Signature Design by Ashley D677-01 Chair Assembly Instructions
Important Safety Notice
[warning-triangle] IMPORTANT SAFETY NOTICE: READ CAREFULLY BEFORE BEGINNING ASSEMBLY!
- Always use proper tools.
- Follow the assembly steps in order. Do not skip any steps.
- Be sure to check all packing materials carefully for small parts may have come loose inside the carton during shipment. If parts are missing, contact the retailer from which you purchased the product to obtain any missing parts. DO NOT USE SUBSTITUTE PARTS.
- Periodically check to ensure that all connectors (bolts, screws, etc.) are tight.
- Keep the instructions for future reference.
- Some assembly may involve attaching glass or mirrors. Be very careful handling the glass or mirrors, as severe injury may result if the glass or mirror breaks. Never handle large pieces of glass or mirrors by yourself.
- When assembling products that have electric cords (lamps, light, etc.), always (1) make sure the electrical cord is unplugged before assembly and (2) be careful not to twist the electrical cord during assembly.
- When assembling shelves or entertainment centers, do not stand on lower shelves in order to assemble upper shelves-use a step ladder.
- Do not stand on tables, including but not limited to, end tables, coffee tables, and dinner tables, as tables are not to support the weight of a person.
- Where assembly instructions state that the assembly requires two or more people, do not attempt by yourself as there is a risk of injury.
[note] NOTE: ASHLEY FURNITURE INDUSTRIES, LLC. DISCLAIMS ANY LIABILITY FOR DAMAGES OR INJURIES WHICH MAY OCCUR DUE TO FAILURE TO PROPERLY FOLLOW ASSEMBLY INSTRUCTIONS, PROPERLY ASSEMBLE THE PRODUCT, OR PROPERLY USE THE PRODUCT.
[note] NOTE: YOUR UNIT MAY LOOK DIFFERENT IN APPEARANCE FROM THE ONE SHOWN IN THE ILLUSTRATIONS ON THIS INSTRUCTION SHEET.
[note] NOTICIA IMPORTANTE DE SEGURIDAD: LEA CUIDADOSAMENTE ANTES DE COMENZAR A ENSAMBLAR
[note] REMARQUE IMPORTANTE CONCERNANT LA SECURITÉ: LIRE ATTENTIVEMENT AVANT DE COMMENCER LE MONTAGE!
[note] 重要安全提示:组装家具前请仔细阅读以下指南!
Parts List
| Part | Description | Quantity |
|---|---|---|
| A | Chair Back and Seat Frame | x 1 |
| B | Seat Cushion | x 1 |
| C | Legs | x 2 |
| D | Bolt (5/16"x38mm) | x 2 |
| E | Bolt (5/16"x50mm) | x 4 |
| F | Bolt (5/16"x75mm) | x 4 |
| G | Allen Wrench (4mm) | x 1 |
Assembly Steps
[note] NOTE: UNIT SHOULD BE ASSEMBLED BY TWO OR MORE PEOPLE. DO NOT TIGHTEN ANY BOLTS UNTIL ALL BOLTS HAVE BEEN STARTED!
[note] NOTA: ¡ESTA UNIDAD DEBE SER ARMADA POR 2 O MAS PERSONAS! NO APRIETE NINGUN PERNO HASTA QUE TODOS ESTEN EN SU LUGAR!
[note] REMARQUE: LE MEUBLE DOIT ETRE ASSEMBLÉ PAR DEUX PERSONNES OU PLUS. NE BLOQUER AUCUNE VIS TANT QUE VOUS N'AVEZ PAS COMMENCE A TOUTES LES DEMARRER!
[note] 注意:产品应由两个或者两个以上的人员组装。在产品组装过程中,不要锁紧螺栓!
Step 1
The diagram shows part A (chair back and seat frame) upside down. Two legs (C) are shown being attached to the bottom of part A. A zoomed-in view shows that for these two legs, two bolts D (5/16"x38mm) and two bolts F (5/16"x75mm) are used. Part G (allen wrench) is also shown.
Step 2
The diagram shows the chair frame (A) with two legs (C) already attached. The remaining two legs (C) are attached to the frame (A) using two bolts F (5/16"x75mm). A zoomed-in view shows the connection points for these bolts.
Step 3
The diagram shows the seat cushion (B) being attached to the assembled frame and legs. Four bolts E (5/16"x50mm) are used to secure the cushion from underneath, using the allen wrench (G). A zoomed-in view shows the connection points for these bolts.
Step 4
[note] NOTE: Level the chair and tighten all bolts with the allen wrench.
[note] NOTA: Nivele la silla y aprete todos los pernos con la llave allen.
[note] REMARQUE: Mettez la chaise droite et serrez tous les boulons avec les clés allen.
[note] 注意:如果发现椅子不稳,请用内六角扳手拧紧所有螺杆。
The final diagram shows the fully assembled chair. The instruction is to level the chair and tighten all bolts with the allen wrench (G).
