LEXON Luma M LH87 User Manual

Introduction

This document provides comprehensive instructions for the LEXON Luma M LH87 lamp, designed by Manuela Simonelli & Andrea Quaglio. It covers unboxing, setup, operation, multi-lamp networking, safety precautions, and technical specifications.

In the Box

• 1x Luma M lamp
• 1x USB Type-C charging cable ?
• 1x User manual

Product Overview

The Luma M lamp features:

1. Touch area (Lighting function)
2. Lamp body
3. BT Button ? (connection between Luma M lamps)
4. Reset key
5. Receiver for wireless charging
6. LED indicator (battery & charging status) ?
7. USB Type-C charging port ?

Charging

It is recommended to fully charge the battery before first use. Initial full charge takes approximately 3 hours via USB charging and 4 hours via wireless charging.

Operating Instructions

Setting up one Luma M lamp

• Touch the top of the lamp to turn it ON.
• There are 9 color options selectable by touching the top.
• To adjust brightness, touch and hold the top area until the desired brightness is reached, then release.
• To turn OFF the light, wait 3 seconds after color selection, then touch again. The last color setting is remembered.

Pairing several Luma M lamps (Interconnection network)

Pairing Luma M lamps requires no third-party software. To synchronize multiple lamps:

1. Press and hold the BT button ? on each lamp for 3 seconds to enable the communication module. The Blue LED will flash.
2. Select one lamp and press the BT button ? twice to initiate multi-pairing. Once complete, all lamps will share the same color setting. The lamp used for connection becomes the MASTER, identified by a continuously flashing LED, while others are SLAVES (LEDs off).

Once paired, you can control color, brightness, and ON/OFF for all lamps from any single lamp.

Add one or more Luma M lamps to the network

1. Turn ON new Luma M lamps by pressing and holding the BT button ? on each unit for 3 seconds.
2. Press the pairing button once on any lamp already in the network (repeat for each new device).

Exclusive LOCK NETWORK Feature

Luma M features a unique locking system where only one lamp (MASTER) controls the network, preventing changes from other lamps (SLAVES). To enable LOCK function:

1. On the MASTER device, press the BT button ? 5 times. This sends a signal to ALL other lamps to LOCK.
2. In LOCK mode, only the MASTER interacts with other lamps. Its LED flashes twice every 3 seconds.
3. To unlock the network, quickly press the BT button ? on the MASTER lamp 5 times.

Safety Precautions

• The device is [IPX4] water resistant, protecting against rain, splashes, and spray water. Do not immerse in water to avoid internal damage.
• Avoid extreme hot or cold temperatures; use at room temperature.
• Do not attempt to service, repair, or disassemble the device yourself.
• Use only certified wireless chargers.
• Ensure charging specifications are met (DC Input: 5V). Never use an adapter with a higher output voltage.
• Do not place the Luma M case on a wireless charger with conductive materials (metal, magnets) between the case and charger.

Product Specifications

Compliance Information

European Union CE Directive: LEXON declares that this device complies with the essential requirements and other relevant provisions of the RED Directive 2014/53/EU. The original EU declaration of conformity can be found at: https://www.lexon-design.com/assets/certifications-ce-lumam.pdf

UK Conformity Assessment: This device conforms to the essential requirements and relevant provisions of the UK Radio Equipment Regulations 2017 (SI 2017/1206). The original UK declaration of conformity can be found at: https://www.lexon-design.com/assets/certifications-ukca-lumam.pdf

RF Specification: Bluetooth ?: 2402-2480 MHz. WPT: 110 kHz-148 kHz (RX). BT transmitter power: 2.34dbm.

Disposal and Recycling Information: Electrical and electronic devices must not be disposed of with domestic waste. Consumers are obliged to return old devices to designated public collection points or points of sale. This symbol [Recycle] indicates compliance with these regulations.

USA - FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the responsible party could void the user's authority to operate the equipment. This equipment generates, uses, and can radiate radio frequency energy. RF exposure compliance is met.

Canadian Compliance Statement: This device complies with Industry Canada license-exempt RSSs. Operation is subject to two conditions: 1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. RF exposure compliance is met.