Poulan PRO PB20H42LT Lawn Tractor Repair Parts Manual
This manual is designed to provide the customer with a means to identify the parts on his/her tractor when ordering repair parts. The illustrations may or may not represent the actual assemblies; therefore, it is not recommended to use this manual as a guide to assemble or disassemble the tractor. Some hardware and parts are drawn larger in order to more readily identify them.
Each tractor has its own model number. The model number for your tractor can be found on the fender under the seat.
When ordering parts, always give the following information:
- Product - "Tractor"
- MODEL NUMBER - “PB20H42LT (96042014800)”
- Part Number
- Part Description
Schematic
The tractor is equipped with a special alternator system. The lights are not connected to the battery, but have their own electrical source. Because of this, the brightness of the lights will change with engine speed. At idle the lights will dim. As the engine is speeded up, the lights will become their brightest.
Ignition Switch Positions:
- OFF: M+G+A1
- RUN/OVERRIDE: B+A1
- RUN: B+A1
- LIGHTS: L+A2
- START: B + S + A1
Electrical System
This section details the electrical components of the tractor, including the battery, starter, alternator, switches, lights, and wiring harnesses. Key part numbers and descriptions are provided for each component.
| KEY NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 1 | 532 16 34-65 | Battery |
| 2 | 874 76 04-12 | Bolt Hex Hd 1/4-20 unc x 3/4 |
| 8 | 532 19 32-28 | Box Battery |
| 16 | 532 17 61-38 | Switch Interlock |
| 21 | 532 18 37-59 | Harness Socket Light |
| 22 | 532 00 41-52 | Bulb, Light #1156 |
| 25 | 581 49 80-01 | Cable Starter 6 Ga. BL/Red 14.5 |
| 26 | 532 17 51-58 | Fuse |
| 27 | 873 51 04-00 | Nut Keps Hex 1/4-20 unc |
| 28 | 532 42 16-86 | Cable Ground 18" Rear Battery Blk 6 Ga. |
| 29 | 532 40 15-45 | Switch Seat |
| 30 | 532 19 33-50 | Switch Ign |
| 33 | 532 41 19-33 | Key/Chain |
| 34 | 532 11 07-12 | Switch Light/Reset |
| 40 | 581 02 31-01 | Harness Ign |
| 43 | 532 19 25-07 | Solenoid |
| 55 | 817 06 05-12 | Screw 5/16-18 x 3/4 |
| 71 | 581 02 30-01 | Harness Ign. Chass. |
| 79 | 532 17 52-42 | Socket Asm. Bulb |
| 87 | 532 19 78-02 | Switch Interlock Clutch |
| 90 | 532 43 53-95 | Cover Terminal |
| 92 | 532 19 66-15 | Harness Pigtail Reverse Switch |
| 93 | 532 19 25-40 | Screw Plastic 10-14 x 2.0 |
| 94 | 532 19 18-34 | Modual Reverse ROS |
| 99 | 817 67 04-12 | Screw |
| 106 | 532 17 48-14 | Pal nut |
NOTE: All component dimensions given in U.S. inches (1 inch = 25.4 mm)
Chassis Components
This section details the various chassis components of the tractor, including the dash, hood, grille, engine plate, fenders, and frame. Each part is identified by a key number and part number, with a description.
