ULINE H-7605 Monitor Arm
Contact: 1-800-295-5510 | uline.com
? For Spanish, see pages 3-4. For French, consult pages 5-6.
Tools Needed
- Electric Drill ड्रिल
- 7/16" Drill Bit
- Phillips Head Drill Bit
- Phillips Screwdriver ?
- Allen Wrench (included) ?
- 10 mm Wrench ?
Hardware
- M6 x 35 mm Allen Head Bolt x 2
- M6 x 50 mm Allen Head Bolt x 2
- Flange Nut x 2 ?
- 6.4 x 18 mm Washer x 2 ⚪
- Small Phillips Head Bolt x 8
- Large Phillips Head Bolt x 8
- 5.3 x 14 mm Washer x 4 ⚪
Installation
? Note: Monitor arm includes hardware to attach to wall or ULINE Deluxe Workstations and Packing Stations.
Upright Mounting
1. Align monitor arm mounting bracket with upright at desired height.
2. Secure to upright with two M6 x 35 mm or M6 x 50 mm Allen head bolts, two 6.4 x 18 mm washers and two hex nuts using an Allen wrench and 10 mm wrench. (See Figure 1)
? Figure 1 Description: Shows attaching the monitor arm mounting bracket to an upright using Allen head bolts and washers.
Wall Mounting
Hardware for Wall Mounting
- ST 5.5 x 60 mm Hex Screw x 2 ?
- 6.4 x 12 mm Washer x 2 ⚪
- Plastic Anchor x 2
1. Align monitor arm mounting bracket with wall at desired height. Mark holes where screws are to be located. Drill holes using 7/16" drill bit. (See Figure 2)
2. Insert plastic anchors into predrilled holes.
3. Position mounting bracket over holes with anchors. Fasten bracket to wall with two 6.4 x 12 mm washers and two ST 5.5 x 60 mm hex screws using 10 mm wrench. (See Figure 3)
? Figure 2 Description: Illustrates drilling holes in a wall and inserting plastic anchors.
? Figure 3 Description: Shows attaching the wall bracket using hex screws and washers.
Attaching Monitor
? Note: Ensure monitor has a VESA hole pattern of 100 x 100 mm or 75 x 75 mm. (See Figure 4)
? Note: If monitor is attached to a fixed base, remove monitor from base.
⚠️ CAUTION! Be careful not to scratch screen during installation.
1. Easy-adjust monitor mount includes a built-in counterweight system for free-range motion. Arm in mount may need to be adjusted to allow monitor to stop at desired position. Attach monitor to plate. (See Figure 5)
? Figure 4 Description: Displays VESA mounting hole patterns: 75 x 75 mm or 100 x 100 mm.
? Figure 5 Description: Shows attaching the monitor to the mounting plate using appropriate bolts and washers, with an Allen wrench.
Counterweight Adjustment
1. To adjust the counterweight, use 5 x 5 Allen wrench on screw above middle joint. Turn towards "-" if monitor raises up. Turn towards "+" if monitor lowers. Adjust until mount can be stopped at desired position. (See Figure 6)
? Figure 6 Description: Illustrates adjusting the monitor's swivel and tilt using an Allen wrench, with angle indicators (±180°, -85°~15°, ±90°).
Cable Management
1. To remove covers, use a Phillips head screwdriver to unscrew the two screws securing covers to the monitor arm. This allows user to slide cables through covers. Once complete, re-secure the covers to the monitor arm using the Phillips head screws. (See Figure 7)
? Figure 7 Description: Shows removing covers, inserting cables, and re-securing covers with screws.
