CandAuto Car MP5 Player User Manual

Customer Service

CandAuto strives to deliver high-quality products and will continue to do so. It is recommended that the product is not installed by the user. Professional installation by a certified professional is advised. If you choose to install the unit yourself, please read the user manual carefully and follow the installation steps.

Tips and Warnings

Special attention should be paid to information highlighted with a warning symbol (⚠️), which indicates important warnings and reminders.

Safety Notice

Read all instructions before installation. It is recommended that the machine be installed by a car audio professional. This machine is suitable for a 12V power supply system (the ground wire must be grounded); do not install it in a 24V vehicle, as this will damage the machine. Do not repair the power fuse without professional guidance; improper use of the fuse can cause damage and fire. To avoid violating traffic rules, drivers must not watch videos while driving and operating the machine to prevent accidents. For safety and normal product use, please invite professionals to install, disassemble, or repair the machine to avoid damage and accidents. Do not place this product in a humid environment or near water, as this may cause fire due to electric shock or other damage.

Read the Entire Manual:

• Keep The Manual
• Clean with A Dry Cloth only
• Follow All instructions
• Do Not Use Or Operate Near Water
• Do Not Defeat Any Safety Features

Note: To Prevent Burning The Machine, Do Not Turn On The Power Until The Power Cord Is Properly Connected!

Installation Testing

Test Car Stereo

A quick test before installation confirms the device is working normally. If the unit does not work after installation, recheck the steps.

1. Combine the red and yellow wires of the car stereo and connect them to the positive pole of the battery.
2. Connect the black wire to the negative pole of the battery.
3. After 2 seconds, check if the screen lights up. If it does, the car stereo is functioning properly.

Diagram Description: A visual shows two connectors labeled A and B. Connector A has multiple pins. Connector B shows a block with wires: Red (+12V), Black (GND/Ground wire B-), and Yellow (+12V), each connected to corresponding terminals. The diagram also shows circular connectors for audio output.

Test Rear View Camera

This step requires the rear view camera to be purchased separately.

1. Connect the pink wire to the top red wire of the rear view camera.
2. Combine the middle red wire and the bottom red wire of the rear view camera and connect them to the positive pole of the battery (where the red and yellow wires were connected previously).
3. Connect the black wire of the rear view camera to the negative pole of the battery (where the black wire was connected previously).
4. If the camera lights up and the car stereo displays the reverse image, the rear view camera is functioning properly.

Diagram Description: A visual shows connector A and B, similar to the stereo test. It also shows a separate wiring harness for the camera with wires labeled Red, Black, Yellow, and Pink. The diagram illustrates how these wires connect to the main unit and the camera itself. The camera unit is also depicted.

After completing the tests, the car stereo is ready for installation.

Wiring Diagram Reference

Attention: The specific wiring is subject to the actual product.

Example 1

Diagram Description: A detailed wiring diagram shows connections for a car stereo unit. Connector A has wires labeled Red (ACC/Ignition Switch +12V), Black (GND/Ground wire B-), Blue (ANT/Auto Antenna Power), Brown (ILL/Headlight control line), Green (KEY1/Steering wheel controls), Yellow (B+/Power Supply +12V), Orange (Parking single check), and Pink (Parking Sensor Control Wires). Connector B shows connections for speakers: Green (Rear Left Speaker+), Green/Black (Rear Left Speaker-), White (Front Left Speaker+), White/Black (Front Left Speaker-), Gray (Front Right Speaker+), Gray/Black (Front Right Speaker-), Purple (Rear Right Speaker+), Purple/Black (Rear Right Speaker-). The diagram also illustrates connections for Left speaker, Right speaker, External display, External video source, Rear view camera, FM radio, USB DVR (optional), and Connect microphone.

Example 2

Diagram Description: Another wiring diagram illustrates connections, similar to Example 1 but with slightly different wire color assignments for some functions. It shows connections for ILL (Backlight), Steering Wheel Controls (1 & 2), Reversing Camera Wires, Brake Detect, ACC, Auto Antenna, Rear Left Speaker (+/-), Rear Right Speaker (+/-), Front Left Speaker (+/-), Front Right Speaker (+/-), Ground Wire (B-), and +12V Constant Power Supply (B+). It also shows connections for External display, Rear view camera, FM radio, Connect microphone, and USB DVR (optional).

Machine Installation

Common disassembly instructions are provided. Different models may vary; this image is for reference only.

The size of this car stereo is universal and suitable for most cars. Installation can be done by following the steps below. If the unit is not suitable for your car, consider aftermarket accessories such as a Double DIN dash kit, wire harness, and antenna adapter, which can be found by searching your vehicle's year, make, and model online. Alternatively, the original car frame may need modification.

Installation Methods:

1. Screw fixed installation: Diagram Description: Illustrates a car dashboard opening and the stereo unit being secured with screws.
2. Card position fixed installation: Diagram Description: Shows the stereo unit being inserted into a mounting bracket or car dash slot, secured by clips or slots.
3. Special frame fixed installation: Diagram Description: Depicts the use of a custom-fit frame to integrate the stereo into the dashboard.

