Ferrari SF1000 Radio-Controlled Model

Important Safety and General Information

General Disclaimer: Please read the complete instructions and safety guidelines carefully before operating the model. These are for your safety and can prevent accidents and injuries.

Age Suitability:

• Suitable for children over 8 years!
• Warning: Not suitable for children under 36 months. RISK OF SUFFOCATION! Contains small parts which can be swallowed. Keep away from children.
• This device is not intended for use by individuals (including children) with reduced physical, sensory, or mental abilities, or lack of experience and/or knowledge, unless they are supervised by a person responsible for their safety and instructed on how to use the device.

Certificate of Conformity

JAMARA e.K. declares that the product "Ferrari SF 1000, No. 403007" complies with Directive 2014/53/EU, 2011/65/EU and 2009/48/EC. The full text of the EU Declaration of Conformity is available at: www.jamara-shop.com/Conformity

Operating Precautions

Attention! Never operate your model beyond sight. Maximum visibility and range depend on factors like weather, location, and interfering frequencies. Before each use, perform a range test with a second person securely holding the model. Check how the model reacts to signal loss (e.g., empty transmitter batteries, switched-off transmitter).

Recommended Tools (Not Included)

A list of tools is indicated but not provided with the kit.

Assembly of Components

General Assembly Procedure:

• Take out all parts and ensure nothing is missing.
• Do NOT remove all parts at once; assemble step by step according to the manual's instructions.
• Apply stickers to components before installing them, as described in the instructions.
• Assemble the model according to the figures provided.

Sticker Application:

• Carefully peel the sticker off with tweezers.
• Hold the edge of the backplate and position the sticker on the model.
• Fix the sticker with fingers and ensure it is in place.
• Gently press the sticker downwards until bubbles disappear.

Assembly Steps

The following steps describe the assembly process based on the provided diagrams. Parts are identified by numbers and letters (e.g., 1, 2, 3, A5, B13, C25).

1. Battery Installation & Binding: Insert 2x AA batteries into the transmitter (Part 1) and 2 or 3x AA batteries into the model (Part 2), observing correct polarity. Replace battery compartment covers. Turn on the model (light flashes). Insert 2 AA batteries into the transmitter (LED flashes). When LEDs on both model and transmitter stop flashing, they are bound.
2. Chassis Assembly: Attach part A8 to the chassis using fastener 3.
3. Chassis Assembly: Attach part A7 to the chassis using fastener 3.
4. Chassis Assembly: Attach part A7 to part A8 using fastener 3.
5. Component Attachment: Attach part 56 to the chassis assembly using fastener 3.
6. Component Attachment: Attach part 57 to the chassis assembly using fastener 3.
7. Component Attachment: Attach part 10 to the chassis assembly using fastener 3.
8. Component Attachment: Attach part 27 to the chassis assembly using fastener 3.
9. Component Attachment: Attach part C35 to the chassis assembly using fastener 3.
10. Component Attachment: Attach part A9 to the chassis assembly using fastener 3.
11. Component Attachment: Attach part A10 to the chassis assembly using fastener 3.
12. Component Attachment: Attach part 11 to the chassis assembly using fastener 3.
13. Component Attachment: Attach part 61 to the chassis assembly using fastener 3.
14. Component Attachment: Attach part 60 to the chassis assembly using fastener 3.
15. Component Attachment: Attach part A12 to the chassis assembly using fastener 3.
16. Component Attachment: Attach part A11 to the chassis assembly using fastener 3.
17. Component Attachment: Attach part C37 to the chassis assembly using fastener 3.
18. Component Attachment: Attach part C25 to the chassis assembly using fastener 3.
19. Component Attachment: Attach part 56 to the chassis assembly using fastener 3.
20. Component Attachment: Attach part A11 to the chassis assembly using fastener 3.
21. Component Attachment: Attach part C29 to the chassis assembly using fastener 3.
22. Component Attachment: Attach part C26 to the chassis assembly using fastener 3.
23. Component Attachment: Attach part 13 to the chassis assembly using fastener 3.
24. Component Attachment: Attach part 57 to the chassis assembly using fastener 3.
25. Component Attachment: Attach part 54 to the chassis assembly using fastener 4.
26. Component Attachment: Attach part C32 to the chassis assembly using fastener 4.
27. Component Attachment: Attach part 55 to the chassis assembly using fastener 4.
28. Component Attachment: Attach part C33 to the chassis assembly using fastener 4.
29. Component Attachment: Attach part B18 to the chassis assembly using fastener 4.
30. Component Attachment: Attach part C31 to the chassis assembly using fastener 4.
31. Component Attachment: Attach part C38 to the chassis assembly using fastener 4.
32. Component Attachment: Attach part C30 to the chassis assembly using fastener 4.
33. Component Attachment: Attach part C27 to the chassis assembly using fastener 4.
34. Component Attachment: Attach part C28 to the chassis assembly using fastener 4.
35. Component Attachment: Attach part B14 to the chassis assembly using fastener 4.
36. Component Attachment: Attach part B15 to the chassis assembly using fastener 4.
37. Component Attachment: Attach part B13 to the chassis assembly using fastener 4.
38. Component Attachment: Attach part 59 to the chassis assembly using fastener 4.
39. Component Attachment: Attach part 51 to the chassis assembly using fastener 4.
40. Component Attachment: Attach part B23 to the chassis assembly using fastener 4.
41. Component Attachment: Attach part 51 to the chassis assembly using fastener 4.
42. Component Attachment: Attach part B24 to the chassis assembly using fastener 4.
43. Component Attachment: Attach part B17 to the chassis assembly using fastener 4.
44. Component Attachment: Attach part 58 to the chassis assembly using fastener 4.
45. Component Attachment: Attach part 62 to the chassis assembly using fastener 4.
46. Component Attachment: Attach part 61 to the chassis assembly using fastener 4.
47. Component Attachment: Attach part 63 to the chassis assembly using fastener 4.
48. Component Attachment: Attach part B16 to the chassis assembly using fastener 4.
49. Component Attachment: Attach part 60 to the chassis assembly using fastener 4.
50. Component Attachment: Attach part C39 to the chassis assembly using fastener 4.
51. Component Attachment: Attach part A5 to the chassis assembly using fastener 4.
52. Component Attachment: Attach part B22 to the chassis assembly using fastener 4.
53. Component Attachment: Attach part B21 to the chassis assembly using fastener 4.
54. Body Panel Attachment: Attach body panels (Parts 40, 41) to the chassis assembly, noting FRONT and REAR orientation, using fastener 4.
55. Final Assembly: Attach remaining parts as indicated in diagrams, potentially using fasteners 3 and 4.
56. Battery Compartment Wiring: Connect battery wires, observing polarity (+ and - symbols), potentially using part C36 and fasteners 4 and 3.

