manuals.plus
Simplicity
Simplicity Freedom S10CV Cordless Vacuum Owner's Manual
Owner's Manual for Simplicity models including: Simplicity, Freedom, S10CV, cordless vacuum, vacuum cleaner, owner's manual, instructions, maintenance, troubleshooting, warranty, Tacony Corporation, vacuum cleaner manual
2 QUICK START GUIDE QUICK START GUIDE 3 DBTMA100 - Safety Informa
Owner's Manual Use only as described in this manual. • Do not use charger with damaged cord or plug. If appliance or charger is not working as it should, has been dropped ...
(The chances are you’re never going to read me) No manual adjustments are required. The height of the nozzle automatically adjusts to the flooring surface. This self-adjusting feature allows the nozzle to float evenly over all flooring surfaces. oPeRAtIon Fig. 1 Fig. 2 MATERIAL DRAWN ISSUED SCALE FINISH DATE DATE DO NOT SCALE UNLESS OTHERWISE SPECIFIED DESCRIPTION
207069 (The chances are you're never going to read me)
Owner's Manual
Models S10CV
www.SimplicityVac.com
Getting Started Important Safety Instructions Polarization Instructions State of California Proposition 65 Warnings Description of the Vacuum Assembling the Vacuum
Operation Battery Charging
Battery Life Display Reclining the Handle On/Off Switch Edge Cleaning Automatic Carpet Height Adjustment Bare Floor Cleaning Vacuuming Under Furniture
Maintenance and Care Replacing the Vacuum Bag Removing and Reinstalling the Battery Removing and Reinstalling the Bottom Plate Replacing the Vacuum Belt Replacing the Squeegee Annual Checkup
Problem Solving Guide Troubleshooting Visit Simplicity Vacuums Online How to Contact Your Authorized Retailer Key Replacement Parts For Best Performance
Warranty
Contents
2 3 3 4 5
6 6 6 7 7 7 8 8
9 10 11 12 13 13
14 14 14 14 14
15
1
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS
APPLIANCE. FOR HOUSEHOLD USE ONLY.
IMPORTANT: The manufacturer cannot accept responsibility for damage caused when the appliance is not used according to the instructions, or for uses other than those for which it was intended.
WARNING: To reduce the risk of fire, electric shock, damage or injury:
· Fully assemble vacuum before operating.
· D o not use without vacuum bag in place.
· Use and store in a dry location.
· Use extra care when cleaning on stairs.
· Do not use outdoors or on wet surfaces.
· Do not allow to be used as a toy. Close attention is necessary when used by or near children.
· Use only as described in this manual.
· Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.
· Do not attempt to service the unit while charger is plugged in.
· Do not use charger with damaged cord or plug. If appliance or charger is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to your Authorized Simplicity Retailer for service.
· Do not pull or carry charger by cord, use cord as a handle, close a door on the cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
· Do not unplug charger by pulling on cord. To unplug charger, grasp the plug, not the cord.
· Do not handle charger, including charger plug, and charger terminals with wet hands.
· Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flow.
· Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts.
· Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
· Do not charge the unit outdoors.
· Only charge in temperatures between 0-45ºC (32-113ºF).
· Do not open, crush, expose to heat above 100ºC (212ºF) or incinerate the battery even if it is severely damaged. The battery can explode in a fire.
· Do not use with a damaged battery or charger. If the appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to your Authorized Simplicity Retailer.
· Use only with the Cordless Battery Vacuum Charger supplied - P/N 10201026 Winkind. (C223-2000)
· The battery and charger have no user serviceable parts.
· Batteries must be disposed of responsibly. Contact your Authorized Simplicity Retailer for information on battery disposal.
· Remove the battery before removing the bottom plate.
SAVE THESE INSTRUCTIONS.
2
Polarization instructions
Power Cord, 2-Wire Polarized Cord To reduce the risk of electric shock, the charger is equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact a qualified electrician to replace the obsolete outlet. Do not defeat the safety purpose of the polarized plug.
State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to
cause cancer. WARNING: This product contains one or more chemicals known to the State of California to
cause birth defects or other reproductive harm.
