MOES Water Timer Instruction Manual

Product Description

The water valve is a control component in the fluid transportation system, functioning as a shut-off, regulation, diversion, prevention of backflow, pressure stabilization, and overflow pressure relief. Water valves can control the flow of various fluids such as water, steam, oil, gas, slurry, corrosive media, liquid metals, and radioactive fluids.

Warnings

Do not disassemble, reassemble, modify, or attempt to repair this product yourself. This work should be performed by authorized professionals.

Product Overview

The MOES Water Timer features a large screen for displaying information, a control dial with various settings, and several buttons for operation. It connects to a hose tap and controls water flow to two separate zones.

Key components:

• Large Screen: Displays current time, settings, and status indicators like battery level.
• Dial: Used to navigate and select different functions such as OFF, AUTO, Clock, Start Time, How Long, and How Often.
• Buttons:
  • [+] Button: Increases values or advances settings.
  • [-] Button: Decreases values or rewinds settings.
  • [OK] Button: Confirms selections, switches between hours/minutes, or starts/stops operations.
  • [ZONE] Button: Selects between Zone 1 and Zone 2 for programming.
• Filter: Located at the top connection to the hose tap.
• Hose Tap Connection: Connects the timer to the water source.
• Zone 1 Outlet: For connecting a hose to the first watering zone.
• Zone 2 Outlet: For connecting a hose to the second watering zone.

Specifications

Product Installation

1. Installing the Battery

1. Remove the battery cover on the back of the timer.

2. Install 2 new AA (1.5V) alkaline batteries (not included).

3. Firmly reinstall the cover back into the timer.

2. Installing the Timer

1. Attach the timer to an outdoor hose faucet.

2. Turn on the tap after programming the timer.

Automatic Watering Program Setting

1. Set Clock

1. Turn the dial to the SET CLOCK position.

2. Use the [+] and [-] buttons to set the current hour and minutes.

3. Use the [OK] button to switch between setting the hour and the minutes.

4. Turn the dial to save changes.

2. Set Start Time

1. Turn the dial to the START TIME position.

2. Press the [ZONE] button to switch between Zone 1 and Zone 2.

3. Use the [+] and [-] buttons to set the desired start hour and minutes.

4. Use the [OK] button to switch between setting the hour and the minutes.

5. Turn the dial to save changes.

Note: If the START TIME is earlier than the current time (NOW), the scheduled task will be executed the next day.

3. Set How Long (Watering Duration)

1. Turn the dial to the HOW LONG position.

2. Press the [ZONE] button to switch between Zone 1 and Zone 2.

3. Use the [+] and [-] buttons to set the watering duration (from 0 minutes to 5 hours 59 minutes).

4. Use the [OK] button to switch between setting the hours and minutes.

5. Turn the dial to save changes.

Note: If HOW LONG is set to 0 minutes, the scheduled task will not be executed.

4. Set How Often (Watering Frequency)

1. Turn the dial to the HOW OFTEN position.

2. Press the [ZONE] button to switch between Zone 1 and Zone 2.

3. Use the [+] and [-] buttons to set the watering frequency (hours or days).

4. Turn the dial to save changes.

You can choose to water every 1 to 23 hours, or every 1 to 7 days.

Examples of watering frequencies:

• Every 1 day: Mon, Tue, Wed, Thu, Fri, Sat, Sun
• Every 2 days: Mon, Tue, Wed, Thu, Fri, Sat, Sun
• Every 3 days: Mon, Tue, Wed, Thu, Fri, Sat, Sun

5. Auto Mode

Turn the dial to AUTO. The watering plan will be executed automatically. The display will show the current day and time, followed by the next watering plan.

Note: If HOW LONG is set to 0 minutes, the NEXT display will show OFF.

6. OFF Mode

Turn the dial to OFF. The screen will show OFF and the battery level. All programs are saved, and the timer stops working.

Additional Features

Manual Watering

Ensure the timer is in AUTO mode.

