Manuals+

Poulan Pro PP19A42 Tractor Illustrated Parts List

MFG. ID NO.: 96042018701

CUSTOMER CATALOG NO.: PP19A42

PRODUCT NO.: 960 42 01-87

Document Revision: 115 91 73-49 Rev. 2

Decals

KEY NO. PART NO. DESCRIPTION
1 587 84 40-01 Decal, Snowflake
2 585 71 38-01 Decal, Replacement
3 501 51 79-01 Decal, Engine HP
4 587 71 20-01 Decal, Deck Warr. Pop
5 584 90 46-01 Decal, Deflect. Warning
6 581 57 89-01 Decal, Fender Warning
7 582 67 72-01 Decal, Ins Str Wh
8 501 50 36-01 Decal, Side Panel
9 582 67 73-01 Decal, Fender
10 581 58 00-01 Decal, V-Belt Sch.
12 582 67 74-01 Decal, Hood RH/LH
15 532 14 50-05 Decal, Caution, Battery
-- 581 72 48-01 Decal, Bypass
-- 532 40 95-07 Pad Foot Pedal RH
-- 532 40 95-05 Pad Footrest LH
-- 115 91 72-49 Manual, Operator's (English/Spanish)
-- 115 91 73-49 Manual, Parts (English/Spanish)
-- 115 63 96-46 Quick Start Guide (English/Spanish)

Wheels & Tires

KEY NO. PART NO. DESCRIPTION
1 532 05 91-92 Cap, Tire Valve
2 532 06 51-39 Stem, Valve
3 532 10 62-22 Tire, Front 15 x 6-6
4 532 05 99-04 Tube, Front (Service item only)
5 532 12 51-21 Rim Assembly, 6" Front
6 532 12 49-57 Fitting, Grease (Front wheel only)
7 532 12 49-59 Bearing, Flange (Front wheel only)
8 532 12 51-22 Rim Assembly, 8" Rear
9 532 13 84-68 Tire, Rear 20 x 8-8
10 532 12 49-26 Tube, Rear (Service item only)
11 532 19 32-68 Cap, Hub Axle
-- 532 14 43-34 Sealant, Tire (10 oz. Tube)

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

Electrical System Schematic

Note: The tractor is equipped with a special alternator system. The lights are not connected to the battery but have their own electrical source. Because of this, the brightness of the lights will change with engine speed. At idle, the lights will dim. As the engine speed is increased, the lights will become their brightest.

Ignition Switch Positions:

Charging System Output: 3 AMP DC @ 3600 RPM

Lighting System Output: 5 AMP AC @ 3600 RPM

Power Outlet (Optional): 28 VOLTS AC MIN. @ 3600 RPM (Charging System Disconnected), 14 VOLTS AC MIN. @ 3600 RPM (Lights Off)

Note: If wiring insulated clips were removed for servicing of the unit, they should be re-installed to properly secure the wiring.

Electrical Components

KEY NO. PART NO. DESCRIPTION
1 532 16 34-65 Battery
2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4
8 532 19 32-28 Box Battery
16 532 17 61-38 Switch Interlock
21 532 40 02-52 Harness Asm Light w/4152j
22 532 00 41-52 Bulb Light #1156
25 581 49 80-01 Cable Starter
26 532 17 51-58 Fuse 20 AMP
27 873 51 04-00 Nut Keps Hex 1/4-20 unc
28 532 42 16-86 Cable Ground 6 Ga. 12" Black
29 532 19 27-49 Switch Seat
30 532 19 33-50 Switch Ign
33 532 41 19-33 Key/Chain
34 532 11 07-12 Switch Light/Reset
40 585 84 94-01 Harness Ign Dash
43 582 04 28-01 Solenoid
55 817 06 05-12 Screw 5/16-18 x 3/4
71 501 13 37-01 Harness Chassis
79 532 17 52-42 Socket Asm. Bulb Twistlock
87 532 19 78-02 Switch Interlock
90 532 43 53-95 Cover Terminal Battery
99 817 67 04-12 Screw Hexwsh Thdrol 1/4-20 x 3/4
102 581 02 34-01 Harness Pigtail
105 532 40 75-68 Switch Reverse
106 532 17 48-14 Palnut 1/4 Lugs

