Defiant Motion Security Light Use and Care Guide

Table of Contents

• Safety Information
• Warranty
• Pre-Installation
• Installation
• Operation
• Care and Cleaning
• Troubleshooting

Safety Information

PRECAUTIONS

• Please read and understand this entire manual before attempting to assemble, install, or operate this light fixture.
• This light fixture requires 120-volts AC.
• Some codes require installation by a qualified electrician.
• This light fixture must be properly grounded.
• This light fixture is intended for use with the enclosed gasket and with a junction box marked for use in wet locations.
• This light fixture should be installed outdoors to a wall or eave.
• The light fixture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light fixture is mounted higher than recommended, aiming the sensor down will reduce the coverage area.
• Do not leave the "ON-TIME" switch in the "TEST" position. The frequent ON/OFF cycling of the light fixture will reduce the life of the bulb.
• WARNING: Risk of fire. Do not aim the bulbs at a combustible surface within 3 ft. (1 m).
• WARNING: Risk of fire. Keep the bulbs at least 2 in. (51 mm) from combustible materials.
• CAUTION: Keep the motion sensor at least 1 in. (25 mm) away from the bulbs.
• CAUTION: Keep the bulb holders 30° below horizontal to avoid water damage and electrical shock.
• CAUTION: To avoid water damage and the risk of electrical shock, the motion sensor controls must be facing the ground when the installation is complete.
• CAUTION: Burn hazard. Allow the light fixture and the bulb to cool before touching.
• CAUTION: Do not cut any wires with factory installed wire connectors or remove the wire connectors.
• NOTICE: Do not connect this light fixture to a dimmer switch or timer.

Warranty

2-YEAR LIMITED WARRANTY

WHAT IS COVERED

This product is guaranteed to be free of factory defective parts and workmanship for a period of 2 years from date of purchase. Purchase receipt is required for all warranty claims.

WHAT IS NOT COVERED

This guarantee does not include repair service, adjustment and calibration due to misuse, abuse or negligence. Any damage to the light fixture resulting from the use of chemicals or a pressure washer machine are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components that a customer uses in conjunction with this product.

No service parts available for this product.

Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com.

Pre-Installation

PLANNING INSTALLATION

Before installing the light fixture, ensure that all parts are present (see Hardware Included on page 4). If any part is missing or damaged, do not attempt to assemble, install, or operate this light fixture.

Estimated installation time: 30 minutes

SPECIFICATIONS

TOOLS REQUIRED

• Phillips screwdriver ?
• Flathead screwdriver ?
• Pliers ?
• Wire strippers/cutters ✂️
• Circuit tester ⚡
• Work gloves ?
• Electrical tape ?
• Silicone sealant ?
• Ladder ?
• Safety goggles ?

HARDWARE INCLUDED

NOTE: Hardware shown to actual size.

Part Descriptions:

• AA: Wire connector (3)
• BB: Rubber plug (1)
• CC: Mounting bolt (1)
• DD: Mounting bracket screw (2)
• EE: Mounting bracket screw (2)
• FF: Mounting bracket screw (2)
• GG: Gasket (1)
• HH: Mounting bracket (1)
• II: Plastic hanger (1)

PACKAGE CONTENTS

• A: Bulb holder (2)
• B: Canopy (1)
• C: Motion sensor (1)
• D: Shell (2)

Installation

1. Determining the mounting location

NOTE: The light fixture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light fixture is mounted higher than recommended, aiming the sensor down will reduce the coverage area.

• Determine the mounting location – a wall or under an eave.
• Position bulb holders (A) in the general direction of the desired light coverage and tighten the lock nuts (1) and the thumb screws (2).
• If needed, lift the motion sensor (C) up and rotate it so the controls face the ground after installation. Tighten the clamp screw (3) when done. Do not overtighten.

NOTE: If the motion sensor pops out of the ball joint, loosen the clamp screw, push the motion sensor back into the ball joint, and tighten the clamp screw. Do not overtighten.

Diagrams: Wall Mount and Eave Mount showing placement of components.

2. Installing the mounting bracket

• WARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light fixture.
• Remove the existing light fixture.
• Install the mounting bracket (HH) with the stamped word “FRONT” facing away from the junction box. Use the mounting bracket screws (DD, EE, or FF) that best fit the junction box.

NOTE: Firmly pull on the mounting bracket to verify it is securely mounted to the junction box. If necessary, use the screws that were removed from the existing light fixture.

Diagram: Shows mounting bracket installation.

3. Hanging the light fixture temporarily

• Insert the small end of the plastic hanger (II) through the center hole of the canopy (B) and the gasket (GG).
• Insert the small end of the plastic hanger (II) into one of the two small, slotted holes on the mounting bracket (HH).
• Route the light fixture wires through the large holes in the gasket (GG).

Diagram: Shows temporary hanging of the fixture.

4. Wiring the light fixture

• CAUTION: Do not cut any wires with factory installed wire connectors or remove the wire connectors.
• Connect the light fixture wires to the junction box wires with wire connectors (AA): White to white, Black to black, Bare or green ground wire to house ground.

Diagram: Shows wire connections.

