Safety Instructions
This product is intended for domestic use only. Read this manual carefully before use and keep it for future reference.
- This product may be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, if supervised or instructed on safe use and understanding the hazards involved. Children should not play with the appliance. Cleaning and maintenance shall not be performed by children without supervision.
- This appliance contains a battery that can only be replaced by qualified persons.
- Use the appliance only with the supplied power adapter.
- The vacuum cleaner is intended for indoor use only. Do not use or install it outdoors, or in industrial or commercial environments.
- The appliance may cause a hazard if it runs over the power cord.
- Unplug the appliance from the power socket before cleaning or maintenance.
- To reduce the risk of fire, explosion, or injury, ensure the power adapter is not damaged before use. If the power adapter is damaged, do not use the vacuum cleaner.
- If the charger or battery is damaged, replace it with original parts purchased from the manufacturer or after-sales service.
- Turn off the vacuum cleaner before cleaning or replacing the roller brush.
- The electric brush head, extension tube, and vacuum cleaner conduct electricity, so do not immerse them in water or other liquids. After cleaning, ensure the filter, pre-filter, and post-filter are completely dry.
- To avoid personal injury, turn off the vacuum cleaner and remove the electric brush head before cleaning and maintenance. Do not use the vacuum cleaner before installing the electric brush head, dustbin cover, filter, pre-filter, and post-filter.
- Periodically check the extension tube and do not use it if it is damaged.
- Do not use the vacuum cleaner to collect flammable or explosive liquids, such as gasoline, or other liquids, e.g., water, or toxic liquids, e.g., bleach, ammonia, and drain cleaners.
- Do not use the vacuum cleaner to clean toner used in laser printers and copiers, as toner may cause fire or explosion.
- Do not use the vacuum cleaner to collect drywall debris, ash (e.g., fireplace ash), or smoldering or burning materials such as coal, cigarette butts, or matches.
- Do not use the vacuum cleaner to collect sharp or hard objects, such as glass, nails, screws, or coins. They may damage the product.
- Do not use the vacuum cleaner to clean stains of oily substances, strong adhesives, or dyes, such as shoe polish, paints, and pigments.
- Keep hair, loose clothing, fingers, and other body parts away from the vacuum cleaner's openings and moving parts.
- Do not point the suction port, extension tube, or other accessories towards eyes or ears, or put them into your mouth.
- Do not insert any objects into the vacuum cleaner's openings or use the vacuum cleaner with a blocked opening. Clean the vacuum cleaner of dust, fibers, hair, and other items that may restrict its suction power.
- Do not place the vacuum cleaner on unstable objects such as chairs or tables to prevent damage or personal injury from falling.
- Do not charge or store the vacuum cleaner near heat sources or in damp locations, such as next to a radiator, in the kitchen, or bathroom.
- Do not expose the appliance or battery to excessive temperature.
- Be aware of the risk posed by the terminals of a battery-powered appliance or the risk of battery short-circuiting caused by metal objects.
- Use only replacement parts approved by Xiaomi.
- In case of battery leakage, avoid contact with the liquid and take the battery to an authorized recycling facility. If contact with eyes occurs, rinse with plenty of water and seek immediate medical advice.
- Exercise extreme caution when using the vacuum cleaner to clean stairs.
- Fire hazard warning: Do not use perfumed liquids for the vacuum cleaner's pre-filter and post-filter. These products contain flammable chemicals that can cause the vacuum cleaner to ignite.
- Strictly follow the recommendations in this user manual and charge the vacuum cleaner at an ambient temperature of 0°C to 35°C. Improper charging may damage the battery.
- When using the vacuum cleaner, strictly follow the instructions in this user manual. Users are responsible for any loss or damage resulting from improper use of the vacuum cleaner.
- WARNING: Use only the power adapter supplied with this device.
- WARNING: Use only the detachable power adapter supplied with the device to charge the battery.
- Use only with power adapter BLJ15WJ270050P-V or AD-D0752700050EU01.
