GE Appliances: Shop for Home, Kitchen, & Laundry Appliances
Installation Guide for GE Appliances models including: PTD60EBSRWS, PTD60EBSR-BPR, PTD60EBSR BPR 7.4 cu. ft. Capacity Aluminized Alloy Drum Electric Dryer, PTD60EBSR BPR 7.4 cu. ft. Capacity Aluminized Alloy Drum Electric Dryer
GE Profile⢠ENERGY STAR 7.4 cu. ft. Capacity aluminized alloy drum Electric Dryer with Sanitize Cycle and Sensor Dry - PTD60EBSRWS - GE Appliances
File Info : application/pdf, 3 Pages, 516.01KB
DocumentDocumentPTD60EBSR/BPR GE ProfileTM 7.4 cu. ft. Capacity aluminized alloy drum Electric Dryer with Sanitize Cycle and Sensor Dry DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES) ELECTRIC DRYER RATING: 240V 5600W 24A 60Hz 208V 4400W 22A 60Hz 23-1/4 EXHAUST OPTION: 4-way rear, right, left and bottom CIRCUIT REQUIREMENTS: An individual, properly-grounded branch circuit, protected by a 30-amp circuit breaker or a time-delay fuse, is required. NOTE: Dryer wall outlet must be located within 36" of service cord entry and acessible when dryer is mounted in position. INSTALLATION INFORMATION: For complete information, see installation instructions packed with your dryer. Special Installation Requirements ALCOVE OR CLOSET INSTALLATION: - If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back. - The dryer MUST be exhausted to the outside. - Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0" both sides, 0" rear and 1" top. - Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed. - No other fuel-burning appliance shall be installed in the same closet with a gas dryer. BATHROOM OR BEDROOM INSTALLATION: - The dryer MUST be exhausted to the outdoors. - The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers. MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION: - Minimum clearances to combustible surfaces are: 0" both sides; 1" rear DRYER EXHAUSTING INFORMATION: Use metal duct only, vertical and horizontal ducting. For answers to your Monogram, GE CaféTM, GE ProfileTM or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000. 30-1/2 to front panel 31-1/8 to door 28-7/8 to door 28-1/4 to front panel 27 Power Cord 5-1/2 11-3/4 43-7/8 38-1/2 SIDE VIEW 8 3-7/8 1-3/4 3-1/4 5 REAR VIEW POWER CORD LOCATIONS 5 Power Cord Hole BACK VIEW 4-1/2 Listed by Underwriters Laboratories Specification Revised 9/25 PTD60EBSR/BPR GE ProfileTM 7.4 cu. ft. Capacity aluminized alloy drum Electric Dryer with Sanitize Cycle and Sensor Dry FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED WITH YOUR DRYER. DUCTING MATERIALS: For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foiltype) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting. EXHAUST LENGTH CALCULATION: 1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn. 2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow. Dryers must be exhausted to the outside. CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard. Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down. FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE-CARES. DRYER EXHAUSTING INFORMATION-- USE METAL DUCT ONLY VERTICAL AND HORIZONTAL DUCTING BEST PERFORMANCE B A 4 2-1/2 Domestic dryer models Maximum length of 4" dia rigid metal duct Exhaust hood type Number A B of 90° 4" 2-1/2" turns opening opening 0 120 ft. 90 ft. 1 Long Vent 6.1-7.4 cu. ft. capacity electric & gas 2 (GTD33, GTD42, GTD45, 3 GTD65, GTX22, GTX33, GTX42 4 and GTX65) 5 100 ft. 85 ft. 70 ft. 60 ft. 55 ft. 75 ft. 65 ft. 55 ft. 45 ft. 35 ft. For every extra 90° elbow, reduce the allowable vent system length by 10 ft. Two 45° elbows will be treated like one 90° elbow. For the side exhaust installations, add one 90° elbow to the chart. When calculating the total vent system length, you must add all the straight portions and elbows of the system (including the transition duct. Specification Revised 9/25 PTD60EBSR/BPR GE ProfileTM 7.4 cu. ft. Capacity aluminized alloy drum Electric Dryer with Sanitize Cycle and Sensor Dry FEATURES AND BENEFITS Washer Link Wirelessly connects the washer to the dryer, enabling the dryer to automatically set the optimal settings based on the load that was just washed. Wrinkle Care Prevent wrinkles by extending the tumble without heat. Sensor Dry Innovative dual thermistor technology continually monitors temperature and moisture to prevent over-drying and protect your laundry. Sanitize Cycle Reduces 99.8% of bacteria found in laundry. Check Vent Notification Receive a notification when the dryer vent needs to be cleaned, ensuring safe operation and optimal drying performance. 