HEATED DISPLAY CASE

Acekool Heated Display Case Operation Manual

Thank you for choosing and purchasing an Acekool product. Please carefully read the operation instructions before use for a correct application and satisfactory effect.

Contents

1. General
2. Structure and Parts
3. Safety
4. Preparation and Power Supply
5. Installation and Operation
6. Cleaning and Maintenance
7. Cautions
8. Major Parameters
9. Circuit Diagram

General

1. This instruction manual contains information about the installation, operation, and maintenance of the device and should be consulted as an important source of information and reference guide.

2. Awareness of the safety instructions and instructions for use in this manual will ensure the safe and correct use of the device.

Structure and Parts

Illustration of a heated display case with a curved glass front. Labeled parts include: Shelf, Water Bowl, Glass door, Drawer.

Illustration of a heated display case with a flat glass front. Labeled parts include: Shelf, Glass door, Drawer, Attemperator.

Safety

• The appliance is not to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
• Children should not play with the appliance.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Cleaning and user maintenance shall not be made by children without supervision.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
• Do not use any kind of pressure water jet for cleaning the device.
• To prevent hazards and to ensure optimum efficiency, no modifications or alterations to the device that are not explicitly approved by the manufacturer may be undertaken.
• This device may only be operated in a technically proper and safe condition.
• The device should never be left unattended during operation. Keep children away.
• Preserve this manual safely. When passing on or selling the device to a third party, the manuals must be handed over along with the device.
• Every person using the device must act in accordance with the manuals and under consideration of the safety advice.
• The device is to be used indoors only.
• Any technical interventions, as well as assembly and maintenance, are to be made by qualified customer service only.

Preparation and Power Supply

Exclusive power socket

The power receptacle must have a reliable earth connection.

Illustration showing a power socket with an earth connection symbol.

No share on socket

Never let the device share the common socket with another appliance, otherwise the cable becomes hot and fire might be resulted.

Illustration showing multiple appliances plugged into one socket, with a warning symbol.

Protect cables

Do not break or damage the cables, as this could result in current leakage and fire.

Illustration showing a damaged power cord with a warning symbol.

No water flushing

Do not flush the device surface with water, as this could result in current leakage.

Illustration showing water being sprayed onto an appliance with a warning symbol.

Prevent from flammables and explosive

Do not place any flammable or explosive materials inside the device, such as ether, gasoline, alcohol, or adhesives. Do not place dangerous products near the device.

Illustration showing a power plug near flammable materials with a warning symbol.

Installation and Operation

Installation

• Place the device on an even and safe surface that supports the weight of the device and is not heat sensitive.
• Do not place the device on an inflammable surface (such as table cloth, carpet, etc.).
• Do not position the device near open fireplaces, electric ovens, arc furnaces, electric heaters, or other heat sources.
• Position the device so that the plug is easily accessible.

Operation

• Before first use, clean the inner sides and the shelves/grids with a soft cloth and a mild cleaning agent. Afterwards, dry the device thoroughly.
• Remove the water bowl from the device. The water bowl is installed inside the device. Fill the water bowl with water.
• Connect the device to a single grounded power socket.
• Set the temperature as required for respective foods. The desired temperature can be adjusted in the range between 30°C-90°C.
• The temperature inside the hot display can be read from the front display.
• Put the foods in appropriate containers before placing them inside the hot display and close it using the sliding door.
• Some of the device parts become very hot; always use safety gloves when placing or removing foods.
• The foods are kept warm at the temperature set previously.
• To place or remove foods, you may open the door at the rear side.
• Switch on the inner light when required using the device's light switch.
• Disconnect the device from the power socket when it is not in use.

Cleaning and Maintenance

• Before beginning with repair or cleaning works, ensure the device is disconnected from the power socket and has cooled down.
• Do not use any acid agents and ensure no water ingresses the device.
• To protect yourself from electric shock, never immerse the device, its cables, and the plug in water or other liquids.
• Do not use any kind of pressure water jet for cleaning the device.

Cleaning

• The device should be cleaned regularly.
• Clean the device from the inside and outside with a soft, damp cloth and a mild cleaning agent.
• Clean the shelves/grids and the housing with a soft, damp cloth and a mild cleaning agent.
• Clean the water bowl regularly. Calcification in the water bowl may be removed with common agents or liquids.
• Only use a soft cloth and never use any kind of abrasive agents or pads which could scratch the surface.
• After the cleaning procedure, use a soft and dry cloth to wipe dry and polish the surface.
• Ensure the device has been cleaned properly before storing it in a dry place.

Maintenance

• Check the mains lead from time to time to ensure it is not damaged in any way. Never use the device if the lead is damaged. If the lead is damaged, it must be replaced by a qualified electrician.
• Only a qualified technician should carry out repairs and maintenance of the device. Do not attempt to repair the device yourself.
• Appliances must be disconnected from their power supply during cleaning or maintenance and when replacing parts.

Cautions

• Children should be supervised to ensure that they do not play with the appliance.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.

Major Parameters

Circuit Diagram

Circuit diagram for HW-80/HW-115 models, showing power input (110-120V~ 60Hz), Attemperator Controller (30-90°C), 125°C safety limit, LED light, Indicator light, and Controller (150°C) components.

Circuit diagram for HW-25R/HW-35/HW-45R/HW-50 models, showing power input (110-120V~ 60Hz), Attemperator Controller (30-90°C), 125°C safety limit, LED light, Indicator light, and Controller (150°C) components.

Note

1. The electric circuit diagram and parameters on the product name plate are final ones if they have been changed.
2. The design might be improved without notice.

Disposal Information

Meaning of crossed out wheeled dustbin: Do not dispose of electrical appliances as unsorted municipal waste; use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least free of charge.

Caution Hot Surface

Do not put the food direct contact with the shelf.

Hovering Door Operation Manual

Models: HW-25R/HW-35/HW-45R/HW-50

Opening the Hovering Door

1. Pull the door up.
2. Push the door forward to hover it.

Closing the Hovering Door

1. Pull the door backward.
2. Close the door downward.

Product Information and Certifications

Models: HW-25R/HW-35/HW-45R/HW-50/HW-80/HW-115

Email: support@acekool.vip

Website: https://www.acekool.vip

Made in China

Certifications:

• ETL LISTED, Intertek 5000649, CONFORMS TO UL STD. 60335-1 & 60335-2-89, CERTIFIED TO CSA STD. C22.2 NO. 60335-1 & 60335-2-89
• ETL SANITATION LISTED, Intertek 5000649, CONFORMS TO NSF/ANSI STD. 7