Victrola Venture VSC-680SB

Turntable Layout

The Victrola Venture VSC-680SB features a comprehensive layout for easy operation. Key components include:

• 1. Turntable Platter: The rotating surface for vinyl records.
• 2. Turntable Spindle: The central post that holds the record.
• 3. 45 RPM Adaptor: A small disc used for playing 7-inch records with large center holes.
• 4. Lift Lever: A mechanism to raise and lower the tonearm.
• 5. Tone Arm Clip: Secures the tonearm when not in use.
• 6. Line-In Jack: An auxiliary input for connecting external audio devices.
• 7. Auto Stop Switch: Controls automatic stopping of the turntable at the end of a record.
• 8. Function Knob: Selects the audio source: BT (Bluetooth), LINE-IN (Aux-In), PHONO (Vinyl), VINYLSTREAM™ (Bluetooth Out).
• 9. Speed Selection Switch: Adjusts the turntable speed for 33 1/3, 45, or 78 RPM records.
• 10. Tone Arm: Holds the stylus and tracks the record groove.
• 11. Power On / Off / Volume Control Knob: Controls the unit's power and audio volume.
• 12. Power / Bluetooth Light Indicator: Shows the power status and Bluetooth connection.
• 13. Stylus Cartridge: Contains the needle that reads the record groove.
• 14. Headphone Jack: For connecting headphones or earbuds.
• 15. Buckle: Secures the turntable lid.
• 16. Handle: For carrying the turntable.
• 17. Internal Speakers: Built-in speakers for audio playback.
• 18. RCA Output Jack: Connects to external audio systems (e.g., amplifiers, powered speakers).
• 19. Power Adaptor Jack: For connecting the included power adapter.

The unit also features connections on the rear panel, including RCA Output Jacks (18) and a Power Adaptor Jack (19).

Initial Setup

To set up your Victrola Venture turntable:

1. Place the unit on a flat, level surface and open the buckle to lift the lid.
2. Remove all packing materials, including any twist ties securing the tonearm.
3. Gently pull the stylus cover forward to remove it.
4. Plug the included power adapter into the unit and then into a wall outlet.

Vinyl Mode

Enjoy your vinyl records with the Victrola Venture.

To Play a Record:

1. Turn the unit ON using the power knob (the LED indicator will turn Red).
2. Rotate the function knob to the PHONO (Vinyl) mode.
3. Place a vinyl record onto the turntable platter.
4. Release the tonearm from its clip.
5. Use the lift lever to gently raise the tonearm.
6. Move the tonearm over the edge of the record and lower the lift lever to begin playback.
7. Adjust the volume using the power/volume control knob.

Speed Selector Switch: Use this switch to select the correct playback speed (33 1/3, 45, or 78 RPM). Use the included 45 RPM adaptor for 7-inch records.

Auto Stop Selection Switch:

• If ON: The record will start spinning when the tonearm is moved over it and will stop automatically when playback finishes.
• If OFF: The record will start spinning when the unit is in PHONO mode, and will continue to spin even after playback is finished.

RCA Line Out: Connect the red and white RCA connectors on the back of the unit to an amplifier or stereo device. Ensure the volume on the record player is at a minimum before connecting, then increase as needed.

Headphones: Connect your headphones or earbuds to the headphone jack on the platter. Reduce the record player's volume to a minimum before connecting, then increase as needed.

Note:

• Handle vinyl records only by their edges or center label to avoid damaging the grooves.
• If no sound is playing, ensure the function knob is set to Vinyl mode, as it might be in Vinylstream mode.

Vinylstream™ Mode

Play your vinyl records wirelessly through an external Bluetooth speaker or headphones.

1. Turn the unit ON (LED indicator will turn Red).
2. Rotate the function knob to BT OUT (Vinylstream) mode. The unit will begin searching for Bluetooth devices (LED will flash Red).
3. Turn on your external Bluetooth speaker or headphones and set them to pairing mode.
4. The Victrola Venture unit will chime when it successfully connects to your device (LED will stop flashing).
5. Use your external device to control the volume.

Notes:

• In Vinylstream mode, the internal speakers of the Victrola Venture are disengaged.
• For initial pairing, place the Bluetooth device within 1 meter (3.3 feet) of the product.
• For the strongest connection, ensure the unit remains within 10 meters (33 feet) of your external Bluetooth device.

Bluetooth Mode

Connect your smartphone, tablet, or other Bluetooth-enabled device to play music through the Victrola Venture's speakers.

1. Turn the unit ON (LED indicator will turn Red).
2. Rotate the function knob to BT (Bluetooth) mode. The unit will begin searching for Bluetooth devices (LED will flash Blue).
3. On your device, turn on Bluetooth and select "Victrola Venture" from the list of available devices.
4. The unit will chime when connected (LED will stop flashing).
5. Use the Power/Volume Knob to adjust the volume.

Note:

• Ensure your Bluetooth device is within 10 meters (33 feet) of the unit for the strongest connection.
• If no sound is playing, verify that the function knob is set to Bluetooth mode.

