LIVALL Smart Helmet EVO21

Quick Start Guide & Warranty Information

Visit: www.livall.com

I. Introduction

Welcome to the User Guide for LIVALL smart helmets. This Guide will help you better use this product. With continuous improvements of our products, this Guide will be updated from time to time. You can access the latest version and learn more about the helmet on www.livall.com.

Helmet Overview

The helmet features:

• Front Lights
• Chinstrap
• Tension adjuster
• Taillight
• Power Switch ?
• Magnetic USB charging port ?

Note: The illustration is for reference only. The actual product may differ.

II. Packing List

• Smart Helmet x 1
• Quick Start Guide & Warranty Information x 1
• Bling Remote Controller BR80 x 1
• Magnetic USB charging cable x 1

III. Wearing Instructions

Correct vs. Incorrect Fit

Incorrect Fit:

• Helmet positioned too high or too low on the head.
• Straps too loose or not properly adjusted.

Correct Fit:

• Adjust the length of the chinstrap.
• Leave a gap as thick as one finger between the chinstrap and the chin.
• Correctly position the helmet on the head.
• Check whether the buckle is properly fastened ✔️.

IV. Operation Instructions

Turn On Your Helmet

For the first time to use, press the power on button ? located at the back of the helmet. The tail lights illuminating indicate the smart helmet is on.

Note: If it cannot be activated successfully, please charge it and try again.

Battery Status

Remaining battery level is shown by the number of light beads in the middle of the tail, displayed when the helmet is initially turned on. Full battery is indicated when all light beads are on.

Connect the Remote Control BR80 (Control the Turning Signals)

1) First connection

Turn on the BR80. Within a distance of 30cm [approx. 1 foot] between the BR80 and the helmet, it will automatically connect to the helmet.

2) Replacing device (When the original BR80 lost or damaged)

Put the powered-on BR80 close to the helmet's main control. The warning light will flash three times per second, indicating that a BR80 needs to be connected. Press the helmet's power button within 10 seconds to confirm the connection. The tail light will continue to flash in its previous mode. After successful connection, left and right turn signals can be controlled by the BR80.

Note: Turn signals are controlled by the BR80's left (L) and right (R) buttons. Other buttons on the BR80 are not needed for this function.

Automatic Standby

After the helmet powers on and remains stationary for a while, it will enter sleep mode to save power. The tail light will turn off.

Automatic Wake Up

To wake up the helmet, shake it several times until the tail lights illuminate.

Note: If the helmet does not wake up, ensure the battery levels are adequate.

Adaptive lighting

(This feature is enabled by default and can be adjusted via the app.) When the helmet is powered on during the day or in bright conditions, only the central LED light will flash, and other LED lights will turn off. During the night or in dark environments, the entire taillight will flash.

Lighting Mode

After the helmet is turned on, press the power button for one second to switch between three lighting modes.

Brake warning light

When the helmet detects smooth deceleration, the whole taillight will light up for several seconds to warn vehicles behind.

Note: If the helmet shakes heavily, the built-in sensor may detect significant deceleration, causing the warning light to stay on, which is normal.

Connect With Your Phone

1. Download the LIVALL Riding App from your smartphone app store.
2. Turn on Bluetooth ? on your phone and turn on the helmet.
3. In the LIVALL Riding app, tap "Device", then tap "Helmet". Pair the helmet with your phone through the app. After a successful connection, "Helmet" will display "EVO21".

Tip: For a stable Bluetooth connection while riding, use a smartphone holder and place the phone on your handlebars.

SOS Alert (requires connection to LIVALL Riding APP)

The helmet has a fall detection sensor. When a fall is detected, it sends a signal to the LIVALL Riding APP via Bluetooth technology. The APP then sends an SOS message to a pre-arranged emergency contact.

Power off

Hold the power button ? at the back of the helmet for several seconds until all LED taillights turn off.

Charge

Open the soft rubber lid ?️ to reveal the Magnetic charging port ?. Insert a USB cable into the helmet's charging interface. Charging begins when the middle area LEDs light up. Charging is complete when the middle area LEDs stop blinking and turn off.

EVO21 Product Feature List

Kind Reminder: Please refer to the Quick Start Guide for more details about the functions.