| KEY NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 5 | 532 41 17-64 | Dash |
| 14 | 532 18 58-47 | Hood |
| 18 | 532 42 67-92 | Grille |
| 34 | 580 91 08-01 | Plate Engine |
| 36 | 817 06 05-12 | Screw 5/16-18 x 3/4 |
| 37 | 532 43 65-23 | Fender |
| 52 | 873 68 05-00 | Nut Lock 5/16-18 |
| 68 | 817 49 05-08 | Screw Thdrol 5/16-18 x 1/2 |
| 130 | 532 41 63-58 | Screw #10 x 0.750 |
| 137 | 532 18 49-21 | Bumper Hood |
| 138 | 532 40 97-30 | Cupholder |
| 150 | 532 18 44-61 | Duct Heat Hood |
| 151 | 532 40 78-07 | Bracket Pivot |
| 152 | 532 19 95-35 | Shield Browning |
| 153 | 532 18 98-37 | Lens Grille |
| 159 | 817 00 06-12 | Screw Hexwsh Thdrol 3/8-16 x 3/4 |
| 162 | 532 14 24-32 | Screw Hex Wsh Hi-Lo 1/4 x 1/2 |
| 175 | 532 19 32-43 | Crossmember |
| 176 | 532 40 07-76 | Screw 10-24 x 5/8 Wshd Qdrx |
| 177 | 532 19 52-28 | Bushing Steering |
| 180 | 532 19 54-57 | Chassis |
| 181 | 532 40 47-96 | Bushing Mtg. Fender Crgo. |
| 182 | 532 19 30-57 | Dash Lower |
| 183 | 874 52 05-20 | Bolt 5/16-18 x 1-1/4 |
| 189 | 817 00 05-12 | Screw 5/16-18 x 3/4 |
| 194 | 873 90 05-00 | Nut Lock Hex Flange 5/16-18 |
| 196 | 532 41 45-79 | Console Asm. Deck Lift |
| 213 | 874 76 05-12 | Bolt 5/16-18 x 3/4 |
| 217 | 532 40 91-67 | Rod Pivot Hood |
| 218 | 532 19 63-95 | X-Piece Hood Step |
| 228 | 532 1951-61 | Stud Fastener |
| 235 | 532 40 61-29 | Spacer Fender |
| 236 | 873 93 05-00 | Nut Center Lock 5/16-18 |
| 287 | 817 60 04-06 | Screw 1/4-20 x 3/8 |
| 302 | 532 18 38-23 | Insert Lens Reflective |
NOTE: All component dimensions given in U.S. inches (1 inch = 25.4 mm)
Drive System
This section covers the drive components of the tractor, including the transaxle, drive belts, pulleys, and related hardware. Part numbers and descriptions are provided for each item.
| KEY NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 1 | - - - - - | Transaxle, Tufftorq K46BA (448348) (Order parts from transaxle manufacturer.) |
| 2 | 532 12 35-83 | Key Square |
| 15 | 819 13 13-16 | Washer 13/32 x 13/16 x 16 Ga. |
| 17 | 532 41 36-78 | Spring, Brake |
| 22 | 532 19 76-60 | Rod Shift |
| 23 | 532 14 08-45 | Knob |
| 29 | 532 40 38-06 | Rod, Brake |
| 33 | 812 00 00-01 | Ring E |
| 35 | 532 19 77-22 | Rod, Brake, Park |
| 42 | 532 12 48-72 | Cover, Foot Pedal |
| 49 | 872 11 06-14 | Bolt |
| 50 | 532 19 43-27 | Pulley Idler Flat |
| 51 | 873 90 06-00 | Lock Nut 3/8-16 |
| 52 | 532 19 43-26 | Idler V-Groove |
| 56 | 532 13 09-69 | V-Belt, Drive |
| 64 | 532 19 62-00 | Shaft Asm. Pedal Brake Control |
| 70 | 532 41 13-29 | Console |
| 73 | 874 49 05-40 | Bolt Hex 5/16-18 x 2-1/2 G5 |
| 74 | 532 14 24-32 | Screw 1/4 x 1/2 |
| 80 | 532 44 06-19 | Strap Torque |
| 99 | 532 41 57-42 | Rod Spring Bypass |
| 116 | 873 90 05-00 | Nut Lock Hex Flange 5/16-18 |
| 125 | 817 00 05-12 | Screw 5/16-18 x 3/4 |
| 143 | 817 49 05-08 | Screw THDROL 5/16-18 |
| 153 | 532 12 47-88 | Retainer Spring 1" |
| 159 | 876 02 04-12 | Pin Cotter 1/8 x 3/4 |
| 160 | 532 16 94-84 | Retainer Clip |
| 161 | 532 10 57-09 | Spring, Return, Clutch |
