Conair ExtremeSteam Fabric Steamer with Dual Heat

Product Overview

The Conair ExtremeSteam Fabric Steamer with Dual Heat is designed for efficient wrinkle removal from garments and fabrics. This manual provides essential information for safe operation, assembly, maintenance, and troubleshooting.

Attachments

The steamer includes two attachments that easily snap over the soleplate. Ensure the steamer is off and cooled before adding or removing them.

• Bristle Brush Attachment: Useful for deeper fabric penetration.
• Soft Cushion Brush Attachment: Recommended for delicate fabrics.

Important Safety Instructions

DANGER:

• Always unplug the appliance immediately after use.
• Do not place or store the appliance where it can fall into a tub or sink.
• Do not immerse the appliance in water or other liquids.
• If the appliance falls into water, unplug it immediately. Do not reach into the water.

WARNING:

• Never leave the appliance unattended when plugged in.
• This appliance should not be used by, on, or near children or individuals with certain disabilities without supervision.
• Use this appliance only for its intended use as described in this manual. Do not use unrecommended attachments.
• Do not operate if the cord or plug is damaged, or if the appliance is not working properly, has been dropped, or immersed in water. Return to an authorized service center for examination and repair.
• Keep the cord away from heated surfaces. Do not pull or twist the cord. Allow the appliance to cool completely before storing.
• This appliance has a polarized plug (one blade wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If it does not fit, reverse the plug. If it still does not fit, contact a licensed electrician. Do not modify the plug.
• Never drop or insert any object into any opening or hose.
• Do not use outdoors or where aerosol products or oxygen are being administered.
• Do not use an extension cord.
• Surfaces may be hot when in use. Do not let heated surfaces touch eyes or skin.
• Do not place the steam nozzle directly on any surface or on the power cord while hot or plugged in. Use the stand provided.
• Unplug before filling or emptying the water tank and when not in use. Do not overfill.
• While emitting steam, this appliance may cause burns if used too close to skin, scalp, or eyes, or if used incorrectly. Test appliance away from the body before each use.
• Do not operate without properly filling the water tank with distilled water.
• Always keep the hose and nozzle elevated above the water tank.
• Never yank the cord to disconnect from the outlet. Grasp the plug and pull.
• Burns can occur from touching hot metal parts, hot water, or steam. Use care when removing water tank or turning the appliance upside down.
• To reduce likelihood of circuit overload, do not operate another high-wattage appliance on the same circuit.
• If an extension cord is absolutely necessary, a 15-ampere rated cord should be used. Arrange the cord to prevent pulling or tripping.
• Always remove the water tank from the appliance before filling with distilled water.
• When changing attachments, ensure the unit is off and no steam is being released. Ensure attachments are dry or cooled off.
• Never steam clothes that are being worn.
• Do not hold hand in front of steam.
• Test unit on an inconspicuous area of the item to be steamed to ensure fabric can tolerate steam effects.
• When steaming, keep the unit in motion and about one inch from the surface. Do not continuously hold steamer over an area or touch steamer jets directly to fabric as this can cause damage (shrinkage, melting, color shift).
• For heavier, durable fabrics (wool coats, bedding), slower passes may be necessary. Always test on an inconspicuous area first.

SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY

Steamer Assembly

Place the box on a large, sturdy, flat surface. Carefully remove the appliance from the packing material. Keep all plastic bags away from children. Some assembly is required.

Attaching the Telescopic Pole and Rotating Hanger

1. Remove the thumb screw from the bottom of the telescopic pole.
2. Insert the telescopic pole into the opening on the back of the steamer. Press down firmly to ensure the pole has reached the bottom. Replace the screw securing the pole to the base.
3. Fully extend the telescopic pole, locking the two clips.
4. Place the hanger assembly atop the pole, and hang the steam nozzle from the cradle.
5. Hang your garment for steaming away wrinkles. The hanger rotates 360 degrees.
6. Fill the water tank from the top opening with distilled water. Do not open the bottom cap (used for cleaning/removing excess water only).
7. Plug the steamer unit into a standard 120V AC power outlet.
8. The bristle brush and soft cushion brush attachments easily snap over the soleplate. The soft cushion brush attachment is recommended for delicate fabrics.

Get to Know Your Steamer

The Conair ExtremeSteam Fabric Steamer features:

• Steam nozzle with metal soleplate
• Multidirectional steam setting
• 4-position 360° rotatable hanger
• Clips for steaming pants
• Dial for steam setting
• Fabric creaser
• 56-inch flexible hose
• 3-section telescopic aluminum pole
• Removable water tank
• Lower pants clips
• Storage compartment for hose and attachments
• 4-wheel design for easy mobility
• Foot activated ON/OFF switch with ready light indicator

Operating Instructions

Filling the Water Tank (Prior to Plugging in the Appliance)

Remove the water tank using the handle on top. Fill the reservoir through the top opening with distilled water until the desired level. Do not overfill. Position the water tank on the base and ensure it is seated properly. Do not fill the tank with hot water. Do not unscrew the bottom cap unless for cleaning. Always empty or fill the tank over a sink, being careful not to spill water from the small top opening.

Turning Steamer On

1. Remove the water tank from the base, fill with distilled water, and press the tank down into the main unit.
2. Press the foot activated power switch once to turn the unit ON.
3. While water is heating, the green light will blink.
4. Once the green light is steady, the unit is ready to use.
5. Press the trigger switch on the steam head to release steam.
6. For continuous high-velocity steam, use the trigger lock.
7. The rotary switch on the steam head allows selection of the desired steam mode. The first setting emits steam through the soleplate, while the second setting emits steam from the top and sides. Adjust the amount of steam from the sides by turning the dial.
8. When water level is low, an audio warning will sound. Refill the water tank to continue.
9. Press the foot activated power switch again to turn the unit OFF.

