Shows the connection of the RL560 LED module (A) to the Edison base adapter (E).

Figure 6: LED Connection
Shows the connection of the HALO dedicated LED connector (A) to the LED module.

Figure 7: Torsion Spring Installation
Illustrates inserting torsion springs into a 6" luminaire.

Dimming

The Halo LED luminaire can be dimmed with phase-control dimmers (leading edge and trailing edge phase cut). Refer to product specifications and dimming information at www.cooperlighting.com. Consult the dimmer manufacturer for their latest dimmer listings, load ratings, and product information.

Wire Installation

Before proceeding, confirm luminaire compatibility with the RL560 LED SeleCCTable RETROFIT. A list of common luminaires is provided in the Recessed Luminaires section of these instructions.

Ground Wire Installation

For ground connection from the LED module to the housing, use the provided green ground wire (factory installed) as shown in Figure 1 and connect via one of the following methods:

• Use supplied #8-32 screw (Figure 2).
• Use supplied #8 nut (Figure 3).
• Use supplied #8-32 screw into existing hole inside the luminaire (Figure 4).

Note: If no hole exists, drill a small pilot hole and use the provided #8 sheet metal screw.

Retrofit Installation Into E26 Edison Screw Base Recessed Luminaires

1. Remove mounting bracket and plate from inside the existing recessed luminaire (if installed).
2. Remove socket from plate (if installed).
3. Screw Edison base adapter (E) into the existing Edison base socket in the luminaire (Figure 5).
4. Plug the orange connector on RL560 LED module (A) into the orange connector included with the screw base adapter (E) (Figure 6).
5. Bundle any excess length of wire inside the luminaire (above the module) in preparation for insertion.
6. Install the module. (See MOUNTING section for specific instructions).

Installation Into Halo H2750X, H550X And H750X Series LED (Non-Screw Base) Luminaires

1. Plug the orange connector on RL560 LED module (A) into the orange connector included with the luminaire (Figure 6).
2. Bundle any excess length of wire inside the luminaire (above the module) in preparation for insertion.
3. Install the module. (See MOUNTING section for specific instructions).

Mounting

Regardless of the method selected, a round foam gasket has been provided for installation if local code requires.

Torsion Spring Installation Method

1. Properly wire the unit as instructed in the WIRING section of these instructions.
2. If torsion springs are not pre-installed, remove them and screws from the parts bag and install them to the ends of the center bracket as shown in Figure 8.
3. For installation into a 6" luminaire, press each leg of the torsion springs together and insert them through the receivers inside the luminaire (Figure 7).
4. For installation into a 5" luminaire, loosen each screw of the torsion spring bracket, slide them into the 5" position as marked, and retighten the screw. Press each leg of the torsion springs together and insert them through the receivers inside the luminaire (Figure 9).

Note: For easiest installation, insert both sides of the torsion springs simultaneously.

Rewiring or Uninstalling LA56 LED Module

Torsion Spring Method Removal

1. Pull down firmly on the module until it can't continue downwards.
2. Reach between the flange of the module (inside the can) and squeeze the torsion spring legs together to remove them from the luminaire receptors.
3. Disconnect the LED module wiring from the recessed luminaire (LED connector or screw-in Edison base).
4. Remove ground wire from luminaire.

5-Year Limited Warranty

This warranty is exclusive and in lieu of all other warranties, whether express, implied, or statutory, including any warranty of merchantability or fitness for any particular purpose. Cooper Lighting Solutions warrants products to be free from defects in materials and workmanship for five years from the date of purchase. The obligation is limited to replacement products. This warranty extends only to the original purchaser. Proof of purchase is required. The warranty does not apply to products that have been altered, repaired, subjected to neglect, abuse, misuse, accident, or shipping damages. It also does not apply to products not manufactured by Cooper Lighting Solutions. Damage caused by replacement bulbs, corrosion, or discoloration of brass components is not covered.

Limitation of Liability:

Cooper Lighting Solutions shall not be liable for special, indirect, incidental, or consequential damages, nor for lost profits. Liability for any claims arising out of or connected with these terms shall not exceed the purchase price of the product. No labor charges will be accepted to remove or install fixtures. Returned products must have a Return Goods Authorization Number and be returned freight prepaid. Cooper Lighting Solutions is not responsible for merchandise damaged in transit. Any damage in transit should be reported to the carrier immediately.

Reproduction of this document without prior written approval of Cooper Lighting Solutions is strictly prohibited.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.