ONKRON N1L Tilt Swivel Ceiling TV Mount
Model: N1L
Product Overview
The ONKRON N1L is a versatile tilt and swivel ceiling TV mount designed to securely hold televisions and monitors. It offers flexible viewing angles and adjustable height for optimal placement.
Key Specifications:
- Screen Size: 32" - 80"
- Tilt Angle: -5° to +15°
- Swivel Angle: 60°
- Load Capacity: 68.2 kg (150 lbs)
- Height Adjustment Range: 717 mm - 1584 mm (28 ¼" - 62 ⅜")
- VESA Compatibility: 100x100 mm up to 600x400 mm
This document provides installation instructions and safety guidelines. Please read thoroughly before proceeding.
Important Safety Information & Warnings
CAUTION: Please read all instructions and safety guidelines before assembly. Failure to do so may cause injury, product damage, and additional material damage.
- Always wear suitable personal protective equipment and use the correct tools for safe installation.
- DO NOT exceed the maximum permissible weight of the unit.
- DO NOT make non-factory approved modifications.
- DO NOT use the unit outside of its factory approved purpose.
- DO NOT OVERTIGHTEN assembly screws.
- Use only the factory-provided mounting screws.
- Ensure the mounting surface has structural integrity capable of supporting the total weight of the unit and all attached equipment.
- Pay attention to the working environment, which may cause accidental damage (e.g., foot traffic, falling objects).
- Keep children away from assembly hardware; small parts can cause choking if swallowed.
- Ensure the mounting surface materials are strong enough to withstand the installed product and equipment.
- Using the product with devices exceeding the maximum weight limit can lead to malfunction, complete failure, and user injury.
- Incorrect installation can cause serious harm to the user's health.
- Professional installation is recommended.
- Ensure the work surface can support the combined weight of the product, device, and any additional components.
- Product contains small parts that can cause choking if swallowed; keep out of reach of children.
- Improper use can lead to product damage and injury.
- Verify screen compatibility (VESA, weight, diagonal) before installation.
- Installation of an incompatible screen may cause damage and injury.
- ATTENTION: Installation on drywall, hollow brick, or aerated concrete walls is forbidden.
- ATTENTION! For safety, two people should participate in the installation and adjustment of the TV.
Parts List
Mounting Bracket (x1)
VESA Panel (x1)
Pole Section (x1)
Pole Section (x1)
Pole Section (x1)
Protective Pad (x4)
Rail (x2)
Rail (x2)
Nut M8 (x7)
Washer 18x8.2x1.5 (x10)
Screw M6x8 (x8)
Washer 18x8.2x1 (x2)
Washer 13x6x1.5 (x4)
Screw M5x15 (x4)
Screw M6x15 (x4)
Screw M8x15 (x4)
Screw M8x15 (x2)
Screw M8x60 (x3)
Screw M8x55 (x4)
Allen Key S6 (x1)
Screw M8/10x80 (x6)
Screw 7x80 (x6)
Screw Ø7 (x6)
Nut 12mm (x6)
Nut 13mm (x6)
Installation Instructions
Step 1: Ceiling Mounting Options
Choose the desired mounting height. The mount offers two primary height configurations:
- Short configuration: 1005 mm (39 ⅝")
- Long configuration: 1584 mm (62 ⅜")
Diagram Description: Two vertical poles are shown. The left pole is shorter, indicating the 1005 mm configuration, with a TV bracket attached. The right pole is longer, indicating the 1584 mm configuration, also with a TV bracket. Plus signs (+) suggest additional pole sections can be added to achieve the longer height.
Step 2: Pole Assembly (Two-tube and Three-tube)
Assemble the main support pole by connecting the pole sections (T1, T2, T3) using nuts (A) and washers (B or D), and screws (I or J). The specific combination of pole sections and hardware depends on the desired height and configuration.
Diagram Description (Two-tube): Shows the assembly of two pole sections (T2 and T3). Part CP (mounting bracket) is attached to the top of T2 using nuts (A) and screws (I). An Allen key (K) is used for tightening.
Diagram Description (Two-tube, alternative): Shows the assembly of two pole sections (T2 and T3). Part CP is attached to the top of T3 using nuts (A) and screws (J). An Allen key (K) is used for tightening.
Diagram Description (Three-tube): Shows the assembly of three pole sections (T1, T2, T3). Part CP is attached to the top of T1 using nuts (A) and screws (I). An Allen key (K) is used for tightening. Washers (B) are used in conjunction with screws.