3
Description of the Vacuum
1 2
3 4
1
Ergonomic Handle
2
On/Off Power Switch
3
Bag Compartment
4
Vacuum Nozzle
5
Headlight
6
Furniture Guard
7
Handle Release Pedal
8
Battery Pack
9
Charge Point
10
Battery Life Display
11
Carry Handle
12
Charger
5 6
4
11
10 9 8
7 12
MATERIAL
FIN
SEE NOTES
DRAWN
DA
AS
ISSUED
DA
SCALE
Assembling the vacuum
Attaching the Handle to the Vacuum
NOTE: Do not turn on the vacuum until it is completely assembled.
The vacuum cleaner and the handle are packed separately and require assembly.
· Remove the handle bracket by removing the two screws (Fig. 1).
· Place handle onto the back of the vacuum, aligning holes with pegs (Fig. 2).
· Place the handle bracket back into position (Fig. 3).
· Secure with two screws removed in Fig 1. Tuck the cord into the space to the left of the handle.
· Open the bag compartment to ensure a vacuum bag is in place.
· Your vacuum is now ready for use.
Charging Battery
The battery is partially charged and will run for a short time. To fully charge the battery see Battery Charging (page 6).
Fig. 1 Fig. 3
Fig. 2
5
Operation
This vacuum is intended for household use only.
Battery Charging
· The battery is located on the back of the vacuum.
· Plug the AC cable into the charger and into a wall socket (Fig. 1).
· Plug the charger DC cable into the Charge Point on the battery. (Fig. 2).
· The Charger LED light will be red during charging and will turn green when the battery pack is fully charged.
Battery Life Display
· Press the button on the battery to illuminate the LED lights.
· When the battery is fully charged there will be four (4) green lights and one (1) red light showing (Fig. 3).
· As the battery is discharged during use the number of green lights showing will reduce from four (4) to none (0).
· When all of the green lights are off and only the red light is showing there is a small amount of time remaining before the battery will be fully discharged and will require recharging.
Reclining the Handle
· Press the Handle Release Pedal located on the back of the vacuum with your foot to recline the handle (Fig. 4).
6
DRAWING SIZE:C PART NUMBER
C223-2000
SHEET 1 OF 1
TACONY CORPORATION CLAIMS PROPRIETARY RIGHTS IN THE MATERIAL DISCLOSED HERE IN. THIS DRAWING IS ISSUED FOR ENGINEERING INFORMATION ONLY. IT MAY NOT BE REPRODUCED, NOR MAY THE INFORMATION HERE IN BE USED FOR MANUFACTURING PURPOSES WITHOUT WRITTEN PERMISSION FROM TACONY CORPORATION.
TACONY CORPORATION 1760 Gilsinn Lane, Fenton, MO 63026
UNLESS OTHERWISE SPECIFIED
X.X .5 mm RADII X.X .5mm X.XX .25mm X.XX .25mm X.XXX .12mm MACHINE SURFACE X.XXXX .012mm BREAK SHARP CORNERS TO .25mm MAX
0 30" COMMON TO BE CONCETRIC TO .05mm
DO NOT SCALE
SCALE 1.000
Fig. 1 Fig. 2 Fig. 3 Fig. 4
BATTERY CHARGER 50.4V DC
FINISH
SEE NOTES DATE
20MAY15 DATE
MATERIAL SEE NOTES
DRAWN
AS ISSUED
DESCRIPTION
MATERIAL
FINISH
SEE NOTES
SEE NOTES
1
DRAWN
DATE
AS
20MAY15
NOTES: 1. OUTPUT 50.4V DC, 1.5A 2. DC POWER CONNECTOR PLUG 2.5MM AND CABLE 47" LONG. 3 INPUT = AC 100-240V, 50/60Hz, 100VA. 4. AC CABLE 71" LONG W/ 2 PIN POLARIZED AMERICAN PLUG 5. PLUGS AND CABLES UL CERTIFIED. 6. CHARGER - UL1310 CERTIFIED
ISSUED SCALE
1.000
DATE X.X X.X X.X
DO NOT SCALE X.X
On/Off Switch
· Turn the switch On to use the vacuum. If the vacuum doesn't turn on, check that the battery is charged (see page 6).
· Always unplug the charger from the Charge Point before use.