5. Mounting the light fixture

• Remove the plastic hanger (II).
• Insert the small end of the mounting bolt (CC) through the center hole of the canopy (B) and the gasket (GG).
• Align the mounting bolt (CC) with the center hole in the mounting bracket (HH) and tighten securely. Do not overtighten.
• Push the rubber plug (BB) firmly into the mounting bolt hole on the canopy (B).

NOTE: Make sure all the wires are inside the junction box before attaching the canopy to the junction box.

Diagram: Shows final mounting of the fixture.

6. Caulking around the light fixture

• CAUTION: Failure to completely caulk around the light fixture's canopy could result in water seepage into the junction box.
• Caulk around the canopy (B) and mounting surface with silicone sealant (not included).

7. Installing the shells and bulbs

• Align the three slots on the shell (D) with the three nibs on the bulb holder (A).
• Insert the shell (D) into the bulb holder (A) and twist clockwise to lock.
• Repeat for the other shell (D).
• Install bulbs (not included) into both bulb holders (A).

Operation

1. Adjusting the bulb holders

• WARNING: Risk of fire. Do not aim the bulbs at a combustible surface within 3 ft. (1 m).
• WARNING: Risk of fire. Keep the bulbs at least 2 in. (51 mm) from combustible materials.
• CAUTION: Keep the sensor at least 1 in. (25 mm) away from the bulbs.
• CAUTION: Keep bulb holders 30° below horizontal to avoid water damage and electrical shock.
• Turn the power on at the circuit breaker or fuse and turn on the wall switch.
• Loosen the lock nut (1) and thumb screw (2) to adjust the bulb holders (A) for the desired light coverage.
• Tighten the lock nut (1) and thumb screw (2).

NOTE: Do not rotate the bulb holders more than 180° from the factory setting.

2. Rotating sensor controls downward

• CAUTION: To avoid water damage and risk of electrical shock, the motion sensor controls must be facing the ground when installation is complete.
• Rotate the motion sensor (C) so the controls face toward the ground.

NOTICE: All clearances must be maintained. See Safety Information on page 2.

3. Setting the sensor for testing

NOTE: When the "ON-TIME" dial is turned to the "TEST" position, the light fixture will operate during the day or night. The light will stay on for 5 seconds after all motion is stopped.

NOTE: The motion sensor will need to completely warm up (90 seconds) before beginning the setup process.

• Turn the "ON-TIME” dial to the “TEST” position.
• Turn the "DUALBRITE" dial to the "OFF” position.
• Turn the "RANGE” dial to the “MIN” position.
• Aim the motion sensor (C) in the general direction of the area to be covered.

Diagram: Shows the sensor dials: RANGE, ON-TIME, DUAL BRITE.

4. Adjusting the motion sensor detection zone

• Turn on the circuit breaker or fuse and the light switch.
• Perform a "walk test". Walk in an arc across the front of the motion sensor (C).
• Watch the light. The light will come on and the red LED will flash indicating motion has been detected.
• Stop, wait for the light to turn off, and then begin walking again.
• Continue this process until the detection zone has been established.
• Adjust the sensor up, down, or side to side to change the motion sensor (C) detection zone.

5. Adjusting the RANGE dial

• To increase the detection zone, turn the “RANGE” dial toward the “MAX” position.
• To decrease the detection zone, turn the “RANGE” dial toward the “MIN” position.

NOTE: The motion sensor is more sensitive to motion moving across the front of the sensor. The motion sensor is less sensitive to motion moving directly toward the front of the sensor.

NOTE: The higher the "RANGE" setting (sensitivity), the greater the possibility of false triggering. To reduce false triggering, rotate the "RANGE” control toward the "MIN" setting.

6. Adjusting the ON-TIME dial

NOTE: The "ON-TIME" dial determines the amount of time the light will stay on full bright after all motion has stopped. When the "ON-TIME" dial is set to the 1, 5, or 20 minute position, the light will only come on during the night.

• Turn the "ON-TIME” dial to the 1, 5, or 20 minute position.

7. Adjusting the DUALBRITE dial

NOTE: The "DUALBRITE" feature determines the amount of time the lights stay on at an accent level after sundown when there is no motion. Switching this setting to "OFF" will not affect the "ON-TIME" setting or the photocell.

• Turn the "DUALBRITE” dial to OFF, 3 hours, 6 hours, or dusk-to-dawn (sunset to sunrise).

8. Using manual mode

NOTE: Manual mode overrides the motion sensor so the light will operate full bright. This feature only works at night and only for one night at a time. The motion sensor will reset to motion sensing mode after 6 hours or sunrise, whichever comes first. Manual mode can be toggled on and off using a wall switch.

• To turn manual mode on, switch the light off at the wall switch for 3 to 4 seconds and then back on.
• To turn manual mode off, switch the light off at the wall switch for 3 to 4 seconds and then back on.

NOTE: If the power to the light fixture is off for more than 5 seconds, allow the motion sensor to warm up prior to switching to manual mode.

FCC Compliance Statement: This device complies with Part 15 of the FCC Rules...

Care and Cleaning

• To prolong the original appearance, clean with clear water and a soft, damp cloth only.
• Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish. This is not a defect in the finish and will not be covered by the warranty.
• Do not spray the light fixture with a hose or power washer.

Troubleshooting