Regulatory Compliance Information
EU Declaration of Conformity
CE [CE Mark]
Beijing Shunzao Technology Co., Ltd. hereby declares that this product complies with the requirements of the relevant EU directives and European standards, as amended. The full text of the EU Declaration of Conformity is available at the following website: http://www.mi.com/global/service/support/declaration.html
WEEE Disposal and Recycling Information
All products marked with this symbol are considered Waste Electrical and Electronic Equipment (WEEE according to Directive 2012/19/UE) and cannot be disposed of with other waste after their end of life. To protect human health and the environment, please hand over your used equipment to a designated collection point designated by government or local authorities. Proper disposal of the used product helps prevent potential negative impacts on the environment and human health. For more information, please contact your local authority or installer.
Product Overview
Vacuum Cleaner Components
The vacuum cleaner unit includes:
- Dust Removal Button: Press to release dust from the dustbin.
- Dustbin: Collects dust and debris.
- Mode Button: Press to switch between Turbo and Standard modes.
- Battery Level Indicator: Shows the remaining battery charge.
- Charging Port: Connect the charger here.
- Power Button: Press to turn the vacuum on or off.
Accessories
The package includes various accessories:
- Extension Tube: Connects the main unit to the brush heads for extended reach.
- 2-in-1 Brush Nozzle: A versatile nozzle for crevices and surfaces.
- Electric Brush Head: For efficient cleaning of floors.
- Power Adapter: For charging the vacuum cleaner.
- Wall Mount: For convenient storage of the vacuum cleaner and accessories (includes 2 screws and 2 wall plugs).
Note: Illustrations of the product, accessories, and user interface are for reference only. Actual products and features may vary due to product improvements.
Installation
Attaching Accessories to the Vacuum Cleaner
- Connecting the Extension Tube and Electric Brush Head: Align the extension tube with the vacuum cleaner body and the electric brush head, then push them together until they click into place.
- Connecting the 2-in-1 Brush Nozzle: Align the nozzle with the vacuum cleaner body and push until it clicks into place.
Mounting the Wall Mount for Storage
- Choose a cool, dry location near an electrical outlet. Before mounting, ensure no pipes or wires are routed directly behind the mounting spot on the wall.
- The distance between the bottom of the wall mount and the floor should be 96.5 cm.
- Hold the wall mount in the desired position and mark the screw holes on the wall, aligning them with the holes on the mount.
- Use an electric drill with an 8 mm drill bit to drill a hole approximately 40 mm deep at each marked point, then insert a wall plug into each hole.
- Align the mounting holes on the wall mount with the holes on the wall, then use the provided screws to attach the mount to the wall.
Dimensions for Wall Mount Installation: The bottom of the wall mount should be 96.5 cm from the floor.
Charging
Battery Level Indicator Description
The battery level indicator shows the charging status:
Status | Indicator Light |
---|---|
Operating | Low Battery: Blinking |
Charging | Low Battery: Blinking |
Operating | Half Charged: On |
Charging | Half Charged: On |
Operating | Nearly Charged: On |
Charging | Nearly Charged: On |
Operating | Fully Charged: Off (after 20 seconds) |
Charging | Fully Charged: On (then turns off) |
Charging Notes
- Fully charge the vacuum cleaner before the first use. This will take approximately 5 hours.
- The vacuum cleaner cannot be used while charging.
- After the vacuum cleaner is fully charged, the indicator will turn off after 20 seconds, and the vacuum cleaner will enter power-saving mode.
- Vacuuming for extended periods at the highest suction level may cause the battery to heat up, which could extend charging time. It is best to let the vacuum cleaner cool down for 30 minutes before charging.
Usage
Electric Brush Head
Suitable for cleaning marble, wood, and short-pile carpet floors.
2-in-1 Brush Nozzle
Suitable for cleaning crevices and surfaces such as keyboards, curtains, sofas, ceilings, corners, and car interiors.
Note: To avoid potential safety hazards, do not expose the vacuum cleaner to direct sunlight or store it in high-temperature environments, such as inside a car in summer.