Aux-In Operation

Connect external audio devices using a 3.5mm auxiliary cable.

1. Connect your external audio device to the LINE IN jack on the turntable platter using a 3.5mm auxiliary cable (not included).
2. Turn the unit ON (LED indicator will turn Red).
3. Rotate the function knob to LINE IN (Aux-In) mode (LED will turn Purple).
4. Use the Power/Volume Knob to adjust the volume.
5. Use the controls on your external audio device to manage playback functions.

Stylus Replacement

Replacing the stylus is a simple process to maintain optimal sound quality.

Removing the Stylus from the Tonearm:

1. Place your fingers at the tip of the stylus and push down towards direction "A". (Warning: Applying excessive force may damage or break the cartridge.)
2. Pull the stylus straight out towards direction "B".

Installing the Stylus:

(Replacement Stylus # ITNP-S1)

1. Hold the tip of the new stylus and insert the opposite edge into the cartridge, pressing towards direction "C".
2. Push the stylus upwards towards direction "D" until it locks securely into place.

Caution:

• Do not bend or force the stylus into the cartridge.
• Avoid touching the stylus needle to prevent injury.
• Always turn off the unit's power before replacing the stylus.
• Keep replacement parts out of reach of children.

Note: The stylus is designed to last approximately 300 hours of normal use. It is recommended to replace the stylus as soon as you notice a decline in sound quality. Playing records at 78 RPM may accelerate stylus wear, potentially requiring earlier replacement.

Specifications

Please note: As a result of continual improvements, the design and specifications of this product are subject to change without notice.

Bluetooth is a registered trademark of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.

Made In China.

Safety Instructions

1. Read all safety and operating instructions before operating this product.
2. Keep these instructions for future reference.
3. Heed all warnings on the appliance and in the operating instructions.
4. Follow all operating and use instructions.
5. Do not use this apparatus near water or moisture (e.g., in a wet basement, near a swimming pool).
6. Clean only with a dry cloth.
7. Do not block ventilation openings. Ensure at least 5 cm (2 inches) of clearance around the apparatus for ventilation. Install according to manufacturer's instructions.
8. Do not install near heat sources like radiators, heat registers, stoves, or other heat-producing apparatus (including amplifiers).
9. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has one blade wider than the other. A grounding plug has two blades and a third grounding prong. If the plug does not fit your outlet, consult an electrician.
10. Protect the power cord from being walked on or pinched, especially at the plugs, receptacles, and where it exits the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. Use caution when moving a cart/apparatus combination to avoid tip-over injuries.
13. Unplug the apparatus during lightning storms or when unused for extended periods.
14. Refer all servicing to qualified personnel. Servicing is required when the apparatus is damaged in any way, such as a damaged power cord or plug, spilled liquid, objects fallen into the apparatus, exposure to rain or moisture, abnormal operation, or if it has been dropped.
15. Please keep the unit in a well-ventilated environment.
16. Only use attachments/accessories specified or provided by the manufacturer.
17. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not place objects filled with liquids, such as vases, on the apparatus.
18. The main plug is used as the disconnect device; ensure it remains readily operable.
19. This product is not intended for commercial use; it is for Household Use Only.
20. This equipment is a Class II or double-insulated electrical appliance, designed not to require a safety connection to electrical earth.

Electrical Safety Symbols:

• ⚡️ (Lightning flash with arrowhead): Alerts the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be sufficient to cause a risk of electric shock.
• ⚠️ (Exclamation point): Alerts the user to important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Warning: To reduce the risk of fire or electrical shock, do not expose the apparatus to rain or moisture. No naked flame sources, such as candles, should be placed on top of the apparatus.

Caution: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this device. Using controls or adjustments, or performing procedures other than those specified herein, may result in hazardous exposure.

FCC and IC Statements

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

IC Statement

This device complies with RSS247 of Industry Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.

The device must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with IC radiation exposure limits set forth for an uncontrolled environment. Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC établies pour un incontrôlé environnement.

The device should be installed and operated with a minimum distance of 20cm between the radiator and your body. L'appareil doit être installé et utilisé avec une distance minimale de 20cm entre le radiateu et votre corps.

Limited Warranty

Victrola is a registered trademark of Innovative Technology Electronics, LLC.

United States

For detailed information about our warranty policy and limitations, visit victrola.com/pages/warranty.

Outside the U.S., Canada, and US Territories

The warranty on this product shall comply with applicable law when sold to a consumer outside of the United States, Canada, and US Territories. To obtain any applicable warranty service, please contact the dealer from which you purchased the product, or the distributor that supplied the product, with your original receipt.

Canada and US Territories

The warranty on this product shall comply with applicable law when sold to a consumer in Canada or a US Territory. To obtain any applicable warranty service, please contact the dealer from which you purchased the product, or the distributor that supplied the product, with your original receipt.

If assistance from the dealer from which it was purchased is not possible, you may contact customer service for warranty assistance at victrola.com/contact.

Customer Support

Visit: VICTROLA.COM/PAGES/CUSTOMER-CARE

Email: support@victrola.com

Phone: (877)483-2497