Defiant DFI-5892-WH Video Motion Security Light

Safety Information

PRECAUTIONS

• Please read and understand this entire manual before attempting to assemble, install, or operate this light fixture.
• This light fixture requires a 120-Volt AC power source.
• Some codes require installation by a qualified electrician.
• This light fixture must be properly grounded.
• This light fixture should be installed outdoors to a wall or eave.
• The light fixture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light fixture is mounted higher than recommended, aiming the sensor down will reduce the coverage area.
• The light fixture/camera requires constant power to operate. Whenever the power is turned on to the light fixture (either for the first time or after a power outage), the light requires a 60-second boot-up period before the camera will be fully operational.

⚠️WARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light fixture.

⚠️WARNING: Risk of fire. Keep the lamp heads at least 2 in. (51 mm) from combustible materials.

❗CAUTION: Burn hazard. Allow the light fixture to cool before touching.

ℹ️NOTICE: Do not connect this light fixture to a dimmer switch or timer.

Many states regulate the use of security cameras and other recording devices. It is the purchaser's sole responsibility to ensure compliance with all applicable laws and to provide any legally required notices. Check local laws regarding the use of any recording devices and cameras prior to installation.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAN ICES-005 (B)/NMB-005 (B)

Warranty

5-YEAR LIMITED WARRANTY

WHAT IS COVERED

This product is guaranteed to be free of factory defective parts and workmanship for a period of 5 years from date of purchase. Purchase receipt is required for all warranty claims.

WHAT IS NOT COVERED

This guarantee does not include repair service, adjustment and calibration due to misuse, abuse or negligence, or LEDs. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components that a customer uses in conjunction with this product.

No service parts available for this product.

Contact the Customer Service Team at 1-844-760-3644 or visit www.homedepot.com.

Pre-Installation

PLANNING INSTALLATION

Before installing the light fixture, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light fixture.

Estimated installation time: 30 minutes

SPECIFICATIONS

TOOLS REQUIRED

• ? Phillips screwdriver
• ? 1/8 in. Flathead screwdriver
• ✂️ Wire strippers/ cutters
• ⚡ Circuit tester
• ? Work gloves
• ? Silicone sealant
• ? Ladder
• ? Safety goggles
• ? Mobile Device

Installation

1. Determining the mounting location

NOTE: The light fixture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light fixture is mounted higher than recommended, aiming the sensor down will reduce the coverage area.

• Determine the mounting location – wall or eave mount.
• Position the lamp heads (A) in the general direction of the desired light coverage.
• If needed, rotate the motion sensor (C) so the text faces upward.

Diagram Description: Shows two mounting options: Wall Mount and Eave Mount. An illustration shows the motion sensor (C) with text indicating it should face upward.

2. Removing the mounting plate

NOTE: This fixture comes with a mounting plate (D). It is pre-assembled on the light fixture (B) for shipping.

NOTE: The small mounting bolt (EE) is pre-installed in the light fixture (B). Do not attempt to remove the small mounting bolt (EE).

• Unscrew the small mounting bolt (EE) connecting the light fixture (B) to the mounting plate (D) and remove the mounting plate (D).

Diagram Description: Shows the light fixture (B) being detached from the mounting plate (D) by unscrewing the bolt (EE).

3. Installing the mounting bracket

⚠️WARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light fixture.

NOTE: Six mounting bracket screws of various sizes are included. The installation will only require two. Discard the unused mounting bracket screws after installation.

• Remove the existing light fixture.
• Install the mounting bracket (FF) with the stamped word "FRONT" facing away from the junction box. Use the mounting bracket screws (BB or CC) that best fit the junction box.
• Firmly pull on the mounting bracket to verify it is securely mounted to the junction box. If necessary, use the screws that were removed from the existing light fixture.

Diagram Description: Shows the mounting bracket (FF) being attached to a junction box using screws (BB or CC). The word "FRONT" on the bracket is oriented away from the box.

4. Installing the mounting plate

• Route the junction box wires through the hole in the mounting plate (D).
• Place the mounting plate (D) against the junction box.
• When mounting to a wall, the "UP" arrow must point upward.
• When mounting to an eave, the "UP" arrow must point toward the building.
• Insert the large mounting bolt (DD) through the mounting plate (D) hole located below the threaded hole, and thread it into the center hole of the mounting bracket (FF). Tighten the bolt (DD) securely.
• Firmly pull on the mounting plate (D) to verify it is securely attached to the mounting bracket (FF).

Diagram Description: Illustrates routing wires through the mounting plate (D), placing it against the junction box, and securing it with the large mounting bolt (DD) into the mounting bracket (FF). Arrows indicate "UP" direction for wall and eave mounts.