Function Description

• HD Touch Screen
• BT/FM/USB Mp5
• USB 2.0 port
• Audio Playback Formats: MP3/WMA/WAV/FLAC/OGG/APE
• Video Playback Formats: RM/RMVB/DVD(VOB)/VC-D(DAT)/MP1/MP2/DIVX/XV1D/MP4/H263/H264/FLV/3GP/SWF/AVI/ASF/MJPEG etc.
• FM Range: 87.5 MHz - 108.00 MHz (Europe)
• With Remote Control
• Power-off with auto-memory store function under radio or USB mode
• Clock Function
• Mute Function
• BT Function
• Bass & Treble, L&R channel stabilizer
• Rear view camera function
• Video input Function
• USB interface charging
• Phone link (Optional)

Tip: Different models have different functions. Specific functions are subject to the actual product.

Common Icon Function Instruction

Video and Music Function Buttons

Due to different versions, icon functions may vary. This information is for reference only.

Icon Introduction (Machine - Host)

Function Description (For reference only)

Radio

Click the "FM/Radio icon" to enter radio mode. Band Selection: Press "FM" to turn to radio mode, then press "FM1" to select different bands (FM1/2/3). Browse/Auto Memory stations: Press "AS/PS" to browse saved stations (each lasts 10 seconds). When you find a desired station, press it to play. Hold "AS/PS" for 3 seconds to store stations automatically. The radio searches and stores stations from the present band, prioritizing strong signals first, then weak signals.

1. Manual search: Press ◀️ or ▶️ to manually change radio frequency.
2. Auto search: Hold ◀️ or ▶️ to automatically search for different radio frequencies.

USB/TF Play

Insert a USB flash drive/TF card to play videos and music. The USB interface also supports phone charging.

Audio/Video Input

Click the application icon to enter the interface for audio and video playback. Select files to play. Supported formats: AVI, MKV, QT, MPG, ASF, FLV, RMVB, MP3, WMA, ACC, WAVE, FLAC, APE, OGG, MP4 etc. Image formats: BMP/GIF/JPG/PNG.

Steering Wheel Learning

The steering wheel learning steps are as follows:

1. Press any button on the steering wheel. The interface will display a prompt; you will not be able to learn without pressing the steering wheel button for a while.
2. Click on the screen to learn the docking function.
3. Click the corresponding function button on the steering wheel and repeat steps 1-3 in sequence until all control buttons are completed.

Implementation conditions for this function:

• Original steering wheel for non-bus control.
• The steering wheel key must use the voltage input control method.

BT (Bluetooth)

1. Click the settings icon, then click the BT icon to enter the BT connection page.
2. Search for the BT name of the device. The phone will display a matching code. Click and confirm to match and connect.
3. PIN Number: "0000", "1234", or "88888888" (if required).
4. Pairing Devices: If the car is not paired, go to Phone > Settings > BT > Search for Device. Find the BT name "CAR***" and connect. The phone will prompt for a PIN code or confirm directly.
5. Call Function: Click on the number to input a phone number. Press ? to dial. Press ? to end the current call. Click ↩️ to delete input.
6. Telephone Directory: Enter the phone book interface. Click "Sync Contact" to synchronize contacts. Click the ? button to open a search box and enter English letters to search.
7. BT Music Playback Function: Connect to a BT phone for playback/pause/up/down operations. Go to the music page on your phone and click play.

Icons: ⏪ The previous song, ▶️/⏸️ Pause/Play, ⏩ Next song.

AUX

The AUX line is transmitted to the original car player (only some models support).

Mirrorlink (Optional)

Click the "Mirrorlink Icon" menu and enter "Phone link" to connect your phone to the MP5.

1. Phone display mode must be set to "landscape" for full-screen display on the car stereo.
2. BT must be connected to synchronize audio.
3. If the phone screen turns off, the car stereo display will also turn off.

For Android Mirror Link

When using an Android device, connect the USB data cable. You will be prompted to install APP software. After installation, plug the data cable again to enter screen mirroring mode. Operation is possible on both the player and phone screens. Image transfer requires a successful USB connection; sound requires a successful Bluetooth connection.

1. Wired mirror link (supported by some models): Use the data cable to connect the device with the Android mobile phone and confirm the authorization request on the mobile phone. Diagram Description: Shows a car stereo screen and an Android phone screen displaying "Touch input YES" and "Mirrorlink APP".
2. Wireless mirror link (supported by some models): Wirelessly search for this product device on your mobile phone and connect.

For iPhone Mirror Link

Note: Some high-configuration phones may not be suitable. Functionality varies by product model and connection method.

1. Wired mirror link (supported by some models): Use the data cable to connect the device with the Apple phone and confirm the authorization request on the phone. Diagram Description: Shows a car stereo screen and an iPhone screen displaying "Touch input NO" and "You can't control your iphone here."
2. Wireless mirror link (supported by some models): Wirelessly search for this product device on your mobile phone and connect. Diagram Description: Similar to wired, showing "Touch input NO" and "You can't control your iphone here."

Apple CarPlay (wired & wireless) (Optional)

Please refer to specific model support.