Care and Maintenance
General Warnings
- Before maintenance or care, disconnect the power and ensure the vacuum cleaner is turned off.
- Always use original parts to ensure normal operation and maintain warranty validity.
- If the filter, pre-filter, post-filter, extension tube, or 2-in-1 brush nozzle becomes clogged, the vacuum cleaner will stop working. Turn off the vacuum cleaner and clear the blockage before reuse.
- If the brush head gets blocked, it will stop working, but the vacuum cleaner will continue to operate. Turn off the vacuum cleaner and clean the brush head before reuse.
- Before cleaning, remove the brush head from the vacuum cleaner to prevent accidental activation, which could cause injury.
- If the vacuum cleaner will not be used for a long time, charge it fully, disconnect it from the power supply, and store it in a cool, low-humidity place away from direct sunlight.
- To prevent excessive battery discharge, charge the vacuum cleaner at least once every three months.
Cleaning the Dustbin
Before cleaning the dustbin, disconnect the power and remove the extension tube. The vacuum cleaner's performance will decrease when the dustbin is filled to the "MAX" mark. To restore its performance, empty the dustbin.
- Emptying the Dustbin: Hold the dustbin over a trash can and press the dust removal button to empty its contents.
Cleaning the Vacuum Cleaner Body
Wipe the vacuum cleaner with a clean, dry cloth.
Cleaning the Filter Assembly
- Press the dust removal button to open the dustbin, rotate the filter as shown to remove it, and then remove the pre-filter from it.
- Rotate the post-filter as shown to remove it.
- Rinse the filter, pre-filter, and post-filter under running water until clean, then place all filters aside to dry completely for at least 24 hours.
Notes:
- Never immerse the filter, pre-filter, or post-filter.
- When cleaning the post-filter, rinse it multiple times and tap its edge lightly to remove dust and debris until it is clean.
- Do not clean the pre-filter and post-filter with your hands, a brush, or sharp objects, as they could be damaged.
- If the suction power is still significantly reduced after cleaning the pre-filter and post-filter, you can try purchasing and replacing them with original ones.
Cleaning the Electric Brush Head
- Turn the brush head upside down and press the brush roller release button to unlock and remove the brush roller.
- Use a dry cloth or paper towel to wipe dust and debris from the suction port and the transparent cover. [Note: Do not clean the electric brush head with water as it has a built-in motor.]
- Reinstall the brush roller and press the lock to secure it in place.
Troubleshooting
If the vacuum cleaner is not working correctly, an error message will appear on the battery indicator. Compare it with the table below to resolve the problem.
Common Problems
Typical Problem | Probable Cause | Solution |
---|---|---|
Vacuum Cleaner Not Working | Battery is depleted. | Charge the vacuum cleaner before use. |
Suction port, air duct, pre-filter, or post-filter is blocked. | Check and clean immediately. | |
Filter, pre-filter, or post-filter is not installed correctly. | Check and install in place. | |
Battery thermal protection has been activated. | Wait for the battery temperature to return to normal, then resume operation. | |
Suction Power Decreased | Dustbin is full or pre-filter/post-filter is clogged. | Check and clean immediately. |
Brush head is clogged. | Clean the brush head. | |
Battery is not fully charged. | Charge the vacuum cleaner before use. | |
Brush Roller Not Spinning | Dustbin is full or pre-filter/post-filter is clogged. | Check and clean immediately. |
Brush head is clogged. | Clean the brush head. | |
Foreign objects are tangled in the brush roller. | Remove any foreign objects, then resume use. | |
Vacuum Cleaner Overheating / Brush Roller Not Spinning | Brush roller thermal protection has been activated. | Wait for the brush head motor temperature to return to normal before use. |
Conductive contacts are dirty. | Wipe the contacts with a soft, dry cloth and try again. | |
Cannot Charge | The power adapter used is not original. | Use only the original power adapter to charge the vacuum cleaner. |
Battery thermal protection has been activated. | Wait for the battery temperature to return to normal, then resume operation. | |
Battery Charging Slowly | Battery thermal protection has been activated. | Wait for the battery temperature to return to normal, then resume operation. |
Error Codes (LED Indicators)
Error Message (LED Pattern) | Probable Cause | Solution |
---|---|---|
LEDs 1, 2, and 3 blink simultaneously three times | Power error | Use only the original power adapter for charging. |
Battery thermal protection activated | Wait for the brush head motor temperature to return to normal before use. | |
Battery cell error | Contact after-sales service. | |
Temperature sensor error | Contact after-sales service. | |
LED 1 blinks ten times | Motor error | Battery is discharged. Use only the original power adapter for charging. |
Note: If the above suggestions do not resolve the problem, please contact the after-sales service department.