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

Chassis and Enclosures

KEY NO. PART NO. DESCRIPTION
5 501 42 83-01 Dash
14 532 40 95-98 Hood
15 581 05 58-01 Lens Left
18 581 05 57-02 Grille
25 581 05 59-01 Lens Right
34 580 91 08-01 Plate Engine
36 817 06 05-12 Screw 5/16-18 x 3/4
37 532 42 07-96 Fender
52 873 68 05-00 Nut Lock 5/16-18
58 532 41 22-80 Drawbar Upper
68 539 99 08-58 Screw Thdrol 5/16-18 x 1/2
130 532 41 63-58 Screw #10 x 0.750
138 532 40 97-30 Cupholder
150 532 40 83-10 Duct Heat Hood
151 532 18 75-68 Bracket Pivot
152 532 19 95-35 Shield Browning
159 817 00 06-12 Screw Hexwsh Thdrol 3/8-16 x 3/4
162 532 14 24-32 Screw Hex Wsh Hi-Lo 1/4 x 1/2
175 532 19 94-72 Crossmember
176 532 40 07-76 Screw 10-24 x 5/8 Wshd Qdrx
177 532 19 52-28 Bushing Steering
180 532 41 50-63 Chassis
181 532 40 47-96 Bushing Mtg. Fender Crgo.
182 532 40 71-76 Dash Lower
183 874 52 05-20 Bolt 5/16-18 x 1-1/4
189 817 00 05-12 Screw 5/16-18 x 3/4
191 581 05 60-02 Insert Reflector RH
194 873 90 05-00 Nut Lock Hex Flange 5/16-18
196 532 41 45-81 Console Asm. Deck Lift
213 874 76 05-12 Bolt 5/16-18 x 3/4
217 532 40 91-67 Rod Pivot Hood
218 532 19 63-95 X-Piece Hood Step
225 581 05 62-01 Trim Ring
228 532 1951-61 Stud Fastener
235 532 40 61-29 Spacer Fender
236 873 93 05-00 Nut Center Lock 5/16-18
237 532 40 37-04 Plug Mount Cargo
287 817 60 04-06 Screw 1/4-20 x 3/8
297 581 05 60-01 Insert Reflector LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

