Car MP5 Player

Content

• Tips and Warnings
• Safety Notice
• Disassembly and Installation Steps
• Rear Interface Description
• Power Harness Description
• Rear View Camera Wiring
• Icon Introduction
• Phone Link
• Steering Wheel Control
• Parameters
• USB DVR function optional

Tips and Warnings

In order to emphasize the important information of the user manual, special attention should be paid when seeing the label ⚠, which indicates some important warnings and reminders.

Safety Notice

Read all instructions before installation. It is recommended that the machine be installed by a car audio professional.

⚠ This machine is suitable for the vehicle 12V power supply system (the ground wire must be grounded), please do not install the machine in the 24V vehicle, otherwise it will damage the machine.

⚠ Do not repair the power fuse without professional guidance. Improper use of the fuse can cause damage to the machine and cause a fire.

☑ To avoid violating traffic rules, drivers cannot watch videos while driving and operating machines to avoid unnecessary accidents.

⚠ For the sake of safety and to ensure the normal use of the product, please invite professionals to install, disassemble or repair the machine to avoid machine damage and accidents.

⚠ Please do not placing this product in a humid environment and water in case causing fire due to electric shock or other unnecessary damage.

Note: To Prevent Burning The Machine, Do Not Turn On The Power Until The Power Cord Is Properly Connected!

Test

A quick simple test before the installation is to confirm that the device is working normally and as expected in case there is a wrong step in the subsequent installation, which will cause it to fail to work. If you perform a successful test but the unit did not work after installing it please recheck the installation steps.

Test car stereo:

1. The red and yellow wires of the car stereo combine together firstly and then connected to the positive pole of the 12V battery
2. The black wire is connected to the negative pole of the battery.
3. Two seconds later, check the car stereo. If the screen is lighting up, it means the car stereo is properly functioning.

Disassembly and Installation Steps

1 Screw fixed installation

2 Card position fixed installation

3 Special frame fixed installation

Rear Interface Description

(Note: The picture is for reference only, please refer to the actual product)

Hardware 1

• Power Cable
• USB Cable
• Radio Antenna
• S.W Output
• Video output
• Video input
• Camera Input

Hardware 2

• Video Output
• Audio Output 1
• Radio Antenna
• Audio Output 2
• S.W Output
• Video input
• Camera Input
• Power Cable
• USB DVR
• Video Input

Hardware 3

• Video Output
• Audio Output 1
• Radio Antenna
• Audio Output 2
• Canbus
• Camera Input
• Power Cable
• USB DVR
• Video Input
• S.W Output

Power Harness Description

(Note: The picture is for reference only, please refer to the actual product)

power harness 1

Components: Auto Antenna, Steering wheel, Rear Camera, Headlight detection line, ACC, Battery 12V

power harness 2

Components: Steering Wheel, Headlight detection line, Reversing Camera, ACC, Auto Antenna

Power Harness 3

Components: Rear View Camera, Steering Wheel, Ground Wire(B-), +12V(B+), Ground Wire(B-), Headlight Detection Line, ACC

Rear View Camera Wiring

When using the rear view reversing function, the system will automatically disconnect the link with the mobile phone, such as calls and music in Bluetooth mode, mobile phone mirroring links, etc., which are all normal.

Note: When Installing, Whether You Use a Reversing Camera Or Not, Please Connect The Reversing Cable. Otherwise, Your Wifi And Bluetooth Signals Will Be Affected !

1.Monitor (Not Included in the Package)

2.Camera Power Source

3.Camera (Optional)

Diagram Description: A car with wiring shown for the rear view camera. A separate diagram shows the connection details for the reversing trigger line, video out, camera power cable, and reversing light cable to the monitor.

Reversing trigger line: Connect this wire to the reversing line in the power harness, ie: Back (A6)

Red: Connect to the positive pole of the Reverse light Cable

Back to GND

Monitor: 1. NTSC FORMAT 2. PAL/NTSC Auto Switch Light

Icon Introduction

Machine - Host

Show UI

(Note: The picture is for reference only, please refer to the actual product)

Image Description: Multiple screenshots of the car MP5 player interface. One shows basic setup options like Name, Pin Code, and Vehicle settings. Another shows radio area selection. A third displays the radio tuning interface with frequency and band options. A fourth shows an equalizer with frequency bands and volume levels. The final image shows the Phone Link interface with options for iPhone (CarPlay, Mirror) and Android (Auto, Mirror).

Phone Link Options:

• 1. Wired/Wireless iOS CarPlay
• 2. Wired iOS mirror Link
• 3. Wired/Wireless Android Auto
• 4. Wired Android mirror Link

For Mirror Link, you can choose Android Wired/Wireless Connection or Apple Wired/Wireless Connection according to your requirements. You can click the corresponding module to see how to use the Mirror Link.

Steering Wheel Control

Image Description: A screenshot of the car player's settings menu, highlighting the 'Wheel' option. It shows buttons for 'Pre', 'Next', 'Power', 'Vol-', 'Vol+', 'Mute', 'Dial', 'Reject', 'Mode', 'Default', and 'Enter'.

Steering wheel control learning method:

Connect the KEY and KEY2 on the car player's power cable plug to the original car's steering wheel control wire. After touching the button icon on the screen, quickly find the corresponding function button on the steering wheel of the original car, then press the button until the machine screen prompts that the installation is successful, then release it! Indicates that the learning is successful, you can learn the next button.

Parameters

USB DVR function optional

Image Description: A screenshot of the USB DVR interface showing a road scene. Icons for 'Takepic', 'Record', 'Lock', 'Replay', and 'Setting' are visible. Below the image, each function is explained.

• Takepic: Take picture function: Press this icon to Save the pictures you like.
• Record: Record Function: Press this icon to Record and save the pictures you like.
• Lock: Lock: Press this icon to keep and lock you like.
• Replay: Replay Function: All the video and images are saved here.
• Setting: Setting Function: Into Setting interface, according your request to set what you want.

REC This icon is flashing when it is being videotaped.

🔊 This Icon is sound recording, Optional voice and no voice.

🔃 This Icon is recycling video of few minutes.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

Thank you again for using the product. If you have further questions, please contact the service staff. Product UI or functions may be modified and upgraded from time to time without notice. It is normal if the manual has some discrepancies.