| 166 | 532 42 91-64 | Nut Push.625 |
| 167 | 532 40 52-57 | Latch Brake Parking |
| 170 | 532 19 43-22 | Keeper Belt Centerspan |
| 171 | 872 11 06-16 | Bolt 3/8-16 unc x 2 |
| 174 | 532 19 72-89 | Nut Push |
| 175 | 532 40 62-08 | Shaft Asm Shift |
| 176 | 532 19 62-14 | Arm Clevis Rod Shift |
| 178 | 532 19 74-56 | Spring Shift |
| 183 | 532 13 70-57 | Spacer Axle |
| 184 | 532 44 15-04 | Handle Parking Brake |
| 185 | 872 11 06-22 | Bolt |
| 186 | 532 19 43-21 | Spacer Retainer |
| 187 | 819 13 32-10 | Washer |
| 188 | 532 19 43-23 | Link Clutch Ground Drive |
| 189 | 532 19 43-17 | Bellcrank Ground Drive |
| 190 | 532 19 43-18 | Keeper Bellcrank Ground Drive |
| 205 | 532 12 17-48 | Washer 25/32 x 1-5/8 x 16 Ga. |
| 211 | 532 19 62-12 | Bushing Shaft |
| 216 | 532 19 61-31 | Bracket Pulley Idler |
| 221 | 532 40 31-87 | Retainer Spring Clip Handle |
| 225 | 532 40 33-19 | Keeper Belt Transaxle |
| 226 | 532 40 15-64 | Bracket Mount Torque |
| 227 | 817 49 05-12 | Screw 5/16-18 x 3/4 |
| 230 | 532 18 89-67 | Washer Harden.793 x 1.637 x 060 |
| 232 | 874 78 07-16 | Bolt 7/16-14 x 1 Gr 5 |
| 233 | 532 40 52-96 | Washer Serrated |
| 279 | 532 40 62-07 | Link Shift |
NOTE: All component dimensions given in U.S. inches (1 inch = 25.4 mm)
Engine Components
This section provides a detailed breakdown of the engine components, including the engine itself, muffler, fuel tank, and related parts. Each part is listed with its key number, part number, and description.
| KEY NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 1 | - - - | Engine Briggs Model No. 331777-2372-G5(438212) (Order parts from engine manufacturer.) |
| 2 | 532 18 86-55 | Muffler |
| 9 | 532 19 43-20 | Keeper Belt Engine |
| 12 | 532 40 54-71 | Pulley Engine |
| 15 | 532 43 30-03 | Tank Fuel |
| 18 | 532 43 85-96 | Cap Fuel |
| 20 | 532 17 05-45 | Control Throttle |
| 21 | 532 41 63-58 | Screw #10 x 0.750 BOS Thread |
| 28 | 532 40 11-37 | Fuel Line |
| 29 | 532 13 71-80 | Spark Arrester Kit |
| 37 | 532 12 34-87 | Clamp Hose |
| 42 | 810 04 07-00 | Washer Lock 7/16 |
| 45 | 873 51 04-00 | Nut Keps Hex 1/4-20 unc |
| 69 | 532 16 52-91 | Gasket |
| 79 | 532 19 23-34 | Screw 5/16-18 x 3/4 |
| 81 | 532 14 84-56 | Tube Drain Oil Easy |
| 82 | 532 42 82-87 | Valve Drain Oil |
| 84 | 817 06 06-20 | Screw 3/8-16 x 1/4 |
| 85 | 532 17 39-37 | Bolt Hex 7/16-20 x 4 Gr. 5 |
| 87 | 532 17 18-77 | Bolt 5/16-18 unc x 3/4 w/sems |
| 90 | 817 00 06-16 | Screw 3/8-16 x 1 |
| 94 | 532 40 54-50 | Exhaust Tube |
| 96 | 819 09 14-16 | Washer 9/32 x 7/8 x 16 Ga. |
| 97 | 817 67 04-12 | Screw 1/4-20 x 3/4 |
| 111 | 532 41 41-19 | Purge Line |
NOTE: All component dimensions given in U.S. inches (1 inch = 25.4 mm)
For engine service and replacement parts, call the toll free number for your engine manufacturer listed below:
Briggs & Stratton 1-800-233-3723
Engine Power Rating Information: The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual “on-site” or net power). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.