Drive System Components

KEY NO. PART NO. DESCRIPTION
1 Transaxle, Variator SD Pedal (590277501) (Order parts from transaxle manufacturer.)
2 532 12 35-83 Key Square
5 874 76 06-36 Bolt 3/8-16 x 2-1/4
6 532 12 40-28 Bushing Snap
15 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
17 501 48 71-01 Spring, Brake
29 584 82 31-01 Brake VATR
33 812 00 00-01 Ring E
35 532 40 10-31 Rod, Brake, Park
37 532 18 89-67 Washer .793 x 1.637 x 060
42 532 12 48-72 Cover, Foot Pedal
49 872 11 06-14 Bolt 3/8-16 unc
50 532 19 43-27 Idler Flat
51 873 90 06-00 Nut Lock
52 532 19 43-26 Idler V-Groove
56 532 19 72-53 V-Belt, Drive
64 589 67 14-01 Subasm. Shaft Pedal Brake
67 582 58 01-01 Washer Nylon 13/32 x 13/16 x .109
73 874 49 05-44 Bolt Hex 5/16-18 x 3.75
99 532 43 59-35 Rod Bypass
116 873 90 05-00 Nut Lock Hex Flange 5/16-18
125 817 00 05-12 Screw 5/16-18 x 3/4
143 539 99 08-58 Screw Thdrol 5/16-18 x 1/2 TYTT
159 876 02 04-12 Pin Cotter 1/8 x 3/4
160 532 16 94-84 Retainer Clip
161 532 10 57-09 Spring Return Clutch
163 587 84 79-01 Rod Control
166 532 42 91-64 Nut Push.625
167 532 40 52-57 Latch Brake Parking
172 583 97 42-01 Strap Torque
184 532 41 14-84 Handle Park Brk.
185 872 11 06-22 Bolt 3/8-16 unc x 2-3/4
186 532 19 43-21 Spacer Retainer
187 819 13 32-10 Washer 13/32 x 2 x 10 Ga.
188 582 21 70-01 Link Clutch Ground Drive Long
189 532 19 43-17 Bellcrank Ground Drive
190 532 19 43-18 Keeper. Bellcrank
195 581 50 46-01 Bracket Brake
203 819 11 11-16 Washer 11/32 x 11/16 x 16 Ga.
205 532 12 17-48 Washer 25/32 x 1-5/8 16 Ga.
210 588 92 10-01 Rocker Asm. Pedal
211 532 12 01-83 Bearing Nylon
214 532 42 12-63 Pedal Forward
215 532 44 82-54 Pad Pedal Reverse
221 532 40 31-87 Retainer Spring
222 879 21 20-10 Washer Flat
277 532 44 85-00 Subasm Link Rocker Pedal
282 874 49 05-48 Screw Thdrol 5/16-18 x 3
299 532 41 56-83 Bracket Mount
300 532 41 56-81 Keeper Idler
301 532 41 56-80 Pulley Idler Groove
302 581 42 05-01 Puller Idler Flat
303 872 11 06-18 Bolt
306 876 02 04-16 Cotter Pin
345 872 11 06-06 Bolt 3/8-16 unc
373 581 46 18-01 Spacer Idler
374 581 47 52-01 Arm Control Brake
375 873 68 06-00 Nut Crownlock 3/8-16 unc
380 582 47 86-01 Nut Flg Nylock 1/4-20 Gr G ZY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

Engine Components

KEY NO. PART NO. DESCRIPTION
1 532 44 67-60 Engine, B&S 33R877-0023-G1 (501450101) (Order parts from engine manufacturer.)
2 Muffler Exhaust B&S
9 582 54 03-02 Keeper Belt Engine
12 586 72 90-01 Pulley Engine
15 532 43 30-08 Tank Fuel Front
18 581 17 61-01 Cap Asm Fuel
20 587 24 26-01 Control Th/ch Flag
21 532 41 63-58 Screw #10 x 0.750
28 532 40 11-37 Line Fuel
29 532 13 71-80 Kit Spark Arrestor (Flat Scrn)
37 532 12 34-87 Clamp Hose
42 539 99 02-47 Washer SLW STD 7/16
45 873 51 04-00 Nut Keps Hex 1/4-20 unc
69 532 16 52-91 Gasket Eng 1 313 Id Tin Plated
79 532 19 23-34 Screw Socket Head 5/16-18 x 3/4
81 532 14 84-56 Tube Drain Oil Easy
82 532 42 82-87 Valve Oil Drain
84 817 06 06-20 Screw 3/8-16 x 1-1/4
85 501 60 65-01 Bolt Hex 7/16-20 x 4 x Gr 5-1.5 Thr.
87 532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems
90 817 00 06-16 Screw 3/8-16 x 1
94 581 88 09-01 Exhaust Tube
96 819 09 14-16 Washer 9/32 x 7/8 x 16 Ga.
97 817 67 04-12 Screw Thdrol 1/4-20 x 3/4
138 532 41 41-19 Purge Line

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

Engine Power Rating Information

The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual “on-site” or net power). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.