Transmitter Functions

Transmitter (Part 1):

• 1. Forward / Backward: Controls forward and reverse movement.
• 2. Left / Right: Controls steering.
• 3. Battery Compartment: Houses the transmitter batteries.
• A. Trim Lever: Adjusts steering trim for straight-line driving.
• B. On/Off Switch: Powers the transmitter on and off.
• C. Battery Compartment: (Same as 3)

Model (Part 2):

• A. Trim Lever: (Likely refers to steering trim on the car, though not explicitly labeled as such in diagrams).
• B. On/Off Switch: Powers the model on and off.
• C. Battery Compartment: Houses the model's batteries.

Battery and Binding Information

Battery Insertion: Remove the battery compartment cover. Insert 2 / 3 x AA batteries, observing correct polarity. Replace the battery hatch.

Binding Process: Turn on the model (light flashes). Insert 2 AA batteries into the transmitter (LED flashes). When the LEDs on both the model and transmitter stop flashing, they are bound.

Battery Warnings

General Battery Safety:

• Non-rechargeable batteries are not to be recharged!
• Do not open batteries!
• Do not dispose of batteries in fire!
• Do not mix old and new batteries!
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries!
• Rechargeable batteries must be removed from the toy before being charged!
• Rechargeable batteries are only to be charged under adult supervision!
• The supply terminals are not to be short-circuited!

Cooling and Overheating:

• Let the model cool off sufficiently after each use before putting it back into operation.
• When changing batteries, allow a cooling phase of at least 10 minutes before operating the model again.
• Overheating can damage electronics or cause a fire hazard.

General Safety Measures

• Keep hands away from moving parts.
• Use only under direct supervision of an adult!
• Battery Status: If batteries are depleted, replace them.
• Polarity: Pay attention to the correct polarity when inserting batteries.
• Frequency Interference: Be aware of frequencies in your environment.
• Environmental Conditions: Do not operate in rain, snow, wetness, or sand.
• Traffic Safety: Never drive on roads or areas used by real vehicles.
• Range: Never operate out of the reach of your remote control. Stay within sight.
• Temperature: Do not expose to direct sunlight or excessive heat.
• Cleaning: Clean by using a damp cloth.
• Storage: Store batteries/battery packs separately when not in use. Do not store batteries in the model.

Disposal Information

Battery Disposal: Batteries and accumulators must not be disposed of in domestic waste but must be disposed of separately. You are obliged to dispose of old batteries appropriately (separate collection). Return used batteries free of charge to retail stores. Batteries may contain substances that are irritant, can cause allergies, or are highly reactive. Separate collection and proper recycling are important for the environment and your health. If batteries are marked with Hg, Cd, or Pb below the crossed-out waste bin symbol, they contain more than 0.0005% mercury (Hg), 0.002% cadmium (Cd), or 0.004% lead (Pb).

Electrical Equipment Disposal: Electrical appliances must not be disposed of in domestic waste and must be disposed of separately. Remove batteries (if possible) and dispose of the electrical equipment at communal collection points. If personal data is stored on the equipment, remove it yourself.

Technical Specifications

• Frequency Bands: 2400MHz to 2483.5MHz
• Maximum Transmitting Power (EIRP): Not more than 10mW.
• Applicable Age: 8 years (96 months) and above.

Copyright and Licensing

All rights reserved. Copyright JAMARA e.K. 2022. Images belong to Rastar. Copying or reproduction in whole or part is only permitted with the expressed permission of JAMARA e.K.

Produced under license of Ferrari S.p.A. The name FERRARI, the PRANCING HORSE device, all associated logos and distinctive designs are property of Ferrari S.p.A. The body designs of the Ferrari cars are protected as Ferrari S.p.A. property under design, trademark and trade dress regulations.

Licensee: RASTAR (HK) INDUSTRIAL COMPANY LIMITED

Manufacturer: RASTAR GROUP

Address: Xinghui Industrial Park, Xiadao Road, Shanghua, Chenghai, Shantou, Guangdong, China.

Website: www.rastar.com

Imported by: JAMARA e.K. Inh. Manuel Natterer

Address: Am Lauerbühl 5 - DE-88317 Aichstetten

Contact: Tel. +49 (0) 75 65/94 12-0 - Fax +49 (0) 75 65/94 12-23

Email: info@jamara.com

Website: www.jamara.com

Service: Tel. +49 (0) 75 65/94 12-777

Email: service@jamara.com