Philips GreenPerform Elite Highbay G2

Product Overview & Certifications

This document provides mounting instructions and technical specifications for the Philips GreenPerform Elite Highbay G2 LED Highbay, model BY778P.

Certifications and Ratings: GB, IEC 60598, IP66, ta 35°C, CE, UKCA, EAC.

This product contains a light source of energy efficiency class: B.

Technical Specifications

Dimensions

Dimensions are provided in millimeters (mm).

Mounting Instructions

Suspension Mounting

Components: Bracket, Safety string.

1. Attach the bracket to the luminaire.
2. Connect the safety cable to the bracket.
3. Secure the safety cable to the mounting point. The safety cable length should be between 'd' and 'd + 30cm', where 'd' is the luminaire installation distance from the ceiling/mounting surface.
4. The luminaire is now suspended.

Note: Safety cable and fixing screws are not provided by Signify and must be arranged by a professional installer. Safety cable material should be robust, not less than SUS304 Ø3.

Pipe Mounting

Components: Pipe (not provided), bracket, washer.

1. Attach the bracket to the luminaire.
2. Insert the pipe into the bracket.
3. Secure the pipe with screws and a tooth washer (torque 20 Nm).
4. The luminaire is now mounted on a pipe.

Note: The pipe is not provided with the luminaire. Ensure the pipe connection is secure (torque 20 Nm).

Bracket Mounting (Option)

Components: Bracket, screws, tooth washer.

1. Attach the bracket to the luminaire.
2. Secure the bracket to the mounting surface using screws and a tooth washer (torque 25 Nm).
3. Connect power and signal cables.
4. The luminaire is now mounted via bracket.

Note: Mounting bracket accessory must be ordered separately.

Power Connection

Power Cable:

• Brown: L (Live)
• Blue: N (Neutral)
• Yellow+Green: GND (Earth)

Cable type: 60245 IEC57 3x1mm².

PSD Signal Cable (Only for PSD models):

• Brown: DALI+
• Blue: DALI-

Cable type: 60245 IEC57 2x1mm².

For PSU and PSD models, the flexible wiring connected to the luminaire must be effectively fixed to the wall if it is within arm's reach to reduce the risk of strangulation.

Insulation between LV mains and control conductors is basic insulation.

Please use an IP66 or above terminal box (minimum dimensions 10x20x25 mm); this is not provided by Signify.

Inrush Current

The following table details the inrush current characteristics for different models.

*Note: The leakage current (touch current or protective conductor current) of the electrical circuit may be greatly dependent upon electrical supply cables used, their rating and length, proper connection of electrical supply cables to luminaires, and wiring connection topology of luminaires to the supply electrical circuit, amongst other site conditions. In some cases referred to as Earth Leakage Current.

Environmental Information & Disposal

RoHS Compliance:

The product contains the following hazardous substances in parts, with 'O' indicating below the limit and 'X' indicating above the limit, according to GB/T 26572:

• LED board/light source: Lead (Pb) O, Mercury (Hg) O, Cadmium (Cd) O, Hexavalent Chromium (Cr(VI)) O, PBB O, PBDE O
• Driver (board), copper and electronic components: Lead (Pb) O, Mercury (Hg) O, Cadmium (Cd) O, Hexavalent Chromium (Cr(VI)) O, PBB O, PBDE X
• Lens optical parts: Lead (Pb) O, Mercury (Hg) O, Cadmium (Cd) O, Hexavalent Chromium (Cr(VI)) O, PBB O, PBDE O
• Housing and other components: Lead (Pb) O, Mercury (Hg) O, Cadmium (Cd) O, Hexavalent Chromium (Cr(VI)) O, PBB O, PBDE O

Disposal Instructions: Please inform yourself about the local waste disposal, separation, and collection system for electrical and electronic products and packaging. Act according to your local rules and do not dispose of old products and packaging with normal household waste. The correct disposal of packaging, your product, and/or batteries will help prevent potential negative consequences for the environment and human health. Batteries should be disposed of separately from the municipal waste stream via designated collection facilities. Non-user replaceable batteries shall be removed by a professional.

General Safety Warnings

• ⚠️ The luminaire shall be installed by a qualified electrician and wired in accordance with the latest IEE electrical regulations or national requirements.
• ⚠️ Turn power off before inspection, installation, or removal.
• ⚠️ Earthing is required before use and must be maintained throughout the product's life.
• ⚠️ Use the luminaire only within applicable product specifications, installation instructions, and environmental conditions for storage and operation.
• ⚠️ Avoid corrosive atmospheres or hazardous materials such as sulfur, chlorine, phthalate, etc., during use and storage.
• ⚠️ The manufacturer is not responsible for damage caused by improper use or self-modifications of the product.
• ⚠️ If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or their service agent or a similar qualified person to avoid a hazard.
• ⚠️ For indoor use only. Not suitable for cold storage areas with significant temperature gradients (e.g., near ventilation openings or doors).
• ⚠️ Recommended mounting height: luminous surface to ground > 5m; luminaire bottom to mounting surface > 0.3m.
• ⚠️ Not suitable for applications like floodlights or tunnel luminaires, or in environments with harsh vibration or extreme winds.
• ⚠️ Periodic cleaning of the optical lens cover with a dry soft cloth is recommended for maximum optical efficiency.
• ⚠️ The light source and control gear contained in this luminaire shall only be replaced by the manufacturer or their service agent or a similar qualified person.