Diagram Description (Three-tube, alternative): Shows the assembly of three pole sections (T2 and T3). Part CP is attached to the top of T3 using nuts (A) and screws (J). An Allen key (K) is used for tightening. Washers (B) are used in conjunction with screws.
Step 3: Installation on Ceiling
This step details attaching the assembled pole structure to the ceiling. Two methods are shown: for wooden ceilings and for concrete ceilings.
3a: Installation on a Wooden Ceiling
Diagram Description: Shows the mounting bracket (CP) being attached to a wooden ceiling beam. Pilot holes are drilled using a drill and a Ø4 mm (5/32") drill bit. Screws are inserted into the ceiling. The diagram indicates a minimum wood thickness of 70 mm (2 ¾"). A checkmark (✔️) indicates correct installation, while a cross (❌) indicates incorrect placement.
3b: Installation on a Concrete Ceiling
Diagram Description: Shows the mounting bracket (CP) being attached to a concrete ceiling. Holes are drilled using a drill and a Ø12 mm (½") drill bit. Anchors are inserted into the holes, followed by screws. The diagram indicates a minimum concrete thickness of 90 mm (3 ½").
3c: Securing the Mount (Concrete/Hollow Walls)
For concrete ceilings, use screws (M) with washers (N) and nuts (P1). For hollow brick or other specific surfaces, use screws (L) with nuts (P2).
Diagram Description (Concrete): Shows the mounting bracket (CP) being secured to the ceiling using screws (M), washers (N), and nuts (P1). An Allen key and wrench are shown for tightening.
Diagram Description (Hollow Brick/Other): Shows the mounting bracket (CP) being secured using screws (L) and nuts (P2).
ATTENTION: Installation on drywall, hollow brick, or aerated concrete walls is forbidden.
ATTENTION! Two people should participate in the installation and adjustment of the TV.
Step 4: Wall Mounting Options
This section illustrates different height options for wall mounting the bracket.
- Short configuration: 717 mm (28 ¼")
- Medium configuration: 1005 mm (39 ⅝")
- Long configuration: 1584 mm (62 ⅜")
Diagram Description: Shows three vertical wall mount configurations with varying lengths, indicating different height settings for the TV bracket.
Step 5: Stud Wall Installation
This step describes attaching the mounting bracket (CP) to a wooden stud wall.
Diagram Description: Shows the mounting bracket (CP) being attached to a wooden stud wall. Pilot holes are drilled using a drill and a Ø4 mm (5/32") drill bit. Screws are inserted into the studs. The diagram indicates a minimum wood thickness of 70 mm (2 ¾"). A checkmark (✔️) indicates correct installation, while a cross (❌) indicates incorrect placement.
Step 6: Concrete Wall Installation
This step describes attaching the mounting bracket (CP) to a concrete wall.
Diagram Description: Shows the mounting bracket (CP) being attached to a concrete wall. Holes are drilled using a drill and a Ø12 mm (½") drill bit. Anchors are inserted into the holes, followed by screws. The diagram indicates a minimum concrete thickness of 90 mm (3 ½").
Step 7: Securing Wall Mounts
Details on securing the mounting bracket (CP) to different wall types.
7a: Securing to Stud/Wooden Walls
Use screws (M) with washers (N) and nuts (P1).
Diagram Description: Shows the mounting bracket (CP) being secured to a wall using screws (M), washers (N), and nuts (P1). An Allen key and wrench are shown for tightening.
7b: Securing to Concrete/Hollow Walls
Use screws (L) with nuts (P2).
Diagram Description: Shows the mounting bracket (CP) being secured using screws (L) and nuts (P2).
ATTENTION: Installation on drywall, hollow brick, or aerated concrete walls is forbidden.
ATTENTION! Two people should participate in the installation and adjustment of the TV.
Step 8: VESA Panel Assembly (with Rails)
Assemble the VESA plate with rails (VP, VA, HA) using screws (C).
Diagram Description: Shows the VESA panel (VP) being attached to two rails (VA and HA) using screws (C). An Allen key is shown for tightening.
Step 9: Installation of Protective Pads
Attach protective pads (PP) to the VESA panel (VP).
Purpose: The pads improve scratch resistance and reduce vibration.
Diagram Description: Shows protective pads (PP) being placed into designated holes on the VESA panel (VP). The diagram indicates that these pads are for scratch protection and vibration reduction.
