NIKKOR Z 50mm f/1.8 S User's Manual

Warranty Information

This Nikon equipment is guaranteed against manufacturing defects for one year from the original purchase date. If the product proves defective due to improper material or workmanship, Nikon's authorized service network will repair it without charge for labor and parts, subject to terms and conditions. Nikon reserves the right to replace or repair the product at its discretion.

Limitations: This warranty does not cover normal wear and tear, unauthorized modifications, transport costs, or damage from misuse, accidents, or unauthorized repairs. It does not affect your statutory consumer rights.

For authorized service stations, visit: https://www.europe-nikon.com/service/

Introduction

Before using this product, please carefully read both these instructions and the camera manual. This lens is intended exclusively for use with mirrorless cameras featuring a Nikon Z mount.

For Your Safety

⚠️ WARNING: Failure to observe precautions marked with this icon could result in death or severe injury.

❗ CAUTION: Failure to observe precautions marked with this icon could result in injury or property damage.

• WARNING: Do not disassemble or modify. Do not touch exposed internal parts. Failure to observe could result in electric shock or injury.
• If smoke, heat, or unusual odors are produced, disconnect power immediately. Continued operation could result in fire, burns, or injury.
• Keep dry. Do not handle with wet hands. Failure to observe could result in fire or electric shock.
• Do not use in the presence of flammable dust or gas (e.g., propane, gasoline, aerosols). Failure to observe could result in explosion or fire.
• Do not directly view the sun or other bright light source through the lens. Failure to observe could result in visual impairment.
• Keep out of reach of children. Small parts pose a choking hazard. Seek immediate medical attention if swallowed.
• Do not handle with bare hands in extreme temperatures. Failure to observe could result in burns or frostbite.

• CAUTION: Do not leave the lens pointed at the sun or other strong light sources. Focused light could cause fire or damage internal parts. Keep the sun out of frame when shooting backlit subjects.
• Do not leave the product in locations exposed to extremely high temperatures for extended periods (e.g., enclosed car, direct sunlight). Failure to observe could result in fire or product malfunction.
• Do not transport cameras or lenses with tripods or similar accessories attached. Failure to observe could result in injury or product malfunction.

Notice for European Customers: This symbol indicates that electrical and electronic equipment must be collected separately. Dispose of this product at an appropriate collection point, not as household waste. Separate collection and recycling conserve natural resources and prevent negative environmental and health consequences.

Using the Lens

Parts of the Lens: Names and Functions

Refer to the diagram showing lens components:

• q Lens hood mark: Use when attaching the lens hood.
• w Control ring: In autofocus mode, this customizable ring can be rotated to perform a selected camera function. In manual focus mode, rotate to focus.
• e Lens mounting mark: Use when mounting the lens on the camera.
• r Rubber gasket: Seals the lens mount.
• t CPU contacts: Transfer data to and from the camera.
• y Focus-mode switch: Select A for autofocus, M for manual focus. Manual focus adjustment is required when M is selected.
• u Lens hood: Blocks stray light to prevent flare or ghosting and protects the lens.
• i Lens hood lock mark: Use when attaching the lens hood.
• o Lens hood alignment mark: Use when attaching the lens hood.
• !0 Front lens cap: Protects the front element.
• !1 Rear lens cap: Protects the rear element and mount.

Attaching and Removal

Attaching the Lens

1. Turn the camera off, remove the body cap, and detach the rear lens cap.
2. Position the lens on the camera body, aligning the mounting mark on the lens with the mounting mark on the camera body. Rotate the lens counterclockwise until it clicks into place.

Removing the Lens

1. Turn the camera off.
2. Press and hold the lens release button while turning the lens clockwise.

Attaching and Removing the Lens Hood

Align the lens hood mounting mark (q) with the lens hood alignment mark (o). Rotate the hood (w) until the mark (i) aligns with the lens hood lock mark. To remove, reverse the steps.

When attaching or removing the hood, hold it near the [lens hood symbol] on its base and avoid gripping it too tightly. The hood can be reversed and mounted on the lens when not in use.

When the Lens Is Attached

The focus position may change if you turn the camera off and then on again after focusing. Refocus before shooting. If you have pre-focused while waiting for a subject, do not turn the camera off until the picture is taken.

Precautions for Use

• Do not pick up or hold the lens or camera using only the lens hood.
• Keep the CPU contacts clean.
• If the rubber lens-mount gasket is damaged, cease use immediately and take the lens to a Nikon-authorized service center for repair.
• Replace the front and rear lens caps when the lens is not in use.
• Store the lens out of direct sunlight to protect its interior.
• Keep the lens dry. Rusting of the internal mechanism can cause irreparable damage.
• Leaving the lens in extremely hot locations could damage or warp plastic parts.
• Rapid temperature changes may cause damaging condensation. Before moving the lens between environments of different temperatures, place it in its case or a plastic bag to slow the temperature change.
• Use the lens case to protect it from scratches during transport.

Lens Care

• Removing dust is normally sufficient for cleaning glass surfaces.
• Smudges and fingerprints can be removed using a soft, clean cotton cloth or lens cleaning tissue lightly dampened with ethanol or lens cleaner. Wipe gently from the center outwards in a circular motion. Avoid touching the lens with fingers.
• Never use organic solvents such as paint thinner or benzene.
• Neutral Color (NC) filters can be used to protect the front lens element.
• Store the lens in a cool, dry location to prevent mold and rust if not used for an extended period. Do not store in direct sunlight or with mothballs.

Accessories

Supplied Accessories

• LC-62B 62 mm snap-on Front Lens Cap
• LF-N1 Rear Lens Cap
• HB-90 Bayonet Hood
• CL-C1 Lens Case

Using the Lens Case

The case is intended to protect the lens from scratches, not from falls or other physical shocks. It is not water-resistant. The material may fade, bleed, shrink, or change color when rubbed or wet. Remove dust with a soft brush. Water and stains can be removed with a soft, dry cloth. Do not use alcohol, benzene, thinner, or other volatile solvents or detergents. Do not store in direct sunlight, high temperatures, or humidity. Do not use the case to clean monitors or lens elements. Be careful not to drop the lens from the case during transport.

Material: Polyester

Compatible Accessories

• 62 mm screw-on filters

Filters

Use only one filter at a time. Remove the lens hood before attaching filters or rotating circular polarizing filters.

Specifications

Nikon reserves the right to change the appearance, specifications, and performance of this product at any time and without prior notice.