For engine service and replacement parts, call the toll free number for your engine manufacturer listed below:

Briggs & Stratton: 1-800-233-3723

Steering Assembly Components

KEY NO. PART NO. DESCRIPTION
1 532 42 45-43 Wheel, Steering
2 532 43 68-70 Axle Asm., Front
4 532 43 68-73 Spindle Asm., LH
5 532 43 68-74 Spindle Asm., RH
6 532 12 49-31 Washer Thrust 0.75 x 1.23
7 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.
8 812 00 00-29 Ring, Klip #T5304-75
9 532 12 12-32 Cap, Spindle
13 532 12 17-49 Washer 25/32 x 1-1/4 x 16 Ga.
14 539 99 01-18 Washer, SLW ZD 3/8
15 873 54 06-00 Nut, Crown Lock 3/8-24 unf
16 585 86 92-02 Shaft Steering
19 532 19 47-29 Plate Steering
20 532 40 97-63 Boot, Steering
21 532 43 77-47 Adapter, Wheel Steering
22 585 02 99-01 Bearing
26 532 42 46-91 Insert, Wheel Steering
27 819 21 16-16 Washer 21/32 x 1 x 16 Ga.
28 817 00 06-12 Screw 3/8-16 x 3/4
33 539 99 01-87 Lockwasher 5/16
35 532 44 07-70 Gear, Sector Plate
45 819 11 38-12 Washer 11/32 ID x 2-3/8 OD x 12 Ga.
53 532 18 89-67 Washer Hardened.793 x 1.637 x .060
57 532 40 74-65 Bracket Upstop
58 532 19 47-47 Bolt Shoulder Sector Pivot CFM
59 532 19 47-48 Washer Thrust Sector Steering
60 873 97 10-00 Nut Flange Lock 5/8-11
61 532 43 68-84 Draglink, LH
62 532 43 68-85 Draglink, RH
63 817 00 05-12 Screw 5/16-18 x 3/4
64 532 19 98-49 Retainer Clip Spring Steering
66 871 02 07-48 Bolt Hex Fghd 7/16-14 x 3 Serr
67 532 19 47-37 Bushing PM Front Axle
68 873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5
69 532 19 91-62 Washer 1.5 x .505 x .118
70 585 33 88-01 Bracket Deck Susp. Front
71 532 19 07-52 Shaft Extension
72 532 42 89-82 Bolt 5/16-18 x 4
75 580 68 37-01 Pinion
76 580 68 36-01 Screw
80 532 00 13-70 Washer
81 532 43 68-87 Link Cross RH
82 532 44 21-47 Pivot Bolt
85 532 44 18-73 Pivot RH
86 532 44 18-72 Pivot LH
122 532 44 49-62 Cap Gear