Steering System
This section details the steering components, including the steering wheel, axle, spindles, draglinks, and related hardware. Each part is identified with its key number, part number, and description.
| KEY NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 1 | 532 42 45-43 | Wheel, Steering |
| 2 | 532 19 59-68 | Axle Asm., Front |
| 4 | 532 40 30-87 | Spindle Asm., LH |
| 5 | 532 40 30-88 | Spindle Asm., RH |
| 6 | 532 12 49-31 | Washer Thrust 0.75 x 1.23 |
| 7 | 532 12 17-48 | Washer 25/32 x 1-5/8 x 16 Ga. |
| 8 | 812 00 00-29 | Ring, Clip #T5304-75 |
| 9 | 532 12 12-32 | Cap, Spindle |
| 13 | 532 12 17-49 | Washer 25/32 x 1-1/4 x 16 Ga. |
| 14 | 810 04 06-00 | Washer Lock 3/8 |
| 15 | 873 54 06-00 | Nut, Crown Lock 3/8-24 unf |
| 16 | 532 42 93-74 | Shaft Steering |
| 19 | 532 19 47-29 | Plate Steering |
| 20 | 532 41 12-91 | Boot, Steering |
| 21 | 532 18 67-37 | Adapter, Wheel Steering |
| 22 | 532 42 05-37 | Strg. Supt. Lower |
| 26 | 532 42 46-91 | Insert, Wheel Steering |
| 28 | 817 00 06-12 | Screw 3/8-16 x 3/4 |
| 33 | 810 04 05-00 | Washer Lock 5/16 |
| 35 | 532 19 47-32 | Gear, Sector Plate |
| 45 | 819 11 38-12 | Washer 11/32 x 2-3/8 x 12 Ga. |
| 53 | 532 18 89-67 | Washer Hardened .793 x 1.637 x .060 |
| 57 | 532 40 74-65 | Bracket Upstop |
| 58 | 532 19 47-47 | Bolt Shoulder Sector Pivot CFM |
| 59 | 532 19 47-48 | Washer Thrust Sector Steering |
| 60 | 873 97 10-00 | Nut Flange Lock 5/8-11 |
| 61 | 532 19 47-40 | Draglink, LH |
| 62 | 532 19 47-41 | Draglink, RH |
| 63 | 817 00 05-12 | Screw 5/16-18 x 3/4 |
| 64 | 532 19 98-49 | Retainer Clip Spring Steering |
| 66 | 871 02 07-48 | Bolt Hex Fghd 7/16-14 x 3 Serr |
| 67 | 532 19 47-37 | Bushing PM Front Axle |
| 68 | 873 90 07-00 | Nut Lock Flange 7/16-14 Gr. 5 |
| 69 | 532 19 91-62 | Washer 1.5 x .505 x .118 |
| 70 | 532 19 61-97 | Bracket Deck Susp. Front |
| 71 | 532 19 07-52 | Shaft Ext. Steering |
| 72 | 532 42 89-82 | Bolt 5/16-18 x 4 W/Patch |
| 122 | 532 44 49-62 | Cap Gear |
NOTE: All component dimensions given in U.S. inches (1 inch = 25.4 mm)
Mower Deck Components
This section details the components of the mower deck, including the housing, blades, mandrels, pulleys, and associated hardware. Each part is listed with its key number, part number, and description.
