SWISS WATCHES SINCE 1853*
Analogue Mechanical Watches
User's Manual
Display and Functions
The watch face includes the following components:
- 1. Seconds hand
- 2. Minute hand
- 3. Hour hand
- 4. Date*
- 5. Day*
* According to model
Models with a Screwed Crown
- IA. Initial position (screwed down, not pulled out)
- IB. Winding position (unscrewed, not pulled out)
Congratulations
Tissot congratulates you on choosing a TISSOT® watch, a renowned Swiss brand. Meticulously designed with high-quality materials, your watch is protected against shocks, impacts, temperature variations, water, and dust. For optimal precision over many years, please follow the advice provided in this manual.
This user manual applies to all TISSOT® mechanical watches (hand-wound or automatic). Refer to specific explanations for your watch model.
Winding
Models with Screwed Crown
For enhanced water resistance, some models feature a screwed crown. Before setting the time, winding, or date/day, unscrew the crown to position IB. It is crucial to screw the crown back in after each operation to maintain water resistance.
Hand-Wound Mechanical Watches
Hand-wound watches require regular manual winding for continuous operation (e.g., daily before wearing). Pull the crown to position I and turn it forward until it locks. The power reserve for fully wound mechanical movements ranges from 36 to 80 hours, depending on the model.
Automatic Mechanical Watches
If your watch has stopped or has not been worn for several days, manual winding is necessary to ensure continuous operation, especially during periods of low activity. Turn the crown 30 revolutions forward or backward (depending on the model) in position I. The automatic winding system will then maintain the watch's power when worn on the wrist. Automatic watches can also be fully wound manually. Note that automatic movements have a slipping spring that disengages the winding system once fully wound, allowing the crown to turn infinitely. Approximately 80 crown revolutions are usually sufficient for a full wind. The efficiency of the automatic winding system relies on the wearer's wrist movements; avoid deliberately shaking the watch, as this is ineffective and can cause damage.
Settings
Please consider the information regarding screwed crowns when performing settings.
Setting the Time
Pull the crown out to position III and turn it in either direction to set the desired time. On models with a seconds hand, pulling the crown to position III stops the seconds hand, allowing synchronization with an official time signal (radio/TV/Internet). Once synchronized, push the crown back to position I (and screw it back in for models with a screwed crown).
Note: Some calibres lack a "stop seconds" mechanism. To synchronize these, turn the crown slightly backward while holding tension to stop the seconds hand, then release tension when the display matches the time signal.
Rapid Correction of the Date* and Day*
NB: Avoid performing rapid date correction between 22:00 and 02:00.
Pull the crown out to position II. Turn it clockwise to set the date or counterclockwise to set the day. The watch continues to operate during this process, so time adjustment is not required.
Technical Information
Power Reserve
TISSOT® Automatic watches are powered by an oscillating weight that winds the movement through natural wrist movements. They do not require a battery. The power reserve typically ranges from 36 to 80 hours, depending on the model.
Accuracy
The accuracy of a mechanical watch is influenced by the wearer's activity levels. A TISSOT® qualified watchmaker can adjust accuracy within TISSOT® tolerance thresholds. Most watches not certified as chronometers have an average accuracy tolerance of -10/+30 seconds per day. Chronometer-certified watches, tested by COSC (Contrôle Officiel Suisse des Chronomètres), undergo rigorous tests for accuracy in various positions and temperatures, achieving an average accuracy of -4/+6 seconds per day.
Water Resistance
TISSOT® watches are designed to withstand pressures ranging from 3 bar (30 m / 100 ft) to 30 bar (300 m / 1000 ft), as indicated on the case-back. Water resistance is not permanent and can be affected by gasket aging or accidental impacts. It is recommended to have the watch's water resistance checked annually by an approved TISSOT® service centre.
Care and Maintenance
Temperature
Avoid exposing your watch to sudden temperature changes (e.g., sunlight followed by cold water immersion) or extreme temperatures (above 60°C / 140°F or below 0°C / 32°F).
Magnetic Fields
Protect your watch from intense magnetic fields generated by sources such as loudspeakers, mobile phones, computers, refrigerators, and other electromagnetic appliances.
Shocks and Impacts
Prevent thermal shocks and impacts, as they can harm your watch. In case of a violent impact, have your watch inspected by an approved TISSOT® service centre.
Harmful Products
Prevent direct contact with solvents, detergents, perfumes, and cosmetic products, as these can damage the bracelet, case, or gaskets.
Cleaning
Regular cleaning is advised (except for leather straps) using a soft cloth and lukewarm soapy water. After immersion in salt water, rinse the watch in fresh water and allow it to dry completely.
Services
Like any precision instrument, regular servicing is essential for optimal performance. It is recommended to have your watch checked every 3 to 4 years by an approved TISSOT® retailer or service centre. Shorter intervals may be necessary depending on climate and usage conditions. To ensure the highest service standards and maintain warranty validity, always consult an approved TISSOT® retailer or service centre.
Availability of Spare Parts
TISSOT® guarantees the availability of spare parts for a minimum of 10 years for standard watches and up to 20 years for gold watches from the date production ceases. If a specific spare part's production is stopped or deferred, TISSOT® reserves the right, at its sole discretion, to offer an alternative solution to the customer.