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

Mower Deck Components

KEY NO. PART NO. DESCRIPTION
1 532 42 46-96 Mower Housing
6 532 19 51-86 Arm Suspension
7 532 41 63-58 Screw #10 x 0.750 BOS Thread
11 532 13 89-71 Blade, 42" Hi-Lift (For bagging or discharge)
-- 532 13 97-75 Blade, 42" Mulching Premium (For better wear when mulching)
-- 532 13 41-49 Blade, 42" Mulching Std (For mulching mowers only)
-- 532 42 47-52 Blade 42SP" 3N1
-- 532 42 27-19 Blade 42SP" Premium
12 584 30 93-01 Screw Sems 7/16-20 x 1 Hex Head
13 587 25 65-01 Shaft Assembly, Mandrel
14 532 18 72-81 Housing, Mandrel
15 585 32 39-01 Bearing, Ball, Mandrel
19 532 19 65-39 Bolt, Shoulder
20 532 15 97-70 Baffle, Vortex
21 873 68 05-00 Nut, Crownlock 5/16-18 unc
23 532 19 25-57 Bracket, Deflector
24 532 10 53-04 Cap, Sleeve
25 532 19 70-26 Spring, Torsion, Deflector
26 532 11 04-52 Nut, Push
27 532 40 30-04 Shield, Deflector
29 532 13 14-91 Rod, Hinge
32 532 19 74-73 Pulley, Mandrel
33 532 40 02-34 Nut, Toplock, Flanged
34 872 11 06-12 Bolt Carr Sh. 3/8-16 x 1-1/2 Gr. 5
36 532 19 73-79 Pulley, Idler 4.50 RAW
37 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
38 532 43 25-20 Keeper Belt Mandrel
40 873 90 06-00 Nut, Lock Flg. 3/8-16 unc
41 584 95 39-01 Bolt Hex Wsh Hd 313-18 x 1.19
42 532 19 84-10 Spring Torsion Brake
43 532 19 72-56 Spring Torsion Retainer
46 532 13 77-29 Screw Thd Roll 1/4-20 x 5/8
47 532 19 72-50 Bracket Clutch Cable
55 532 43 71-10 Arm, Idler
56 532 19 90-92 Spacer, Retainer
57 817 00 06-16 Screw Hexwsh Thd 3/8-16 x 1
59 532 14 10-43 Guard, Tuv Idler (94)
60 532 19 72-61 Arm Brake Mower
62 872 11 06-16 Bolt Rdhd Sqnk 3/8-16 unc x 2
63 532 19 94-77 Arm Brake Mower
64 532 19 99-18 Linkage Brake
67 532 40 30-12 Handle, Clutch Cable
68 532 42 96-36 V-Belt
69 872 14 05-05 Bolt Rdhd Sqnk 5/16-18 x 5/8
70 532 40 12-46 Clutch Asm. Manual
113 817 00 05-10 Screw 5/16-18
116 532 12 48-42 Bolt Shoulder
117 589 52 74-01 Wheel Gauge
119 819 12 14-14 Washer 3/8 x 7/8 x 14 Ga.
122 532 19 72-58 Keeper Belt Eng. LH
123 532 19 72-59 Keeper Belt Eng. RH
144 532 19 92-04 Keeper Belt
145 532 19 31-97 Pulley Idler Primary
147 532 40 19-71 Spring Return
152 584 24 35-01 Cable Clutch Manual
188 532 1951-61 Stud Fastener
189 873 90 05-00 Nut Lock Hex Flange
192 532 19 72-60 Bracket Brake Stand LH
195 817 00 06-12 Screw Hexwsh Thdr 3/8-16 x 3/4
208 817 67 06-08 Screw THDROL 3/8-16 x 1/2
254 585 31 68-05 Plate Reinforcement Front
255 585 31 70-05 Plate Reinforcement Side
256 539 10 98-00 Carriage Bolt 1/4-20 x 1 Gr. 5
257 873 90 04-00 Nut Hex Flange 1/4-20 unc
-- 587 25 33-01 Mandrel Assembly (Includes housing (key#14), shaft assembly (key#13), and bearing only (key#15) - pulley/nut/washer and blade bolt/washers not included)
-- 501 45 13-01 Replacement Mower, Complete

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

Mower Lift Components

KEY NO. PART NO. DESCRIPTION
2 532 42 20-27 Shaft Asm., Cross Lift
3 532 19 52-31 Lever Asm., Lift RH
7 580 96 23-01 Grip, Lever
10 532 19 63-14 Spring Torsion
87 532 19 42-09 Pin Cotter 7/16 Bow Tie Lock
88 532 41 07-10 Spring Lift Assist
89 819 19 19-12 Washer Clear Zinc
90 532 19 42-08 Pin Cotter 5/16 Bow Tie Lock
91 532 19 79-84 Link Lift Susp Mower Rear
97 817 00 06-12 Screw 3/8-16 x .75 Smgml Tap/R.Z
98 532 42 05-25 Link Lift Susp. Front Mower
100 873 93 06-00 Nut Centerlock 3/8-16 unc
101 581 50 65-01 Link Asm. Fixed
116 819 15 15-16 Washer 15/32 x 15/16 x 16 Ga.