1. Press the [OK] button and then use [+] or [-] to select watering duration from 0 to 59 minutes.

2. Press the [ZONE] button to switch between Zone 1 and Zone 2.

3. Press the [OK] button to start watering.

4. Pressing the [OK] button again will end the manual watering task, even if it is currently watering, and the timer will switch back to Auto mode.

For Zone 1 only: Set Zone 2 duration to 0 minutes.

For Zone 2 only: Set Zone 1 duration to 0 minutes.

Rain Delay

Ensure the timer is in AUTO mode.

1. Press and hold the [+] button for 5 seconds until the ☁️ (rain cloud) icon appears on the screen.

2. Use the [+] or [-] buttons to set the delay duration from 0 to 7 days.

3. Press the [OK] button to save changes.

4. To quit Rain Delay, press and hold the [+] button for 5 seconds again.

Child Lock

Ensure the timer is in AUTO mode.

Press and hold the [-] button for 5 seconds until the ? (lock) icon appears on the screen. To cancel the lock, press and hold the [-] button for 5 seconds again.

Battery Status

Battery status is displayed as:

• ? FULL
• ? LOW BATTERY

Note: When the low battery indicator appears, the valve will automatically close to prevent leakage. Replace the battery promptly to ensure normal operation.

Troubleshooting

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Recycling Information

All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19 / EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.

[Recycling symbols]

Warranty Instructions

Thank you for purchasing the product. The warranty is granted as follows:

As a condition of using the warranty, you must comply with the following terms and procedures:

1. Products are covered by a 24-month warranty, effective from the date of purchase.
2. To exercise warranty rights, the purchaser must present: a) Warranty card, b) Proof of purchase (VAT invoice, financial receipt, or other document confirming the actual date of purchase), unless the purchase date is on the warranty card.
3. If product quality problems occur within 24 months from the date of receipt, prepare the product and packaging and go to the place or store where you purchased it for after-sales maintenance. A maintenance fee will be charged if the product is damaged due to personal reasons.
4. It is recommended to protect the goods properly during delivery using original packaging with padding. If using replacement packaging, ensure adequate protection and consider an impact warning sticker (e.g., "Warning Glass").
5. Reported defects covered by the warranty will be considered within 14 days from the date of delivery of the goods to the Guarantor.
6. After checking and determining the legality of the warranty claim, the Guarantor's services will repair the product within a reasonable time, not exceeding 30 days from the date of delivery of the goods. This deadline may extend if hard-to-find spare parts are required.
7. The warranty does not cover performance of maintenance or similar operations specified in the user manual; users are obliged to do these themselves.
8. Defects due to natural wear and tear during use are not covered.
9. The warranty does not cover: a) Mechanical damage caused by the user's fault and resulting product defects. b) Damage caused by improper use of the product.
10. Rights under the guarantee expire in the following circumstances: a) Removal of the warranty seal. b) Removal of the serial number. c) Attempts to eliminate physical defects outside of authorized service. d) Use of non-original parts and consumables.

Warranty Card

Product Information:

• Product Name: __________
• Product Type: __________
• Purchase Date: __________
• Warranty Period: __________
• Dealer Information: __________
• Customer's Name: __________
• Customer Phone: __________
• Customer Address: __________

Maintenance Records:

Contact & Follow Us

Thank you for your support. For any needs, please contact us.

Follow us on:

• Facebook: @moessmart
• YouTube: MOES.Official
• Instagram: @moessmart
• TikTok: @moes_smart
• Website: www.moes.net

Representatives & Manufacturer

UK Representative: EVATOST CONSULTING LTD, Address: Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales, CF15 7QR, Tel: +44-292-1680945, Email: contact@evatmaster.com

EU Representative: AMZLAB GmbH, Laubenhof 23, ESSEN 45326, Email: info@amz-lab.de, Tel: +491745298066, Made In China

Manufacturer: WENZHOU NOVA NEW ENERGY CO.,LTD, Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China, Tel: +86-577-57186815, After-sale Service: service@moeshouse.com