Menuett 003-284 Steam Cleaner

Safety Instructions

This steam cleaner can be used by children from eight years and upwards and by persons with reduced physical, sensory or mental capabilities, or persons lacking experience or knowledge, provided they are supervised or have received instructions concerning safe use and understand the associated risks. Do not allow children to play with the steam cleaner. Cleaning and maintenance must not be carried out by children unless they are older than eight years and are supervised.

• Keep the steam cleaner and its power cord out of the reach of children under eight years of age.
• Keep children under supervision to ensure they do not play with the steam cleaner.
• Do not expose the power cord or plug to water or other liquids – risk of electric shock.
• Check that the power cord and plug are intact and undamaged. Do not use the steam cleaner if the power cord or plug is damaged. If damaged, it must be replaced by qualified personnel.
• The steam cleaner is intended for household use only, not industrial use.
• Do not start the steam cleaner without water in the reservoir.
• Check that the mains voltage corresponds to the rated voltage on the type plate.
• During use, the reservoir opening must be sealed and the safety cap properly tightened.
• The steam cleaner must only be connected to an earthed power point.
• Any extension cord must be earthed and double insulated.
• Do not tilt the steam cleaner more than 45 degrees during use, as this risks spraying boiling water with the steam.
• Do not point the nozzle at people, animals, or electrical equipment.
• Pull out the plug before filling with water. Always unplug the plug after use and before cleaning and repairs.
• Do not pour rust remover, odour remover, alcohol, or detergent into the reservoir, as this can damage it.
• Do not use the steam cleaner for cleaning swimming pools or similar.
• Do not point the jet at equipment containing electrical components, such as the inside of an oven.
• Do not overfill the reservoir – risk of overpressure.
• Never leave the steam cleaner unattended when it is connected to the mains.
• Do not use the steam cleaner if it has been dropped, is visibly damaged, or is leaking.
• Symbols: ⚠️ Warning: Risk of scalding, ⚠️ Warning: Hot surface.

Technical Data

Intended Use

The steam cleaner can be used for cleaning doors, windows, floors, and clothes.

Product Description and Accessories

The steam cleaner unit comes with various accessories for different cleaning tasks. Ensure all parts are present and undamaged upon unpacking.

Main Unit Components:

• 8. Steam button: Activates steam output.
• 9. Power switch: Turns the unit on/off.
• 10. Status light: Indicates when the unit is ready.
• 7. Lid/Safety Cap: Seals the water reservoir.

Accessories:

• 1. Window cleaner attachment
• 2. Cleaning cloth for textile cleaning
• 3. Textile nozzle
• 4. Funnel: For filling the water reservoir.
• 5. Measuring cup: For measuring water.
• 6. Connector for nozzle: Attaches to the main unit.
• 11. Nozzle for extension tube
• 12. Extension tubes (x3): To extend reach.
• 13. Floor nozzle with microfibre cloth
• 15. Jet nozzle: For concentrated steam.
• 16. Angle nozzle: For reaching tight spots.
• 17. Brush nozzle: For scrubbing.
• 19. Flexible nozzle: For maneuverability.

Diagrams (FIG. 1, 2, 3, 4, 5, 6) illustrate assembly and accessory fitting.

Assembly and Fitting Accessories

General Assembly: Unpack the steam cleaner and check all accessories for damage.

Extension Tubes: Connect extension tubes together or to the floor nozzle by aligning the catches and pushing them into place. To release, press the catches and pull apart.

Connecting Nozzles: Fit the desired nozzle onto the connector by aligning the pins and twisting clockwise until it clicks. To remove, twist anticlockwise and pull.

Angle or Brush Nozzle: Press the nozzle onto the jet nozzle or flexible hose. Twist to the desired angle. Remove by pulling straight out.

Window Cleaner: Hook the textile nozzle onto the window cleaner's hooks and click them together.

Operation

Overheating Protection: When the water reservoir is empty, the power supply automatically cuts off to prevent the empty reservoir from overheating. The steam cleaner has a thermostat that maintains steam at 135°C for disinfection and sterilization. The safety valve automatically relieves any overpressure.

Starting the Steam Cleaner:

1. Plug the power cord into an earthed socket.
2. The steam cleaner is ready for use after approximately four minutes.
3. Push the start inhibitor forward, then gently press the steam button and check for steam output from the nozzle.
4. If steam is released, release the steam button and attach the desired accessory.
5. Press the steam button to begin cleaning.

Refilling Water During Use:

1. Pull the plug from the power point.
2. Press the steam button until no more steam is released.
3. Slowly release the safety cap, but keep it in place until steam stops escaping.
4. Place the steam cleaner in a cool place for about five minutes to cool down. Then, remove the safety cap completely.
5. Use the funnel and measuring cup to fill the reservoir with cold or warm water.
6. Replace the safety cap and tighten it firmly.

Cleaning Functions:

Disinfection and Sterilisation:

1. Attach the jet nozzle or flexible nozzle to the connector.
2. Point the nozzle at the surface to be disinfected.
3. Start the steam cleaner as per instructions.

Cleaning Textiles:

1. Attach the textile nozzle to the connector and fit the cleaning cloth.
2. Point the nozzle at hanging garments.
3. Start the steam cleaner as per instructions.
4. Move the brush nozzle up/down and side-to-side to remove stains from clothes.

Cleaning Windows:

1. Attach the window cleaner nozzle to the textile nozzle.
2. Start the steam cleaner as per instructions.
3. Point the nozzle at the window and start the steam cleaner as per instructions.
4. Move the nozzle up/down and side-to-side to remove stains.

Cleaning Floors:

Floor Nozzle:

1. Lift the short sides of the floor nozzle and attach or remove the microfibre cloth.
2. Lower the short sides.
3. Start the steam cleaner as per instructions.
4. Point the nozzle at the floor and press the steam button to remove dirt and stains from floors and corners.

The microfibre cloth can also be used on the brush nozzle for hard surfaces. For carpets, curtains, or delicate textiles, adjust the brush nozzle lever for shorter bristles.

Angle or Brush Nozzle:

1. Mount the angle or round brush nozzle onto the extension nozzle.
2. Start the steam cleaner as per instructions.

After Use

1. Pull out the plug when the steam cleaner is not in use.
2. Press the steam button until no more steam comes out.
3. Slowly release the safety cap, but keep it in place until steam stops escaping.
4. Place the steam cleaner in a cool place for about five minutes to cool down. Then, remove the safety cap completely.
5. Empty the reservoir and wipe the steam cleaner with a dry cloth.
6. Replace the safety cap and tighten it firmly.