| KEY NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 1 | 532 19 64-95 | Mower Housing |
| 6 | 532 19 51-86 | Arm Suspension |
| 7 | 532 41 63-58 | Screw #10 x 0.750 BOS Thread |
| 8 | 532 19 30-03 | Bolt/Washer Asm 7/16-20 unf |
| 11 | 532 13 89-71 | Blade, 42" Hi-Lift (For bagging or discharge) |
| 13 | 532 19 28-72 | Shaft Assembly, Mandrel |
| 14 | 532 18 72-81 | Housing, Mandrel |
| 15 | 532 11 04-85 | Bearing, Ball, Mandrel |
| 19 | 532 19 65-39 | Bolt, Shoulder |
| 20 | 532 15 97-70 | Baffle, Vortex |
| 21 | 873 68 05-00 | Nut, Crownlock 5/16-18 unc |
| 23 | 532 19 25-57 | Bracket, Deflector |
| 24 | 532 10 53-04 | Cap, Sleeve |
| 25 | 532 19 70-26 | Spring, Torsion, Deflector |
| 26 | 532 11 04-52 | Nut, Push |
| 27 | 532 40 30-04 | Shield, Deflector |
| 29 | 532 13 14-91 | Rod, Hinge |
| 30 | 532 17 39-84 | Screw Thdrol Rolling Wsh Hd |
| 31 | 532 18 76-90 | Washer, Spacer |
| 32 | 532 19 74-73 | Pulley, Mandrel |
| 33 | 532 40 02-34 | Nut, Toplock, Flanged |
| 34 | 872 11 06-12 | Bolt Carr Sh. 3/8-16 x 1-1/2 Gr. 5 |
| 36 | 532 19 73-79 | Pulley, Idler 4.50 RAW |
| 37 | 819 13 13-16 | Washer 13/32 x 13/16 x 16 Ga. |
| 38 | 532 43 25-20 | Keeper Belt Mandrel |
| 40 | 873 90 06-00 | Nut, Lock Flg. 3/8-16 unc |
| 42 | 532 19 84-10 | Spring Torsion Brake |
| 43 | 532 19 72-56 | Spring Torsion Retainer |
| 46 | 532 13 77-29 | Screw Thd Roll 1/4-20 x 5/8 |
| 47 | 532 19 72-50 | Bracket Clutch Cable |
| 55 | 532 43 71-10 | Arm, Idler |
| 56 | 532 19 90-92 | Spacer, Retainer |
| 57 | 817 00 06-16 | Screw Hexwsh Thd 3/8-16 x 1 |
| 59 | 532 14 10-43 | Guard, Tuv Idler (94) |
| 60 | 532 19 72-61 | Arm Brake Mower |
| 62 | 872 11 06-16 | Bolt Rdhd Sqnk 3/8-16 unc x 2 |
| 63 | 532 19 94-77 | Arm Brake Mower |
| 64 | 532 19 97-90 | Linkage Brake |
| 67 | 532 40 30-12 | Handle, Clutch Cable |
| 68 | 532 42 96-36 | V-Belt |
| 69 | 872 14 05-05 | Bolt Rdhd Sqnk 5/16-18 x 5/8 |
| 70 | 532 19 83-32 | Clutch Asm. Manual |
| 113 | 817 00 05-10 | Screw 5/16-18 |
| 116 | 532 12 48-42 | Bolt Shoulder |
| 117 | 532 18 86-06 | Wheel Gage |
| 119 | 532 19 72-58 | Keeper Belt Eng. LH |
| 122 | 532 19 72-59 | Keeper Belt Eng. RH |
| 123 | 532 19 92-04 | Keeper Belt |
| 144 | 532 19 31-97 | Pulley Idler Primary |
| 145 | 532 40 19-71 | Spring Return |
| 147 | 532 43 51-11 | Cable Clutch Manual w/Spr. |
| 152 | 532 19 51-61 | Stud Fastener |
| 188 | 532 19 51-61 | Stud Fastener |
| 189 | 873 90 05-00 | Nut Lock Hex Flange |
| 192 | 532 19 72-60 | Bracket Brake Stand LH |
| 195 | 817 00 06-12 | Screw 3/8-16 x 3/4 |
| 196 | 819 12 14-14 | Washer 3/8 x 7/8 x 14 Ga. |
| 241 | 532 15 29-27 | Screw TT #10-32 5 3/8 Flange |
| 242 | 532 41 55-98 | Port Washout |
| - - | 532 41 64-05 | Coupling Quick |
| - - | 532 19 28-70 | Mandrel Assembly (Includes hous- ing, shaft assembly, and bearing only - pulley/nut/washer and blade bolt/washers not included) |
| - - | 532 43 77-30 | Replacement Mower, Complete |
NOTE: All component dimensions given in U.S. inches (1 inch = 25.4 mm)
Mower Lift Components
This section details the components of the mower lift system, including shafts, levers, springs, and pins. Each part is identified with its key number, part number, and description.