120 ft. Venting Innovative 120 ft. venting enables optimal airflow, enhanced drying ability and flexible installation. Built-In WiFi Powered by SmartHQTM Start, stop and monitor your laundry from anywhere while receiving real-time notifications and updates. Download Additional Cycles Leverage the power of SmartHQTM technology to download additional cycles, such as Warm Up, Active Wear and Casual. My Cycle Streamline your laundry process by saving your favorite dryer settings for future use. Quick Dry Quickly dries a variety of loads for families on the go. Damp Notification Receive a notification when your laundry has reached the ideal dampness to remove from the dryer, so you get wrinkle-free results. Eco Dry This dryer uses less energy and still offers reliable performance, giving you the same high-quality results. ENERGY STAR® qualified Meets or exceeds federal guidelines for energy efficiency for year-round energy and money savings. Model PTD60EBSRWS White with silver backsplash Model PTD60EBPRDG Diamond Gray Listed by Underwriters Laboratories Specification Revised 9/25
 | GE Profile PFD95ESPWGN/PFD95ESPWDS Smart Electric Dryer Specifications Explore the GE Profile 7.8 cu. ft. Smart Front Load Electric Dryer (PFD95ESPWGN/PFD95ESPWDS). Features include Steam Sanitize, SmartHQ connectivity, and 4-way venting. View dimensions, electrical requirements, installation details, and accessories. |
 | GE Profile PFD95GSPWGN/PFD95GSPWDS Smart Gas Dryer: Specifications, Dimensions, and Features Detailed specifications, installation dimensions, features, and benefits for the GE Profile PFD95GSPWGN and PFD95GSPWDS 7.8 cu. ft. capacity smart front load gas dryers with Steam and Sanitize cycles. |
 | GE Profile PFD87ESSVWW Smart Electric Dryer: Dimensions, Features, and Installation Guide Detailed specifications and features for the GE Profile™ 7.8 cu. ft. Smart Front Load Electric Dryer (PFD87ESSVWW/ES(P/M)VRS) with Steam and Sanitize Cycle, including dimensions, installation requirements, accessories, and venting information. |
 | GE Profile PFD95GSPTDS 7.8 cu. ft. Smart Gas Dryer: Features, Specs, and Installation Comprehensive overview of the GE Profile PFD95GSPTDS 7.8 cu. ft. smart front load gas dryer. Details features like Steam Sanitize, SmartHQ, dimensions, electrical requirements, and installation guidelines. |
 | GE Profile Laundry Upgrades: Save Big on Top Load Washer and Dryer Pairs Information on purchasing GE Profile top load laundry pairs and receiving a $100 rebate. Includes a list of eligible washer and dryer models. |
 | GE Profile PFW870SSVWW/SPVRS Washer: Specifications and Installation Detailed specifications and installation information for the GE Profile PFW870SSVWW/SPVRS 5.3 cu. ft. Capacity Smart Front Load ENERGY STAR Washer with UltraFresh™ Vent System+ with OdorBlock™. |
 | GE Profile PFQ97HSPVDS UltraFast Combo Washer/Dryer: Specifications and Features Detailed specifications, dimensions, installation information, features, and accessories for the GE Profile PFQ97HSPVDS 4.8 cu. ft. Ventless Heat Pump Technology Washer/Dryer Combo. |
 | GE Profile PFW950SPTDS Washer & PFD95GSPTDS Dryer - Technical Specifications Detailed technical specifications, dimensions, installation requirements, and features for the GE Profile PFW950SPTDS Smart Front Load Washer and GE Profile PFD95GSPTDS Smart Front Load Gas Dryer. Includes information on ENERGY STAR qualification, SmartHQ features, and installation flexibility. |