FEZIBO ASSEMBLY INSTRUCTION

For Use With FEZIBO Desktops 48 and larger

For Assembly assistance, email service@fezibo.com

L-Shaped Standing Desk Overview

Illustrations show two configurations of the L-shaped standing desk: one with the longer desktop section on the right, and another with the longer section on the left.

Safety Precautions

• ⚠️ Keep children and pets away from the electric height-adjustable desk during operation. Unplug the power cord during a thunderstorm or if you do not intend to use the desk for a long time.
• ⚠️ Make sure the desktop does not touch the wall.
• ⚠️ Ensure no obstacles are in the desk's path and no objects are above or below the desk (within 20 inches).
• ⚠️ Working environment temperature: 0-40°C. Keep products away from corrosive gas, liquid, and dusty objects.
• ⚠️ It is strictly forbidden to disassemble the products privately to avoid product failure or damage to the human body caused by electronic components.
• ⚠️ Although the product has an anti-collision function, to avoid any pinching, ensure that hands or other body parts are in a safe position during operation. Anti-collision is not enabled during all resets.
• ℹ️ Please read the following instructions carefully before starting to use the height-adjustable desk. The company does not bear any warranty or liability for damage and human injury caused by abnormal operation.
• ℹ️ It is necessary to reset manually after initial installation or power off.

Parts List

Components:

• A - Column A
• B - Column B
• C - Long Foot
• D - Short Foot
• E - Long Girder
• F - Short Girder
• G - Connecting Girder
• H - Connecting board
• I - Bracket
• J - Hook x 2
• K - Sync Rod
• M - Connecting board x 2
• N - Control Box
• O - Power Supply
• P - Power Cord
• Q - Long Side Bracket
• R - Short Side Bracket
• S - Cable clip x 6
• T - ST4.8x13 screw x 42
• U - ST2.9x15 screw x 2
• V - M6x16 Screw x 8
• W - M6x10 Screw x 18
• X - Wooden pin x 8
• Y - M5 Allen Key
• Z - M3 Allen Key

Tools Needed (Not Included):

• [Electric Drill]
• [Phillips Screwdriver]

Note: Refers to Table board 1/2/3.

Assembly - Right-Hander Configuration

Step 1-R: Attach Frame Components

Description: Connect Column A and Column B to the Connecting Girder (G) using Long Girder (E) and Short Girder (F). Secure with screws (W).

Parts Used: A, B, E, F, G, W (x14)

Step 2-R: Install Sync Rod

Description: Insert the Sync Rod (K) into the designated holes on the columns. Ensure it is loose initially, then tighten using the M3 Allen Key (Z).

Parts Used: K, Z

Step 3-R: Attach Side Brackets

Description: Attach the Long Side Bracket (Q) and Short Side Bracket (R) to the frame using screws (W).

Parts Used: Q, R, W (x4)

Step 4-R: Attach Feet

Description: Attach the Long Foot (C) or Short Foot (D) to the bottom of the columns using screws (V). Ensure correct orientation.

Parts Used: C or D, V (x8)

Step 5-R: Prepare and Attach Desktop

Description: Place the desktop sections (1, 2, 3). Attach Connecting Boards (M) and Connecting Board (H) to the underside of the desktop using Wooden Pins (X) and screws (T). Use an electric drill for screws. Avoid excessive tightening.

Parts Used: Desktop sections, M (x2), H, X (x8), T (x16)

Step 6-R: Attach Hooks

Description: Attach Hooks (J) to the frame using screws (T). Use an electric drill. Avoid excessive tightening.

Parts Used: J (x2), T (x20)

Step 7-R: Prepare Brackets

Description: Illustrates rotating bracket components to 90-degree angles.

Step 8-R: Attach Brackets

Description: Attach Brackets (I) to the frame using screws (T). Avoid excessive tightening.

Parts Used: I, T (x4)

Step 9-R: Mount Control Box

Description: Mount the Control Box (N) to the frame using screws (U). Avoid excessive tightening.

Parts Used: N, U (x2)

Step 10-R: Connect Power and Cables

Description: Connect the Power Supply (O) and Power Cord (P) to the Control Box (N). Secure cables using Cable Clips (S).

Parts Used: O, P, N, S (x6)

Assembly - Left-Hander Configuration

Step 1-L: Attach Frame Components

Description: Connect Column A and Column B to the Connecting Girder (G) using Long Girder (E) and Short Girder (F). Secure with screws (W).

Parts Used: A, B, E, F, G, W (x14)

Step 2-L: Install Sync Rod

Description: Insert the Sync Rod (K) into the designated holes on the columns. Ensure it is loose initially, then tighten using the M3 Allen Key (Z).

Parts Used: K, Z

Step 3-L: Attach Side Brackets

Description: Attach the Long Side Bracket (Q) and Short Side Bracket (R) to the frame using screws (W).

Parts Used: Q, R, W (x4)

Step 4-L: Attach Feet

Description: Attach the Long Foot (C) or Short Foot (D) to the bottom of the columns using screws (V). Ensure correct orientation.