Technical Specifications
Xiaomi G20 Lite Vacuum Cleaner
Specification | Details |
---|---|
Name | Cordless Vacuum Cleaner |
Model | C203 |
Rated Voltage | 22.2 V |
Charging Voltage | 27.0 V |
Rated Power | 215 W |
Net Weight | 2.4 kg |
Power Consumption (Standby Mode) | ≤ 0.5 W |
Time to Standby Mode | < 20 min |
Electric Brush Head
Specification | Details |
---|---|
Model | C203-DS |
Rated Voltage | 22.2 V |
Rated Power | 15 W |
Power Adapter
Adapter 1
Specification | Details |
---|---|
Manufacturer | Zhongshan Baolijin Electronic Co., Ltd. |
Model | BLJ15WJ270050P-V |
Rated Input | 100-240 V ~ 50/60 Hz 0.5 A |
Rated Output | 27.0 V 0.5 A 13.5 W |
Average Efficiency During Operation | 85.9% |
Efficiency at Low Load (10%) | 73.2% |
No-load Power Consumption | 0.09 W |
Adapter 2
Specification | Details |
---|---|
Manufacturer | Shenzhen AMC Technology Co., Ltd. |
Model | AD-D0752700050EU01 |
Rated Input | 100-240 V ~ 50/60 Hz 0.8 A |
Rated Output | 27.0 V 0.5 A 13.5 W |
Average Efficiency During Operation | 84.5% |
Efficiency at Low Load (10%) | 75.5% |
No-load Power Consumption | 0.09 W |
Note: Models BLJ15WJ270050P-V and AD-D0752700050EU01 can be used with the vacuum cleaner, and only one of them is supplied in the package.
Environmental Protection Information
The lithium-ion battery pack of this vacuum cleaner contains chemicals that may pollute the environment. Before disposing of the vacuum cleaner, remove the battery and take it to an appropriate waste processing facility.
- Remove the battery from the device before disposing of it.
- The device must be disconnected from the power supply when removing the battery.
- The battery should be disposed of in an environmentally safe manner.
Warnings:
- Before removing the battery, ensure the vacuum cleaner is disconnected from the power supply and the battery is completely discharged.
- Dispose of removed batteries at a professional recycling facility for proper disposal.
- Do not leave the battery in a high-temperature environment where it could explode.
- In case of battery leakage, avoid contact with the liquid. If liquid comes into contact with eyes, rinse eyes with plenty of water and seek immediate medical advice.
Battery Removal:
- Remove the rear covers of the vacuum cleaner and handle, then remove the micro-switch from the handle.
- Using a screwdriver, unscrew the screws in the vacuum cleaner, then disconnect the wires and remove the battery pack.
- Unscrew the two screws above the battery pack's circuit board.
- Remove the top and bottom covers of the circuit board and battery pack, then remove the batteries.
Warranty
This warranty grants the user specific rights, but they may also have other rights provided by the law of their country, administrative region, or state. Furthermore, in some countries, administrative regions, or states, consumer law may provide for a minimum warranty period. Any exclusions, limitations, or suspensions of rights available to the user, invoked by Xiaomi, are only to the extent permitted by applicable law. To fully understand your rights, please refer to the law of your country, administrative region, or state.