Step 10: Installation of the VESA-panel onto the TV
Attach the assembled VESA panel to the back of the TV using appropriate screws and washers.
VESA Patterns Supported: 100x100, 100x200, 200x100, 200x200, 200x300, 200x400, 300x100, 300x200, 300x300, 300x400, 400x200, 400x300, 400x400, 500x400, 600x200, 600x300, 600x400.
Screws Provided: M5x15 (E), M6x15 (F), M8x15 (G), M8x50 (G).
Diagram Description: Shows the VESA panel (VP) being attached to the back of a TV. Screws (E, F, G) and washers (E1) are used. The diagram highlights the selection of appropriate screws based on the TV's VESA holes and the need for secure tightening without overtightening.
ATTENTION! All screws must be securely tightened. DO NOT OVERTIGHTEN THEM!
Step 11: TV Mounting
Mount the TV with the attached VESA panel onto the main ceiling/wall mount.
Diagram Description: Shows the TV with the VESA panel being attached to the main vertical pole of the mount. Nuts (A) and screws (I) are used, secured with an Allen key (K).
Step 12: Tilt Angle Adjustment and Fixation
Adjust the tilt angle of the TV and secure the screws.
The TV can be tilted from -5° to +15°.
Diagram Description: Shows a close-up of the tilt adjustment mechanism. Screws (H) and washers (D) are used to set the tilt angle. An Allen key (K) is used for tightening. The diagram illustrates the range of motion from -5° to +15°.
Step 13: Possible VESA Patterns and Sizes
Illustrates various VESA mounting hole patterns and their dimensions supported by the mount.
Diagram Description: Displays six different VESA mounting configurations with dimensions ranging from 100x100 mm up to 600x400 mm, showing how the mounting arms can be positioned.
Step 14: VESA Assembly with Rails
This step details assembling the VESA plate with rails.
Diagram Description: Shows the VESA panel (VP) being attached to rails (VA, HA) using screws (C). This appears to be an alternative or supplementary assembly method for the VESA plate.
Step 15: Installation of Protective Pads (VESA Panel)
Attach protective pads (PP) to the VESA panel.
Supported VESA Patterns: 200x300, 200x400, 300x100, 300x200, 300x300, 300x400, 400x200, 400x300, 400x400, 500x400, 600x200, 600x300, 600x400.
Purpose: The pads are designed to improve scratch resistance and reduce vibration.
Diagram Description: Shows protective pads (PP) being placed into designated holes on the VESA panel. This step reiterates the purpose of the pads for scratch and vibration protection.
Step 16: Installation of the VESA-panel onto the TV (Reiteration)
This step reiterates the process of attaching the VESA panel to the TV, using screws (E, F, G) and washers.
Diagram Description: Similar to Step 10, this shows the VESA panel being attached to a TV using screws and washers, emphasizing secure tightening.
ATTENTION! All screws must be securely tightened. DO NOT OVERTIGHTEN THEM!
Step 17: TV Mounting (Reiteration)
This step reiterates the process of mounting the TV onto the main bracket.
Diagram Description: Similar to Step 11, this shows the TV with the VESA panel being attached to the main vertical pole of the mount using nuts (A) and screws (I).
Step 18: Tilt Angle Adjustment and Fixation (Reiteration)
This step reiterates the process of adjusting the tilt angle and securing the screws.
Diagram Description: Similar to Step 12, this shows the tilt adjustment mechanism using screws (H) and washers (D), secured with an Allen key (K), allowing for tilt adjustment between -5° and +15°.
Warranty and Contact Information
Warranty: Not subject to mandatory certification. Unlimited lifespan. 5 YEARS WARRANTY.
For any questions, issues, or safety concerns, please contact the ONKRON customer service team:
- USA: info@onkron.us / +13159682278
- United Kingdom (UK): support@onkron.co.uk / +442045772866
- Europe: info@onkron.de / +494029996807
- Italy: italy@onkron.com / +393894362373
- France: france@bmggcorp.com / +330970467319
- Spain: info@onkron.es / +494029996807
- Poland: onkrontechnologies@gmail.com / +494029996807
- Czech Republic: onkrontechnologies@gmail.com / +494029996807
- Slovakia: onkrontechnologies@gmail.com / +494029996807
- Slovenia: onkrontechnologies@gmail.com / +494029996807
- Russia: support@onkron.ru / +78007772176
For more information, visit:
- www.onkron.us
- www.onkron.de
- www.onkron-uk.co.uk
- www.onkron.ru