V. Considerations

1. The helmet contains electronic parts. Avoid long rides in the rain, though the helmet offers splash protection.
2. If the helmet gets wet, water droplets may appear in the tail LED light chimneys. These will disappear when the helmet is placed in a ventilated environment for 1-2 days.
3. The helmet contains a battery whose capacity varies with temperature. Battery life may decrease at low temperatures or below 0°C.
4. If electronic functions are not working, charge the helmet for 3 hours and check again.
5. The helmet contains impact detection devices. The SOS alert feature is triggered only if you connect your helmet with the LIVALL Riding App and start ride mode. Your designated emergency contacts will receive SOS messages.
6. Cleaning the golden contacts of the charging plug sheet with metal or hard tools (like blades or tweezers) is strictly forbidden. Use cotton swabs with clean water or alcohol. Ensure the charging plug is clean before charging.
7. The built-in battery must not be disassembled, squeezed, heated, or burned. Do not use sharp devices to puncture or pry the battery, as this could cause it to catch fire.
8. Do not place the helmet with sharp objects to avoid damage.

Note: 1. Network anomalies may prevent successful sending or receiving of SOS messages. 2. To maintain battery life, it is recommended to fully charge the helmet before long-term storage (six months to one year).

VI. Technical Specifications

• Charging port: Magnetic USB
• Electricity parameter: DC 5V/1A
• Battery: 3.7V/600mAh
• Charging time: About 3 hours
• Waterproof class: IPX5
• Battery life: About 10 hrs in the default Light Mode
• Temperature: Storage: -20°C ~45°C; Use: 0°C~40°C; Charging: 0°C~40°C

Notes: Data measured by LIVALL in a controlled environment (25°C, specific light patterns). Actual data may vary with environmental conditions. For battery longevity, charge fully before long-term storage.

VII. Electronic functions troubleshooting

If you encounter the following issues, charge the product as per the quick guide (the helmet can be reset during charging). If problems persist, contact after-sales service (email: riding@livall.com).

Faults:

1. Cannot be charged or turned off normally.
2. Helmet turns on, but lights and other functions do not work normally.
3. Helmet turns off automatically shortly after powering on without reason.

Note: Refer to the specific model's quick guide for detailed function information.

Performance standards:

• USA: CPSC1203:1998, FCC Part 15 Rules
• Europe: EN 1078: 2012+A1:2012

VIII. Instructions for Use and Care

1. The helmet provides protection only if it fits well. Choose a size that feels secure and comfortable.
2. Adjust the helmet straps so they do not cover the ears, and position the buckle away from the jawbone. Ensure straps and buckle are comfortable and firm.
3. Position the helmet correctly on the head to ensure intended protection, covering the forehead and not pushed too far back.
4. A helmet cannot always protect against injury.
5. A helmet subjected to a severe impact should be discarded and destroyed.
6. Modifying or removing original component parts is dangerous and not recommended by the manufacturer. Helmets should not be adapted for accessories in ways not recommended by the manufacturer.
7. This device complies with FCC Rules Part 15. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received, including that which may cause undesired operation.
8. Take good care of the product. Do not wash the surface with corrosive solvents or strike the helmet.
9. Validity: Valid for 3 years with no impact and under normal use.

This helmet is in conformity with regulation (EU) 2016/425 and the Personal Protective Equipment (Enforcement) Regulations 2018.

Compliance and Manufacturer Information

LIVALL Tech Co., Ltd. declares that the full EU Declaration of conformity and UK Declaration of conformity are available at www.livall.com/tech/product.html.

Designed and Manufactured in Shenzhen, China

Approved body: ITS Testing Services(UK) Ltd., Centre Court, Meridian Business Park, Leicester LE19 1WD. UKCA AB0362

Notified Body: Telefication B.V. with its office located at Wilmersdorf 50, 7327 AC Apeldoorn, The Netherlands. Notified Body No. 0560

Original Design Manufacturer: LIVALL Tech Co., Ltd.

Address: 904, R&D Building Tsinghua Hi-Tech Park, NanShan, Shenzhen, China

Postal Code: 518057

Website: www.livall.com

Support & Service E-mail: support@livall.com

Model: EVO21-QO-V1.0