30" INDUSTRIAL HIGH VELOCITY OSCILLATING PEDESTAL FAN
MODEL NO: HVSF30.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
[info] Refer to instructions
Indoor Use Only
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
- You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. You must also read and understand the following instructions concerning electrical safety.
- ✔️ Ensure that cables are always protected against short circuit and overload.
- ✔️ Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none are loose.
- ✔️ Ensure that the voltage marked on the appliance matches the power supply to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
- ❌ DO NOT use worn or damaged cables, plugs or connectors. Have any faulty item repaired or replaced immediately by a competent electrician.
- ✔️ It is recommended that this heater is wired directly to a fused isolator switch. If, however, a plug is fitted, the following applies:
- ✔️ Fit a new plug according to the following instructions (UK only).
- a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
- b) Connect the BROWN live wire to the live terminal 'L'.
- c) Connect the BLUE neutral wire to the neutral terminal 'N'.
- d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable restraint is tight.
Diagram illustrating UK plug wiring: GREEN/YELLOW wire connects to the earth terminal (E), BROWN wire to the live terminal (L), and BLUE wire to the neutral terminal (N). The cable restraint is also shown. The recommended fuse rating is 5 Amp.
1.2. GENERAL SAFETY
- ✔️ Disconnect the fan from the mains power when not in use and before servicing or performing any maintenance.
- ✔️ Use the fan in dry areas only. ❌ DO NOT use in wet or areas with high condensation such as showers, pools etc.
- WARNING! If a fan falls into water or other liquid, immediately switch off and disconnect from the mains power supply. ❌ DO NOT touch the fan until the mains power supply has been disconnected.
- ✔️ Always disconnect the fan from the power supply when moving it from one location to another and ensure fan is stood on a level surface.
- ✔️ The fan air flow is powerful. Before use ensure that there is nothing nearby that will be damaged or displaced by the stream of air.
- ✔️ Keep the fan clean and maintained in good condition. For motor service contact an authorised service agent.
- ✔️ Use recommended parts only. Unapproved parts may be dangerous, and will invalidate your warranty.
- ❌ DO NOT operate the fan where there are explosive or flammable gases, fumes or other hazardous substances.
- ❌ DO NOT stand the fan on the power cable.
- ❌ DO NOT insert any objects through the fan guard.
- ❌ DO NOT cover the fan when in use.
- ❌ DO NOT immerse the fan in water or any other liquid.
- ❌ DO NOT allow children to operate the fan.
- ❌ DO NOT stand the fan where it may be knocked over or off a surface, or where the lead may cause a person to trip.
- ❌ DO NOT use the fan outdoors.
- ❌ DO NOT modify speed control or attempt to fit any additional external speed control device to the fan.
- ✔️ When not in use place the fan in its original box, or otherwise cover, to protect from dust and store in a safe, dry, childproof location.
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. INTRODUCTION
High velocity pedestal fan suitable for movement of huge volumes of air. Carefully balanced and fully guarded blades provide quiet and safe operation. Two-speed power selection, spring-assisted, height-adjustable stand and switchable head oscillation allow precise control of airflow to exactly where it is needed. Fitted with 3-pin plug. Suitable for industrial, commercial, agricultural, automotive workshop and showroom applications.
3. SPECIFICATION
| Model No: | HVSF30.V2 |
| Current: | 0.52A |
| Fan Diameter: | 760mm(30") |
| Height: | 1610-2030mm |
| Max. fan airflow rate (F): | 288m³/min |
| Fan power input: | 123W |
| Service value (SV): | 2.3(m³/min)/W |
| Standby power consumption (Psb): | 0.0W |
| Fan sound power level (Lwa): | 70dB(A) |
| Max. air velocity (c): | 3.8m/s |
4. OPERATION
4.1. ASSEMBLY
- Remove all packaging material and check contents with the parts list.
- Bolt the outer tubular stand to the base using the fixings supplied.
- Slide the inner tubular stand into the outer tubular stand, fit and tighten the set knob to hold at desired height.
- Locate the motor housing onto the top of the inner tubular stand and fix in place using the nut, bolt and washers supplied.
- Place rear guard against the motor housing and fix in place using the 4 sets of nuts and washers.
- Slide the fan onto the shaft and tighten the fixing screw with a crosshead screwdriver.
- Hook the front guard into place at the top of the rear guard and then push the 7 clips around the edge of the guards into place so that they engage both the front and rear guards.
4.2. OPERATION
IMPORTANT: Ensure that all safety instructions from section 1 have been read and understood before using the fan.
- Set the fan on a level, dry surface.
- Plug the power cord into the mains supply.
- The fan features 3 speeds - selectable using the chain operated switch located at the back of the fan. This operates in a cycle: OFF - LOW - MED - HIGH - OFF. LOW or MED settings will suit most needs, HIGH is used for maximum air movement.
- Adjust the direction of air flow up or down by loosening the knob and then tilting the fan assembly to the required angle, then re-tighten the knob. To adjust the height setting, loosen the lower knob, set at desired height and then re-tighten knob. To oscillate the fan press downwards on the knob on the top of the motor housing. To stop oscillation, pull the knob upwards.
- When not in use, disconnect from power supply and store in a safe, dry, childproof location.
5. MAINTENANCE
IMPORTANT: Turn the control switch to OFF and disconnect fan from power supply before cleaning.
- ✔️ Use only a soft, damp cloth to clean the fan.
- ❌ DO NOT submerge the fan in water and NEVER allow water to drip into the motor housing.
- ❌ DO NOT use solvents or other chemicals to clean the fan.
To clean the fan blades, loosen the 7 clips around the guards and then lift off the front guard from the top hook. Wipe the blades and guards. Reassemble by hooking the front guard into place at the top of the rear guard and then push the 7 clips back into place so that they engage both the front and rear guards. Store the fan in its original box or otherwise cover the fan to protect it from dust.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Notes and Warranty
Note: It is Sealey's policy to continually improve products and as such they reserve the right to alter data, specifications and component parts without prior notice. Other versions of this product are available. For documentation for alternative versions, please email or call the technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