Parts Used: C or D, V (x8)

Step 5-L: Prepare and Attach Desktop

Description: Place the desktop sections (1, 2, 3). Attach Connecting Boards (M) and Connecting Board (H) to the underside of the desktop using Wooden Pins (X) and screws (T). Use an electric drill for screws. Avoid excessive tightening.

Parts Used: Desktop sections, M (x2), H, X (x8), T (x16)

Step 6-L: Attach Hooks

Description: Attach Hooks (J) to the frame using screws (T). Use an electric drill. Avoid excessive tightening.

Parts Used: J (x2), T (x20)

Step 7-L: Prepare Brackets

Description: Illustrates rotating bracket components to 90-degree angles.

Step 8-L: Attach Brackets

Description: Attach Brackets (I) to the frame using screws (T). Avoid excessive tightening.

Parts Used: I, T (x4)

Step 9-L: Mount Control Box

Description: Mount the Control Box (N) to the frame using screws (U). Avoid excessive tightening.

Parts Used: N, U (x2)

Step 10-L: Connect Power and Cables

Description: Connect the Power Supply (O) and Power Cord (P) to the Control Box (N). Secure cables using Cable Clips (S).

Parts Used: O, P, N, S (x6)

Operating Instructions

Manual Reset

ℹ️ It is necessary to reset manually after initial installation or power off.

1. Press and hold the 'down' key (▼) until the display shows "E-1" and "rES" alternately, then release the key.
2. Continue holding the 'down' key. The desktop will move down slowly and return to display "27.6".
3. Release the key. The height-adjustable desk resetting is finished.

⚠️ Note: The anti-collision function is not enabled during all resets. Be aware of potential pinching and ensure no obstacles are in the desk's path.

Up and Down

1. Press and hold the 'up' key (▲) until the required height is reached.
2. Press and hold the 'down' key (▼) until the required height is reached.

Saving Position

1. Adjust the desktop to the desired height.
2. Press the 'S' key. The display will show "S--".
3. Press a number key (1, 2, or 3). The display will show "S-1" (or S-2, S-3) and the desktop height alternately.
4. Press the 'S' key again. The memory position is set successfully. Repeat for other memory positions.

Anti-Collision Function

ℹ️ Before use, ensure obstacles and human bodies are clear of the desk's path.

1. If the desktop encounters an obstacle, the screen displays "E-2".
2. The desktop will move a short distance in the opposite direction and can be used normally after the obstacle is removed.

Container and Self-Stop Positions

ℹ️ Use this function only when necessary.

1. Press and hold 'S' for 3 seconds to enter the setup menu (display shows "S--").
2. Press 'up' key (▲) until "HLP" flashes.
3. Press '1'. The display shows "H-P" and the current height alternately.
4. Press 'up' or 'down' keys (▲/▼) to set the upper limit position.
5. Press 'S' to save the upper limit. The desktop height is displayed.
6. Press '2'. The display shows "L-P" and the current height alternately.
7. Press 'down' key (▼) to set the lower limit position.
8. Press 'S' to save the lower limit.

ℹ️ Note: This function limits the desktop's movement area, useful when a container is underneath or a shelf is above. The set limits are stored.

Change Display Unit (cm/inch)

1. Press and hold 'S' until the display shows "S--".
2. Press the 'up' key (▲). The display shows "Unt".
3. Press '1'. The display shows "Unt" and the height in "cm" alternately.
4. Press 'S' to save the unit as centimeters.
5. Press '2'. The display shows "Unt" and the height in "inch" alternately.
6. Press 'S' to save the unit as inches.

Amend the Desktop Height Displayed

This function allows adjusting the displayed height to match actual measurements.

1. Press and hold the 'down' key (▼) until the display shows "E-1" and "rES" alternately, then release.
2. Press and hold the 'S' key until the display shows "A - -".
3. Press 'Up' or 'Down' keys (▲/▼) until "End" and the height are displayed. (Unit is mm or inch).
4. Press '1', '2', or '3' to select the digit to adjust. Pressing the number key again increments that digit by 1.
5. Press 'S' to save the adjusted height.

Plug Detection

ℹ️ This function can detect if motors are connected correctly.

1. If the display shows "E-3" and "rES", check motor connections. Reconnect the main cable and wait at least 5 seconds.
2. Connect all plugs securely.
3. Follow the "Manual Reset" procedure.

Restore Factory Setting

ℹ️ This function resets the control unit to factory settings.

1. Press and hold 'S' until the display shows "FAC".
2. Press 'S' to confirm. The control unit will reset, including memory positions and container/shelf-stop positions.

Troubleshooting and Technical Data

Code Meaning

Troubleshooting

Technical Data

Why Choose FEZIBO?

Many ergonomic office solutions come at high cost. FEZIBO's mission is to use innovation, creativity, and efficiency to produce more affordable solutions that do not sacrifice quality and are easily accessible to millions of home and office workers globally.

Warranty Service

To provide the best service, register your FEZIBO product to confirm your warranty. This process grants access to services such as technical support, new product alerts, promotions, and warranty service.

Send your name and order ID to: service@fezibo.com

For more FEZIBO products, visit: www.fezibo.com