Edge Cleaning
The edge cleaning feature provides improved cleaning near walls and stationary furniture. For maximum edge cleaning, place the left side of the nozzle, from the user's perspective, against the wall or stationary furniture (Fig 2).
Automatic Carpet Height Adjustment
Your vacuum is designed with an automatic self-adjusting nozzle. No manual adjustments are required. The height of the nozzle automatically adjusts to the flooring surface. This self-adjusting feature allows the nozzle to float evenly over all flooring surfaces.
Operation
Fig. 1 Fig. 2
7
Operation
Bare Floor Cleaning Your vacuum is equipped with a squeegee on the bottom of the vacuum to improve its effectiveness in cleaning bare floors (Fig. 1).
Vacuuming Under Furniture Your vacuum will lay flat on the floor for effective cleaning under beds and tables. · Press the Handle Release Pedal once for
normal vacuum cleaning (Fig. 2). · Continue to lower the handle to enable the
vacuum to lay flat on the floor (Fig. 3).
Fig. 1
MATERIAL DRAWN ISSUED SCALE
0.250
Fig. 2
Fig. 3
8
MAINTENANCE AND CARE
Replacing the Vacuum Bag
NOTE: Turn the vacuum off and unplug the charger from the Charge Point before changing the bag.
· Unzip the bag compartment.
· Remove the used vacuum bag by pulling the green bag collar tab away from the vacuum (Fig. 1). Slide the used bag out of the bag holder which automatically seals the bag opening (Fig. 2). Discard the used bag.
· To install a new bag, slide the bottom of the green bag collar into the bag holder until it "snaps" into place (Fig. 3).
· Push the top of the bag collar upward until the collar "snaps" into place on the vacuum (Fig. 4).
· Tuck the bag corners into the bag compartment then zip the bag compartment closed.
Fig. 1
Fig. 2
MATERIAL DRAWN ISSUED SCALE
1.000 6
FINISH DATE DATE
DESCRIPTION
.02 IN RADII X.X
±
.02
.01 IN X,XX
±
.01
.005 IN MACHINE SURFACE
.0005 IN BREAK SHARP CORNERS TO .010 MAX
0 ° 30" COMMON
TO BE CONCETRIC TO .002
7
TACONY CORPORATION CLAIMS PROPRIETARY RIGHTS IN THE MATERIAL DISCLOSED HERE IN. THIS DRAWING IS ISSUED FOR ENGINEERING INFORMATION ONLY. IT MAY NOT BE REPRODUCED, NOR MAY THE INFORMATION HERE IN BE USED FOR MANUFACTURING PURPOSES WITHOUT WRITTEN PERMISSION FROM TACONY CORPORATION.
DRAWING SIZE PART NUMBER
SHEET 1 O 8
Fig. 3
9
MATERIAL DRAWN ISSUED SCALE
1.000 6
FINISH DATE DATE
DESCRIPTION
.02 IN RADII X.X
±
.02
.01 IN X,XX
±
.01
.005 IN MACHINE SURFACE
.0005 IN BREAK SHARP CORNERS TO .010 MAX
0 ° 30" COMMON
TO BE CONCETRIC TO .002
7
TACONY CORPORATION CLAIMS PROPRIETARY RIGHTS IN THE MATERIAL DISCLOSED HERE IN. THIS DRAWING IS ISSUED FOR ENGINEERING INFORMATION ONLY. IT MAY NOT BE REPRODUCED, NOR MAY THE INFORMATION HERE IN BE USED FOR MANUFACTURING PURPOSES WITHOUT WRITTEN PERMISSION FROM TACONY CORPORATION.
DRAWING SIZE PART NUMBER
SHEET 1 O 8
Fig. 4
MAINTENANCE AND CARE
Removing and Reinstalling the Battery NOTE: Turn the vacuum Off and unplug the charger from the Charge Point before removing the battery.
· Remove the vacuum bag (see Replacing the Vacuum Bag, page 9).
· Remove the bag mount screws, then remove the bag mount (Fig. 1).
· Remove the bag compartment.
· Remove the battery clamp screws and lift the battery off its connectors (Fig. 2).
· To replace the battery reverse the above steps.