5. Making the electrical connections

• Insert the junction box wires into the side of the terminal block and around the ground screw. Tighten terminal block screws using the mini-screwdriver (GG) and ground screw to secure the wires.
• Insert the white wire from the junction box into the terminal marked "N (White)".
• Insert the black wire from the junction box into the terminal marked "L (Black)".
• Connect the bare or green ground wire from the junction box to the ground screw (marked with "GND").

Diagram Description: Shows the wiring connections to the terminal block. Wires are connected to terminals labeled N (White), L (Black), and GND.

6. Mounting the light fixture

NOTICE: The two pins on the rear of the light fixture must be inserted into the terminal block for the light to work.

• Align the bottom edge of the light fixture (B) with the bottom edge of the mounting plate (D). Tilt the light fixture (B) toward the mounting plate (D), making sure the light fixture (B) is centered on the mounting plate (D).
• Tighten the small mounting bolt (EE) securely through the center of the mounting plate (D). Do not overtighten.
• Push the rubber plug (AA) firmly into the mounting bolt hole on the light fixture (B).

Diagram Description: Shows the light fixture (B) being attached to the mounting plate (D) with the bolt (EE) and the rubber plug (AA) being inserted.

7. Caulking around the light fixture

• Caulk around the mounting plate (D) and mounting surface with silicone sealant (not included).

Operation

1. Adjusting the lamp heads

⚠️WARNING: Risk of fire. Keep the lamp heads at least 2 in. (51 mm) from combustible materials.

❗CAUTION: Keep lamp heads 30° below horizontal to avoid water damage and electrical shock.

• Turn the power on at the circuit breaker or fuse and turn on the wall switch.
• If needed, gently grasp the lamp heads (A) and tilt them up or down or side to side to adjust the light coverage area.

Diagram Description: Shows arrows indicating the lamp heads (A) can be tilted up, down, left, or right.

2. Rotating the sensor controls downward

• Rotate the motion sensor (C) so the text faces upward.

NOTICE: All clearances must be maintained. See Safety Information on page 2.

NOTICE: The Notifi™ mobile app must be downloaded to operate the light fixture. See Step 3 on page 9 for instructions.

Diagram Description: Shows the motion sensor (C) with an arrow indicating rotation to face upward.

3. Downloading the mobile app

• Download the Notifi™ mobile app. Search for the "Notifi Video Solutions" app.
• iOS Devices – Download the app from the App Store℠.
• Android Devices – Download the app from the Google Play™ store.

4. Connecting the light to the mobile app

NOTICE: The network password will be required to complete this process.

• Ensure the power to the light is turned ON. Allow 60 seconds for system boot-up.
• On the mobile device, go to Settings > Wi-Fi and select "Notifi_Video_SecurityXXXX" ("XXXX" represents the unique MAC address of each light fixture) from the available Wi-Fi networks.
• Once connected, open the Notifi app. The app will detect the new light.
• Select "Yes" to start the setup and the app will guide you through the remaining steps.

NOTE: When creating a new Notifi account, the username and password must be a minimum of 4 characters and a maximum of 12 characters. Alpha-numeric and/or special characters may be used.

5. Viewing live video

The Notifi app provides live-stream video from the camera to a mobile device.

• Tap the name of the camera to be viewed.
• While in the live-stream screen, the following options are available:
• Tap the video camera icon (▶️) to start recording live video. Tap again to stop recording.
• Tap the camera icon (?) to save a still image from the live-stream video.
• To return to the main app screen, tap the (X) or "Back" button in the top left corner.

NOTE: All videos and images will be saved to the mobile device currently being used to view the live-stream video.

6. Understanding the motion detection process

This light has dual motion detection technologies.

• The light is controlled by a 180° PIR (passive infra-red) sensor. This sensor detects a temperature difference moving in front of it. When motion is detected after dark, the light will come on at the selected "Full Bright Intensity" level.
• The camera uses both the 180° PIR sensor as well as a 100° image sensor located within the camera software. The camera's image sensor will not activate unless the PIR sensor first detects a moving temperature difference within the detection zone. The camera will record motion day or night.

7. Using the event list

• Tap the Events tab.
• An event is created each time the camera senses motion.
• Basic Service – The event list will show the date and time the motion was detected.
• Premium Service (available for an additional fee) – The event list will include the date, time, and video of the event each time motion was detected. The video of each event will also be available to download for 30 days.

8. Receiving notifications

• Tap > Feature Settings > Notifications to select the notification settings.
• If notifications are turned on, an email and/or push notification is sent each time the camera senses motion. Tap on the notification to be taken to the live-view video screen (Basic service) or the Event video (Premium service).