*Key 91 may be substituted for Key 101

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

Seat Assembly Components

KEY NO. PART NO. DESCRIPTION
1 532 19 75-14 Seat
2 532 18 01-66 Bracket Pivot Fender
6 873 80 06-00 Nut, Lock w/Ins. 3/8-16 unc
7 587 61 33-01 Spring, Seat Cprsn
8 532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems
10 532 44 18-05 Pan, Seat
12 532 19 93-70 Bracket Mnt.
13 532 12 12-48 Bushing Snap
14 872 05 04-12 Bolt 1/4-20 x 1-1/2
15 532 13 43-00 Spacer Split
16 532 12 37-40 Spring CPRSN Plate
17 532 12 39-76 Nut Lock 1/4
19 532 19 93-72 Knob Seat
21 587 90 78-01 Bolt, Shoulder 5/16-18 x 5/8
37 873 80 05-00 Nut, Lock 5/16-18 unc
42 532 19 93-71 Cup Washer
46 588 09 04-01 Bolt 3/8-16 x 1; 1.25 OD

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

PDF preview unavailable. Download the PDF instead.

doc000120157 Acrobat Distiller 11.0 (Windows)

Related Documents

Preview Poulan Pro PP175G42 Lawn Tractor Repair Parts Manual
This manual provides detailed repair parts information for the Poulan Pro PP175G42 Lawn Tractor. It includes schematics, electrical diagrams, and parts lists for various components including the chassis, drive system, engine, steering, mower deck, mower lift, seat, and decals. Information on ordering parts and service is also provided.
Preview Poulan PRO PB20H42LT Lawn Tractor Repair Parts Manual
This manual provides a comprehensive parts list and diagrams for the Poulan PRO PB20H42LT Lawn Tractor, aiding in the identification and ordering of replacement parts.
Preview Poulan PRO PRO 925 ZX / 950 ZX Parts Manual
Comprehensive parts manual for Poulan PRO PRO 925 ZX (968999516) and PRO 950 ZX (968999507) zero-turn lawn mowers. Includes detailed diagrams and part lists for chassis, engine, steering, ignition system, hydraulic pump-motor, wheels, tires, deck lift, and decals.
Preview Poulan Pro PR100 Snow Thrower Illustrated Parts List
Detailed illustrated parts list for the Poulan Pro PR100 Snow Thrower, Model Number PR100, Product Number 961 82 00-15, MFG. ID. Number 96182001504. Includes breakdown of Auger Assembly, Chute Assembly, Handle Assembly, Decals, Drive Assembly, Engine Assembly, Frame Assembly, and Shroud Assembly with part numbers and descriptions.
Preview Poulan PRO PP19A42 Lawn Tractor Operator's Manual
Comprehensive operator's manual for the Poulan PRO PP19A42 Lawn Tractor, covering safety rules, operation, maintenance, and troubleshooting. Learn how to safely operate and maintain your lawn tractor for optimal performance.
Preview Poulan Pro PP17G42 Lawn Tractor Repair Parts Manual
Comprehensive repair parts manual for the Poulan Pro PP17G42 Lawn Tractor, detailing schematics, electrical components, chassis, drive, engine, steering, mower deck, and more with part numbers and diagrams.
Preview Poulan Pro PR5020 Chainsaw Spare Parts List
Comprehensive spare parts list for the Poulan Pro PR5020 chainsaw, including model numbers 967061401 and 967061501, with detailed diagrams and part numbers for engine, housing, and side cover/clutch components.
Preview Poulan PRO PB20H42LT Lawn Tractor Repair Parts Manual
This repair parts manual provides detailed diagrams and part numbers for the Poulan PRO PB20H42LT Lawn Tractor. It covers all major components including electrical, chassis, drive, engine, steering, mower deck, mower lift, seat, and decals.