SHEET
PART NUMBER
REV
7 OF 8
DESCRIPTION OF CHANGE
REV
DATE
ECN NO
BY
Fig. 1
MATERIAL
DRAWN
ISSUED
SCALE
0.250
FINISH
TACONY C
DATE
1760 Gilsinn Lane, Fen
UNLESS OTHE
DATE
X.X .5 mm RADII X.X
X.XX .25mm X.XX
X.XXX .12mm MACHINE S
DO NOT SCALE X.XXXX .012mm BREAK SH 0 30" COMMON
Fig. 2
MATERIAL
DRAWN
ISSUED
SCALE
0.250
FINISH
TACONY CORPORATION
DATE
1760 Gilsinn Lane, Fenton, MO 63026
UNLESS OTHERWISE SPECIFIED
DATE
DO NOT SCALE
X.X .5 mm RADII X.X .5mm X.XX .25mm X.XX .25mm X.XXX .12mm MACHINE SURFACE X.XXXX .012mm BREAK SHARP CORNERS TO .25mm MAX
0 30" COMMON TO BE CONCETRIC TO .05mm
DESCRIPTION
TACONY CORPORATION CLAIMS PROPRIETARY RIGHTS IN THE MATERIAL DISCLOSED HERE IN. THIS DRAWING IS ISSUED FOR ENGINEERING INFORMATION ONLY. IT MAY NOT BE REPRODUCED, NOR MAY THE INFORMATION HERE IN BE USED FOR MANUFACTURING PURPOSES WITHOUT WRITTEN PERMISSION FROM TACONY CORPORATION.
DRAWING SIZE:C PART NUMBER
SHEET 7 OF 8
10
MAINTENANCE AND CARE
Removing and Reinstalling the Bottom Plate
WARNING! To Reduce the Risk of Electrical Shock or Injury from Moving Parts, Turn the Vacuum Off and Unplug the Charger from the Charge Point Before Servicing or Cleaning the Vacuum.
To Remove the Bottom Plate:
· Make sure the vacuum is turned Off.
· Remove the battery (see Removing and Reinstalling the Battery, page 10).
· Press the handle release pedal to place the vacuum cleaner in the flat position.
· Turn the vacuum cleaner over, exposing the bottom plate.
· Turn the two screws a quarter turn to release the bottom plate (Fig. 1). Remove the bottom plate.
· To reinstall the bottom plate: Align the front edge of the bottom plate into the notches inside the nozzle (Fig. 2).
· Press the bottom plate into position until the plate "clicks" on both sides. Tighten the two screws a quarter turn to secure the bottom plate.
· Replace the Battery (see see Removing and Reinstalling the Battery, page 10).
Fig. 1 Fig. 2
11
MAINTENANCE AND CARE
Replacing the Vacuum Belt
WARNING! To Reduce the Risk of Electrical Shock or Injury from Moving Parts, Turn the Vacuum Off and Unplug the Charger from the Charge Point Before Servicing or Cleaning the Vacuum.
Note: To ensure maximum cleaning efficiency, the belt should be checked regularly to be sure it is in good condition. Check to see if the belt is stretched, cracked, or if excessive slipping is occurring. Replace if needed.
· Turn the vacuum off and unplug the charger from the Charge Point before changing the belt.
· Remove the battery (see see Removing and Reinstalling the Battery, page 10).
· Remove the bottom plate (see Removing and Reinstalling the Bottom Plate, page 11). SCALE 0.400
· Remove the brushroll and the worn or broken belt from the brushroll pulley and the motor drive shaft.
SCALE 0.400
Fig. 1
· Loop the new belt around the motor drive shaft and the brushroll (Fig. 1).
· Reinstall the brushroll into the nozzle. Turn the brushroll by hand, making sure the belt is not twisted and all rotating parts move smoothly (Fig. 2).
Fig. 2
MATERIAL DRAWN ISSUED SCALE
0.250
· Reinstall the bottom plate (see Removing and Reinstalling the Bottom Plate, page 11).
· Replace the battery (see see Removing and Reinstalling the Battery, page 10).
12
MAINTENANCE AND CARE
Replacing the Squeegee
WARNING! To Reduce the Risk of Electrical Shock or Injury from Moving Parts, Turn the Vacuum Off and Unplug the Charger from the Charge Point Before Servicing or Cleaning the Vacuum.