9. Adjusting the light settings

The light settings allow you to adjust the full bright duration, the DualBrite® duration, and the percentages of light intensity.

NOTE: Changes made to one light's settings will not affect another light's settings.

• Tap > Feature Settings > Light to select the light settings.
• Full Bright Duration – This adjusts the amount of time the light will stay ON after all motion has stopped.
• DualBrite Duration – This adjusts the amount of time the light stays ON at a reduced brightness level when no motion is detected.
• Full Bright Intensity – This adjusts the intensity level of the light when motion is detected.
• DualBrite Dimming Level – This adjusts the intensity level of the light when no motion is detected.

10. Adjusting the camera settings

The camera settings allow you to adjust the motion detection sensitivity, motion detection zones, and video quality.

NOTE: Changes made to one camera's settings will not affect another camera's settings.

NOTE: The higher the "Sensitivity" setting, the greater the possibility of false triggering. To reduce false triggering, select a lower setting.

• Tap > Feature Settings > Camera to select the camera settings.
• Motion Detection – This adjusts the camera's sensitivity to motion in its field of view.
• Motion Detection Zones – This adjusts the camera's detection area to include or exclude zones in its field of view.
• Auto Adjust - Disabling this setting allows manual adjustments of the video's quality settings. For best performance, leave the Auto Adjust ON.

11. Setting the sensor for testing

NOTE: The light fixture will operate during the day or night during testing. The light will stay on for 5 seconds after all motion is stopped.

NOTE: The light requires a 60-second boot-up period before the camera will be fully operational.

• Tap > Feature Settings > Camera > Motion Detection to select the motion detection settings.
• The light fixture will automatically enter "Test" mode whenever the "Motion Detection" option is selected. The light fixture will remain in "Test" until one of the following actions occurs:
• The "Save" or "Cancel" option is selected.
• No movement during the testing process for 30 seconds.
• Three minutes have passed without changing one of the on-screen settings.

12. Adjusting the motion sensor detection zone

NOTE: The camera's (E) detection zone is inside of the light's detection zone. When the motion sensor (C) for the light is adjusted, the camera's (E) motion sensor will also be adjusted.

If motion is detected outside the camera's detection zone, the light may turn on but the camera will not record an event.

• Perform a "walk test": walk in an arc across the front of the motion sensor (C).
• Watch the light. The light will come on and the red LED will flash indicating motion has been detected.
• Stop, wait for the light to turn off, and then begin walking again.
• Continue this process until the detection zone has been established.
• If needed, gently grasp the motion sensor (C) and move it from side to side or up and down to adjust the detection zone.
• Adjust the "Motion Detection" sensitivity to High, Medium, or Low as needed.

NOTE: The motion sensor (C) is more sensitive to motion moving across the front of the sensor. The motion sensor (C) is less sensitive to motion moving directly toward the front of the sensor.

Diagram Description: Shows a top-down view of the motion sensor's detection pattern, illustrating sensitivity to side-to-side motion versus direct approach.

13. Adding multiple users

The Notifi system allows control of multiple users within an account.

• Tap > Advanced Settings > Manage Multiple Users.
• Tap the "Add Viewers" button and type the email address in the "To:" field.
• Tap the "Send" button.

NOTE: When adding multiple users, separate the email addresses with a semicolon.

14. Adding system name and photo

Add a name and photo to represent the Notifi system on the mobile device. The photo will be placed inside the blue circle icon next to the selected Notifi system.

• Tap > Advanced Settings > System Name/Photo.
• Enter a name for the Notifi system.
• Select an existing photo and take a new photo to represent the Notifi system.

NOTE: The light settings and name are stored in the light fixture. The photo is locally stored on the mobile device and is only visible on that device.

15. Using manual mode

Manual mode overrides the motion sensor (C) and will turn the light on at the preset "Full Bright Intensity" level. This feature works day or night. The motion sensor (C) will reset to motion sensing mode at sunrise.

• On the main screen under the "Systems" tab, choose "ON", "OFF", or "AUTO" to control the lights for the selected Notifi system.

16. Deleting a Notifi system

To delete a Notifi system from an account:

• Turn off the wall switch controlling the Notifi system.
• On the main "Systems" screen, wait for the system to go offline (the system name and image will turn gray).
• Once offline, swipe the Notifi system to be deleted to the left and tap the trashcan icon (?️).

Care and Cleaning

• To prolong the original appearance, clean the light fixture with clear water and a soft, damp cloth only.
• Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish. This is not a defect in the finish and will not be covered by the warranty.
• Do not spray the light fixture with a hose or power washer.
• To clean the camera lens, use a dry, microfiber cloth only.

Troubleshooting