GE Profile™ 7.8 cu. ft. Capacity Smart Front Load Electric Dryer with Steam and Sanitize Cycle

Dimensions and Installation Information

Electric Dryer Rating:

• 120V/240V: 5600W, 25A, 60Hz
• 120V/208V: 4300W, 23A, 60Hz

Exhaust Options: 4-way via rear, left, right, and bottom. (Right, left, and bottom venting require Side Vent Kit: GFA28DSVN)

Circuit Requirements: An individual, properly grounded branch circuit, protected by a 30-amp circuit breaker or a time-delay fuse, is required.

Note: Dryer wall outlet must be located within 36" of service cord entry and accessible when dryer is mounted in position.

Installation Information: For complete information, see installation instructions packed with your dryer.

Dimensional Views:

Front View: The dryer has a width of 28 inches (71.2 cm). With leveling legs retracted, the height is 39-3/4 inches (101 cm). With leveling legs fully extended, the height is 40-5/8 inches (103.1 cm).

Side View: The depth of the dryer is 32 inches (81.28 cm). This view is also marked as ADA Compliant.

Back View: Shows the rear of the dryer. The exhaust port is located 6-1/8 inches from the side and 3-5/8 inches from the top. The electrical connection is 1-5/8 inches from the side and 11 inches from the bottom.

Stacked Configuration: When stacked, the total height reaches 79-1/2 inches (202 cm). The dryer unit itself is approximately 22-1/2 inches (57.15 cm) in this configuration.

Riser and Pedestal Options:

• A 7-inch riser raises the door opening and height, remaining ADA compliant.
• A 16-inch pedestal also raises the door opening and height.

Special Installation Requirements

Stacked Installation:

Brackets for stacking the dryer over a washer are not included. Order part number GFA28KITN.

Alcove or Closet Installation:

• Approval for alcove/closet installation is indicated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances to adjacent walls or surfaces are 0" on all sides and top.
• Closet doors must be louvered or ventilated, with a minimum of 60 sq. in. of open area equally distributed. If a washer and dryer are in the same closet, doors need 120 sq. in. of open area.
• No other fuel-burning appliance should be in the same closet with a gas dryer.

Bathroom or Bedroom Installation:

• The dryer MUST be exhausted to the outdoors.
• Installation must comply with local codes, or the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers, in their absence.

Minimum Clearance (Other than Alcove/Closet):

Minimum clearances to combustible surfaces are 0" on all sides and top. A 1/2" clearance on each side is suggested for improved performance.

For more information on venting kits and accessories, call 1-800-GE-CARES.

Dryer Accessories

Warranty

Dryer Exhausting Information – Metal Duct Only

For complete information, see installation instructions packed with your dryer.

Ducting Materials:

For best performance, use 4" diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, UL-listed flexible metal (semi-rigid) ducting can be used (Kit PM08X10084 or PM08X10085). In special installations, a flexible metal (foil-type) duct may be necessary to connect to the house vent. UL-listed flexible metal (foil-type) duct is permissible ONLY where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4" diameter is maintained throughout the transition duct. Refer to installation instructions for complete details on using flexible metal (foil type) ducting.

Exhaust Length Calculation:

1. Determine the number of 90° turns needed. Add one turn if exhausting to the side or bottom of the dryer.
2. The maximum length of 4" rigid (aluminum or galvanized) duct is shown in the table below.

A turn of 45° or less can be ignored. Two 45° turns within the duct length count as one 90° elbow. A turn over 45° counts as one 90° elbow.

Dryers must be exhausted to the outside.

Caution:

For personal safety, do not terminate exhaust into a chimney, under an enclosed house floor (crawl space), or into an attic, as accumulated lint can create a fire hazard or moisture can cause damage. Never terminate exhaust into a common duct or plenum with a kitchen exhaust, as lint and grease combination can create a fire hazard.

Exhaust ducts should terminate in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must be located at least 12" above the ground or any other obstruction, with the opening pointed down.

For more information on venting kits and accessories, call 1-800-GE-CARES.

Exhaust Performance Table:

Diagram Description: The back view of the dryer shows the exhaust port and electrical connection points. An optional 55" power cord is also indicated.

Features and Benefits

• Steam Cycle: Refreshes small loads and dewrinkles larger loads using steam.
• Washer Link: Wirelessly connects your washer to your dryer, allowing you to select settings on one appliance for both.
• Built-in WiFi: Start, stop, and monitor your laundry from anywhere, receiving real-time notifications and updates.
• Steam Sanitize: Sterilizes clothing with elevated temperatures to kill common household germs and bacteria, while using steam to reduce wrinkles and odors.
• Quick Dry: Dries items and small loads quickly for busy households.
• Reduce Static: Prevents static cling with a gentle mist at the end of the cycle.
• Wrinkle Care: Prevents wrinkles by extending tumbling without heat.
• Damp Alert: Signals when delicate clothes reach the ideal dampness level for ironing or air drying.
• Convenient 4-Way Venting: Flexible venting options allow airflow from the front, rear, or either side (requires Kit GFA28DSVN).
• Reversible Door: Allows for easy reversal of the washer and dryer doors for flexible installation.
• Check Vent Notification: Provides a notification when the dryer vent needs cleaning, ensuring safe operation and optimal drying performance.