If your squeegee splits or begins to look worn, simply slide the worn squeegee from its track and slide a new one into the track. If you have trouble installing the new squeegee, please visit an Authorized Simplicity Retailer for help.
Annual Checkup
To keep your vacuum in peak operating condition, it is recommended you bring it to an Authorized Simplicity Retailer for an annual checkup. The retailer will conduct a comprehensive examination to ensure your vacuum is in top operating condition.
MATERIAL DRAWN ISSUED SCALE
0.250
13
Problem Solving Guide
Troubleshooting WARNING! To Reduce the Risk of Electrical Shock or Injury From Moving Parts, Unplug the
Charger from the Charge Pont and remove the Battery Before Servicing or Cleaning the Vacuum.
CAUTION! To Reduce the Risk of Electric Shock, Do Not Handle Charger Plug or Appliance with Wet Hands.
PROBLEM Vacuum won't turn on
POSSIBLE REASON
POSSIBLE SOLUTION
· Battery is fully discharged · Charge battery (page 6)
· Needs service
· Take to Authorized Simplicity Retailer
Vacuum won't pick up or low suction
· Vacuum bag full · Broken belt · Worn brushroll
· Install new bag (page 9) · R eplace belt (page 12) · Replace brushroll (page 12)
Dust escaping from vacuum
· Vacuum bag not installed properly
· Install bag properly. Review bag installation (page 9)
Any other service should be performed by an Authorized Simplicity Vacuum Retailer. To locate your nearest Authorized Retailer, visit our website at www.SimplicityVac.com or call 888-9-SIMPLY.
Key Replacement Parts
· Genuine HEPA Media Vacuum Bags: SLH-6 · Genuine Vacuum Belts: S10B-2
For Best Performance
· Keep your vacuum clean and in good operating condition. · Change the vacuum bag once a month or when the bag is 2/3 full to maximize
cleaning performance. · Always use genuine vacuum bags and replacement parts. Use of other products may
result in poor cleaning performance, potential vacuum cleaner damage and may void vacuum warranty. Genuine products are designed for maximum cleaning performance. · Have your vacuum checked annually by your Authorized Simplicity Retailer. · Store your vacuum carefully in a dry area. · For optimum cleaning performance and safety, follow your owner's manual instructions.
14
Warranty
What is Covered: This warranty covers any defects in material and workmanship in your new Simplicity vacuum and applies exclusively to the original purchaser.
How Long Coverage Lasts: Warranty coverage for S10CV lasts four years EXCEPT for the battery which has a warranty that lasts two years. What is Not Covered: · Damage to the vacuum which occurs from neglect, abuse, alterations, accident, misuse
or improper m aintenance. · Normal replacement items: disposable bags and belts.
What We Will Do: This warranty provides, at no cost to you, all labor and parts to keep this vacuum in correct o perating condition during the warranted period.
How to Get Service: Warranty service can only be obtained by presenting the vacuum to an Authorized Simplicity Retailer. A proof-of-purchase and product serial number will be required before service is rendered. To locate your nearest service center, please call 1-888-9-SIMPLY or visit www.SimplicityVac.com.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES WHETHER WRITTEN, ORAL, EXPRESSED OR IMPLIED, (INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE). THIS WARRANTY DISCLAIMS LIABILITY FOR INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
How State Law Applies: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Register your warranty online at www.SimplicityVac.com
15
Owner's Warranty Information
keep this for your records... Date of purchase Serial number Model number
Purchased from: Store name Address City, State, Zip Telephone
16
17
www.SimplicityVac.com
©2015 Tacony Corporation
B503-3200 9.15
Adobe PDF Library 10.0.1 Adobe InDesign CS6 (Macintosh) Related Documents
Simplicity S65S, S65D, S65P Owner's Manual: Operation and Maintenance Guide
Simplicity Scout Plus Vacuum Cleaner Owner's Manual: Operation & Maintenance Guide
Simplicity S60 Spiffy Owner's Manual
Simplicity BRIO Canister Vacuum Owner's Manual
Simplicity S65, S65D, S65P, S65S Vacuum Parts Book
Simplicity Model 725 & 700 Riding Tractors Owner's Manual and Parts List
Simplicity S60 Bagless Broom Parts Book
Simplicity Broadmoor Series Riding Mower Operator's Manual
