Lowrance Eagle® 7 & 9 Installation Guide

In the box

The following items are included:

A: EAGLE 7 or 9 display unit
B: Gimbal kit
C: SplitShot or TripleShot skimmer transducer
D: Power cable kit
E: Cable lock collars
F: Documentation pack

Gimbal mounting

Step 1: Drill recommended pilot holes. For soft/hard materials, use a drill bit size of Ø3.8 - 4.8 mm (3/16").

Illustration showing drilling pilot holes for gimbal mount.

WARNING: Always wear appropriate eyewear, ear protection, and dust mask when drilling, cutting, or sanding. Remember to check the reverse side of all surfaces whenever drilling or cutting.

Step 2: Attach the gimbal bracket to the surface using the provided hardware. The illustration shows a bracket being secured with screws and a drill.

Illustration showing attaching the gimbal bracket.

Step 3: Mount the display unit onto the gimbal bracket and secure it.

Illustration showing the display unit being attached to the gimbal bracket.

Panel mounting

Step 1: Prepare the mounting surface and cut an opening according to the dimensions provided (refer to the dimensions section).

Illustration showing a panel with a cut-out for the display unit.

Step 2: Insert the display unit into the panel opening.

Illustration showing the display unit being inserted into the panel.

Step 3: Secure the display unit from the back of the panel using the provided mounting hardware.

Illustration showing securing the unit from behind the panel.

Step 4: Attach any necessary trim pieces.

Illustration showing a trim piece being attached.

Step 5: Connect cables to the back of the display unit.

Illustration showing cables being connected to the back of the unit.

Step 6: The display unit is now mounted to the panel.

Illustration showing the fully mounted display unit on the panel.

WARNING: Panel mounting may affect GPS performance.

Cable lock collar

Step 1: Prepare the transducer and power cables by attaching the appropriate connectors.

Illustration showing cable connectors being prepared.

Step 2: Secure the cables using the provided cable lock collars.

Illustration showing cable lock collars being applied to the connectors.

Wiring

Connect the transducer and power cables to the display unit. Ensure correct polarity for the power connection (+/-).

Diagram illustrating the wiring connections between the transducer, power source, and the display unit.

Note:

Connect either a SplitShot or TripleShot transducer.
Refer to included transducer installation information.

Dimensions

EAGLE 7

Display Unit Dimensions: Width: 225.9 mm (8.89"), Height: 139.8 mm (5.50"), Depth: 69.2 mm (2.72"). Mounting depth: 121.8 mm (4.80"). Bezel dimensions: 226.5 mm (8.92") wide, 162.8 mm (6.41") high.

Diagram showing the dimensions of the EAGLE 7 display unit.

EAGLE 9

Display Unit Dimensions: Width: 287.2 mm (11.30"), Height: 162.5 mm (6.39"), Depth: 69.1 mm (2.71"). Mounting depth: 120.8 mm (4.75"). Bezel dimensions: 270.7 mm (10.65") wide, 175.2 mm (6.89") high.

Diagram showing the dimensions of the EAGLE 9 display unit.

Technical specifications

Feature	7"	9"
Display Resolution	800 x 480	1024 x 600
Viewing angles (degrees)	85° top/bottom/left/right
Supply voltage	12 V DC (10.8 - 18 V DC)
Power consumption (max)	6.6 W (550 mA at 12 V DC)	7.68 W (640 mA at 12 V DC)
Recommended fuse rating	3 A
Operating temperature range	-15°C to 55°C (5°F to 131°F)
Storage temperature	-20°C to 60°C (-4°F to 140°F)
Waterproof rating	IPX7
Sonar	1 port (SplitShot and TripleShot compatible)
Card reader	1 slot (microSD® 32 GB maximum)
Dimensions	Refer to dimensions section in this document
Weight (display only)	0.67 kg (1.48 lb)	0.9 kg (1.98 lb)
Mounting type	Panel mount or gimbal mount

Accessories

The following accessories are sold separately and available from your local retailer:

Item	7"	9"
Suncover	000-16250-001	000-16251-001
Dash gasket kit	000-16254-001	000-16255-001

Trademarks

®Reg. U.S. Pat. & Tm. Off, and ™ common law marks. Visit www.navico.com/intellectual-property to review the global trademark rights and accreditations for Navico Group and other entities.

Navico® is a trademark of Navico Group.
Lowrance® is a trademark of Navico Group.
EAGLE® is a trademark of Navico Group.
SD® and microSD® are trademarks of SD-3C, LLC.

For more information, visit www.lowrance.com

	Lowrance Eagle 7 & 9 Installation Guide This guide provides instructions for installing the Lowrance Eagle 7 and 9 display units, including gimbal and panel mounting, wiring, and technical specifications.
	Lowrance Eagle 7 & 9 Installation Guide Installation guide for the Lowrance Eagle 7 and 9 series fishfinders, covering gimbal and panel mounting, wiring, dimensions, and technical specifications.
	Lowrance Eagle Series Operator Manual Comprehensive operator manual for the Lowrance Eagle Series fishfinders, covering basic operation, customization, charts, navigation, sonar, structure mapping, alarms, tools, maintenance, and simulator functions.
	Lowrance Eagle Quick Start Guide A quick start guide for the Lowrance Eagle multi-function display (MFD), covering physical controls, system controls, chart navigation, waypoint management, route creation, and sonar functionalities like Sonar, SideScan, and DownScan.
	Lowrance Eagle 5 Installation Guide and Mounting Template This document provides installation instructions and a mounting template for the Lowrance Eagle 5 fishfinder/chartplotter. It includes technical specifications, in-the-box contents, mounting procedures, and accessory information.
	Lowrance Eagle Series Operator Manual: Your Guide to Advanced Marine Navigation Explore the Lowrance Eagle Series fishfinders and chartplotters with this comprehensive operator manual. Learn about basic operation, charts, sonar, navigation, and system settings for your Eagle 5, Eagle 7, and Eagle 9 units.
	Lowrance Eagle Eye Operator Manual - Your Guide to Advanced Sonar Explore the features and operation of the Lowrance Eagle Eye™ fishfinder and chartplotter. This operator manual provides detailed instructions on setup, navigation, sonar functions, and customization for anglers.
	Lowrance Eagle 4x Operator Manual This manual provides instructions for operating the Lowrance Eagle 4x fishfinder and sonar unit, covering basic operation, sonar and flasher image customization, and maintenance.