1. Limited Product Warranty
Xiaomi warrants that Products will be free from material and workmanship defects under normal use and in accordance with the Product's user manual, for the Warranty Period. The warranty period and conditions are specified in the relevant local regulations. For more information on consumer warranty benefits, please visit Xiaomi's official website: https://www.mi.com/global/support/warranty.
Xiaomi warrants to the original purchaser that the Product will be free from material and manufacturing defects under normal use for the period mentioned above. Xiaomi does not warrant that the Product's operation will be uninterrupted or error-free. Xiaomi is not responsible for damages caused by failure to comply with the Product's usage instructions.
2. Forms of Remedy
If a product defect is found and Xiaomi receives a valid claim within the Warranty Period, Xiaomi will (1) repair the product free of charge, (2) replace the product, or (3) refund the cost of the Product, excluding any shipping fees.
3. How to Obtain Warranty Service
To obtain warranty service, you must deliver the Product in its original packaging or packaging providing an equivalent level of protection to the address specified by Xiaomi. Before claiming warranty service, Xiaomi may (to the extent permitted by applicable law) require you to provide proof of purchase and/or complete the product registration.
4. Exclusions and Limitations
Unless otherwise stipulated by Xiaomi, this Limited Warranty applies only to the Product manufactured by or for Xiaomi and identifiable by the "Xiaomi" or "Mi" trademark, trade name, or logo. The Limited Warranty does not apply to: (a) Damage caused by acts of nature or force majeure, such as lightning strikes, tornadoes, floods, fires, earthquakes, or other external causes; (b) Negligence; (c) Commercial use; (d) Modifications to any part of the Product; (e) Damage associated with the use of the Product in conjunction with non-Xiaomi products; (f) Damage resulting from accident, misuse, or abuse; (g) Damage caused by operating the Product outside the parameters or intended use described by Xiaomi, or due to incorrect voltage or power supply; (h) Damage caused by any service (including upgrades and expansions) performed by anyone who is not a representative of Xiaomi.
It is the user's responsibility to back up any data, software, or other materials stored or saved on the product. It is possible that data, software, or other materials in the device will be lost or reformatted during servicing, and Xiaomi is not responsible for any such damage or loss.
No Xiaomi reseller, agent, or employee is authorized to make any modification, extension, or addition to this Limited Warranty. If any term is held to be illegal or unenforceable, the legality and enforceability of the remaining terms shall not be affected.
After-sales services are limited to the country or region of original purchase, unless otherwise stipulated by applicable law or Xiaomi makes other commitments in this regard. Products that are not imported and/or not manufactured by Xiaomi and/or not purchased from Xiaomi or an official Xiaomi reseller are not covered by these warranties. In accordance with applicable law, you may have warranty rights provided by the unofficial seller who sold the product to you. Therefore, Xiaomi encourages you to contact the seller from whom you purchased the product.
These warranties do not apply in Hong Kong and Taiwan.
5. Implied Warranties
Except to the extent prohibited by applicable law, all implied warranties (including warranties of merchantability and fitness for a particular purpose) are limited to the maximum duration of this limited warranty. Some jurisdictions do not allow limitations on the duration of an implied warranty, so the above limitation may not apply to you in such cases.
6. Limitation of Liability for Damages
To the extent permitted by applicable law, Xiaomi shall not be liable for any incidental, indirect, special, or consequential damages whatsoever, including but not limited to loss of profits, revenue, or data, damages arising from any breach of express or implied warranty or condition, or any other legal theory, even if Xiaomi has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of liability for special, indirect, or consequential damages, so the above limitation or exclusion may not apply to you.
7. Contacting Xiaomi
Customers are encouraged to visit https://www.mi.com/global/support/warranty. The after-sales service contact person may be any person in Xiaomi's authorized service network, an authorized Xiaomi distributor, or the final seller who sold the product to the user. If in doubt, please contact the appropriate person designated by Xiaomi.