How to Steam

Grasp the handle of the steam nozzle with the soleplate facing away. Begin at the bottom of the fabric to allow steam to rise inside and outside, removing wrinkles. Slowly move the nozzle from bottom to top. Some fabrics are best steamed on the underside. This relaxes fibers, eliminating wrinkles. Try the multidirectional steam setting for use inside garments to freshen and eliminate odors. Use the soleplate to help remove wrinkles in thicker, heavier, and less delicate fabrics, on an ironing board or similar surface.

NOTE:

• Test fabric for colorfastness in an inconspicuous spot.
• Drape linens, towels, handkerchiefs, and napkins over a rod or place on a towel rack.
• Heavier fabrics may require repeated steaming.
• With practice, users will gain speed and efficiency, learning which fabrics require multiple steam applications.

CAUTION:

• Do not directly touch velvet, silk, or other delicate fabrics with the steam head. Use extra caution when steaming delicate fabrics.
• Always steam with the hose in an upright position so condensation flows back into the reservoir. If steaming in a low position, condensation will collect in the hose. Lift the steam handle upward until the hose is fully extended to avoid this.
• Soleplate will be hot when in use. Avoid prolonged contact. Keep the steam head moving while steaming.

To Steam Drapes

Wash and dry drapes as directed. Rehang drapes and steam them when they are in place.

Using Pants Clip System

This fabric steamer is equipped with a pants clip system for holding pants taut for faster and more effective steaming. The two top pants clips are attached to the hanger to secure the top of the garment. The bottom clips can be adjusted by pulling them up to reach the bottom of the pants. If pants are too long for the bottom clips, use only the top clips and let the pants hang freely.

Using the Built-In Creaser

This fabric steamer has a built-in creaser. After assembly and turning on, follow these steps for sharp creases:

1. Move the selector switch to the 3-directional steam setting on the nozzle.
2. Hold the sleeve or pants leg by the cuff and slide the nozzle over the fabric. Position the fabric fully inside the creaser opening on the nozzle head.
3. Turn the nozzle 90 degrees so the fabric is taut and the crease is positioned properly. Caution: steam will exit from both sides of the nozzle.
4. While maintaining tension, run the nozzle up and down the garment, allowing steam and tension to create the desired crease.

Cleaning and Storing

1. Turn the ON/OFF switch to OFF and unplug.
2. Wait for the steamer to cool completely (at least 30 minutes).
3. Remove the water tank, open the bottom cover, and empty unused contents. Allow to air dry.
4. Collapse the telescopic hanger pole.
5. Replace the water tank.
6. Store the unit.

Decalcification

If the appliance produces steam more slowly or intermittently, decalcification may be needed to remove calcium deposits. For best performance, decalcify once a month, depending on usage frequency.

To decalcify:

1. Add a solution of 1/3 white vinegar and 2/3 distilled water to the water tank.
2. Place the water tank in the unit.
3. Plug the unit into an electrical outlet.
4. Turn to the ON position and run until half the amount has steamed (1 liter).
5. Turn the unit to OFF, unplug, and allow to sit for 30 minutes.

Repeat the procedure as many times as necessary (usually 2-3 times) until a normal steam rate returns, using a fresh solution each time. After decalcification, run one cycle of fresh, distilled water without vinegar through the unit before steaming garments again.

NOTE:

Amounts of chemicals in water vary by area. To ensure continued operation, use only distilled water. Never store the steamer without cleaning and removing excess water from the reservoir and water tank.

Troubleshooting the Steamer

• PROBLEM: Steamer fails to heat.
  CAUSE: Steamer not plugged in.
  SOLUTION: Plug into electrical outlet.
• PROBLEM: No steam.
  CAUSE: Water level is low (beep will sound).
  SOLUTION: Turn ON/OFF switch off and refill water tank.
• PROBLEM: Water drips from nozzle.
  CAUSE: Condensation in hose.
  SOLUTION: Hold the hose vertically and allow water to drain back into unit.
• PROBLEM: Poor steam performance.
  CAUSE: Sediment in tank.
  SOLUTION: Decalcify reservoir and water tank. Refer to decalcification instructions.
• PROBLEM: Dye on steam nozzle.
  CAUSE: Fabric not colorfast / Touching steam nozzle to fabric.
  SOLUTION: Move steam nozzle 1/2 inch away from fabric during use. Clean steam nozzle with household cleaner and rinse with water.
• PROBLEM: Discoloring of fabric.
  CAUSE: Dye on surface of fabric needs special treatment and cleaning / Fabric not suitable for steaming.
  SOLUTION: Some custom specialty fabrics have dyes that are NOT COLORFAST and are not suitable for steaming. Test fabric for colorfastness in an inconspicuous spot before steaming.

Limited One-Year Warranty

Conair will repair or replace (at its option) the unit free of charge for 12 months from the date of purchase if defective in workmanship or materials.

To obtain service under this warranty, return the defective product to the service center listed, together with the purchase receipt and $5.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 12 months from the date of manufacture.

ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply.

This warranty gives specific legal rights, and users may also have other rights, which vary from state to state.

Please register this product at: www.conair.com/registration

Service Center:
Conair Corporation
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307

For information on any Conair product, call: 1-800-3-CONAIR or visit: www.conair.com

©2015 Conair Corporation
East Windsor, NJ 08520/Glendale, AZ 85307
15PA012608 IB-13038A