1. Wired connection: Connect the USB data cable to automatically enter the CarPlay interface.
2. Wireless connection: Turn on BT and Wi-Fi on the mobile phone, then connect BT. This will automatically enter the CarPlay interface. (Note: Signal is transmitted via Wi-Fi. If BT is off, transmission continues. If Wi-Fi is off, CarPlay disconnects.)

Diagram Description: Shows a smartphone interface with CarPlay icons (Phone, Music, Maps, Messages, etc.) and a car stereo screen displaying the CarPlay interface.

Android Auto (wired & wireless) (Optional)

Please refer to specific model support.

This feature is not supported in all countries. "Google Play" services must be available locally.

1. Download and install "Android Auto" software from "Google Play".
2. A mobile phone with Android 6.0 or higher is needed. Use a valid data cable connection.
3. Wired connection: Connect the USB data cable to automatically enter the Android Auto interface.
4. Wireless connection: Turn on BT and Wi-Fi on the mobile phone, then connect BT. This will automatically enter the Android Auto interface. (Note: Signal is transmitted via Wi-Fi. If BT is off, transmission continues. If Wi-Fi is off, Android Auto disconnects.)

Diagram Description: Shows a smartphone interface with Android Auto icons (Google Maps, YT Music, Spotify, Phone, etc.) and a car stereo screen displaying the Android Auto interface.

Reversing Camera Connection (CCD)

The reversing video input can be connected via an RCA adapter cable. When a signal is present, the LCD will automatically switch to the camera image (camera purchased separately).

1. Refer to Rearview Camera Installation before use.
2. If the rearview camera is not installed, "No Signal" will be displayed.
3. "Rearview Cam" can be triggered by: Pressing the "Rearview Cam" icon on the main interface or engaging the vehicle's reverse gear. In case of reverse gear engagement, it will automatically enter and display the rear view image.

[Safety Warning]: When driving normally, please try not to turn on the rearview camera to avoid distracting attention.

Rear View Camera Wiring

When using the rear view reversing function, the system will automatically disconnect from the mobile phone (calls, music, mirroring links, etc.). This is normal.

Note: When installing, whether using a reversing camera or not, please connect the reversing cable. Otherwise, Wi-Fi and BT signals may be affected!

Components: 1. Monitor, 2. Camera Power Source, 3. Camera (Optional).

Diagram Description: A car outline illustrates the placement of the monitor, camera power source, and camera. A detailed wiring diagram shows the "Reversing trigger line" connecting to "Back (A6)" in the power harness. The "Video Cable" connects to the "Reverse light Cable" (Red to positive, Black to GND). The "Camera Power Cable" connects to the "+ Reversing light Cable". The "Video (out)" from the monitor is also shown. The monitor itself is depicted with NTSC FORMAT and PAL/NTSC Auto Switch Light options.

After installation, start the engine and put the car in reverse. Check if the monitor displays the rear view image. If not, check the installation. The final step is to adjust the camera angle to ensure the rear bumper is clearly visible (suggested to occupy 5% of the screen image). Then, lock the lens bracket screws and complete the installation.

Attention: Adjusting the lens angle to see the bumper improves reversing safety. Please install strictly according to instructions.

Simple Troubleshooting Guide

Troubleshooting Details

1. Car radio does not turn on, or turns off after prolonged use: Ensure red cable connects to ignition-positive terminal, yellow to battery-positive (B+ 12V), and black to battery-negative (GND 12V). Use only in a 12V-output vehicle. If it remains off, temporarily connect red and yellow cables together to the 12V-positive terminal. If still no power, check the fuse.
2. Car radio powers on but produces no sound, or sound cuts out: Speaker negative wires may be improperly grounded. The amplifier IC might be burned out due to a short circuit. Check speaker cables for short circuits and ensure insulation. Test with a different speaker to confirm if the issue is with the radio or the car system.
3. Car radio's BT is not working, or disconnects: Forget the device "CAR-MP5" in phone's BT settings and re-pair. Use default PINs (0000, 1234, or 88888888). If issues persist, try the "reset hole" on the front panel or disconnect the power connector for a few minutes.
4. Car radio's mic is not working, or calls are unclear: Check BT volume settings. Ensure the dashboard is not too low, affecting mic pickup.
5. Car radio cannot read USB flash disk or SD/TF card: Confirm card capacity (supports lower than 32GB normally). Try other cards. Ensure the card is inserted correctly.
6. Car radio's remote control does not work: Check the remote's battery.
7. Reversing camera cannot work: Check if the pink cable is wired correctly with the reversing camera's controlling cable. Contact for advice if unsure.
8. Car radio cannot save time or station settings: Ensure the Yellow cable is wired to the car's 12V+ constant positive terminal.
9. Car radio noise problem: Especially with amplifiers, noise can be due to interference. Ensure cables are well-wrapped. Test with a different speaker to isolate the problem.
10. Screen Mirroring Failure: Check device compatibility. Enable car's Wi-Fi/BT and phone's screen mirroring. Select "CAR-MP5". If no signal, restart both devices. Note that some phones do not support mirroring.

If problems persist after troubleshooting, contact customer support for assistance.