| KEY NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 2 | 532 42 20-27 | Shaft Asm., Cross Lift |
| 3 | 532 19 52-31 | Lever Asm., Lift RH |
| 7 | 580 96 23-01 | Grip, Lever |
| 10 | 532 19 63-14 | Spring Torsion |
| 87 | 532 19 42-09 | Pin Cotter 7/16 Bow Tie Lock |
| 88 | 532 41 07-10 | Spring Lift Assist |
| 89 | 819 19 19-12 | Washer Clear Zinc |
| 90 | 532 19 42-08 | Pin Cotter 5/16 Bow Tie Lock |
| 91 | 532 19 51-81 | Link Lift Susp Mower Rear |
| 97 | 817 00 06-12 | Screw 3/8-16 x .75 Smgml Tap/R.Z |
| 98 | 532 19 52-70 | Link Lift Susp. Front Mower |
| 100 | 873 93 06-00 | Nut Centerlock 3/8 -16 unc |
| 101 | 532 40 70-03 | Link Asm. Lift Fixed |
NOTE: All component dimensions given in U.S. inches (1 inch = 25.4 mm)
Seat Components
This section lists the parts for the tractor seat assembly, including the seat, bracket, strap, pan, and springs. Key numbers, part numbers, and descriptions are provided.
| KEY NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 1 | 532 19 75-14 | Seat |
| 2 | 532 18 01-66 | Bracket Pivot Fender |
| 3 | 532 14 06-75 | Strap, Asm Fender |
| 6 | 873 80 06-00 | Nut, Lock w/Ins. 3/8-16 unc |
| 7 | 532 12 41-81 | Spring, Seat Cprsn |
| 8 | 532 17 18-77 | Bolt 5/16-18 unc x 3/4 w/Sems |
| 10 | 532 19 69-77 | Pan, Seat |
| 21 | 532 17 18-52 | Bolt, Shoulder 5/16-18 |
| 37 | 873 80 05-00 | Nut, Lock 5/16-18 unc |
| 40 | 532 19 76-61 | Handle Slide |
| 41 | 532 19 82-00 | Spring Latch |
| 43 | 874 76 06-12 | Bolt 3/8-16 unc x 3/4 |
| 44 | 819 13 38-12 | Washer 13/32 x 2 3/8 x 12 Ga. |
NOTE: All component dimensions given in U.S. inches (1 inch = 25.4 mm)
Decals
This section lists all the decals for the tractor, including warning decals, model decals, and instructional decals. Each decal is identified by its part number and description.
| KEY NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 1 | 532 17 05-63 | Decal, Mower Warning |
| 2 | 532 42 95-51 | Decal Eng. H.P. |
| 3 | 532 44 52-35 | Decal Hood |
| 4 | 581 53 27-01 | Decal Side Panel |
| 7 | 581 50 34-01 | Decal Replacement Parts |
| 8 | 532 41 16-57 | Decal Fender Warn S/F |
| 9 | 532 44 52-34 | Decal Fender Logo |
| 11 | 532 43 85-01 | Decal Ins Strg Whl |
| 12 | 532 43 84-92 | Decal Fend SD |
| 14 | 532 16 03-96 | Decal V-Belt Schematic |
| 20 | 532 14 50-05 | Decal Bat Dan/Psn |
| - - | 532 16 69-60 | Decal Bypass |
| - - | 532 40 95-05 | Pad Footrest LH |
| - - | 532 41 12-73 | Pad Footrest RH |
| 115 | 52 73-27 | Manual Operator's (E/S) |
| 583 97 12-33 | Manual Parts (E/S) |
Wheels and Tires
This section provides details on the wheels and tires for the tractor, including valve caps, stems, rims, tubes, and tires. Part numbers and descriptions are included.
| KEY NO. | PART NO. | DESCRIPTION |
|---|---|---|
| 1 | 532 05 91-92 | Cap Valve Tire |
| 2 | 532 06 51-39 | Stem Valve |
| 3 | 532 43 96-73 | Rim Asm 6" Front |
| 4 | 532 05 99-04 | Tube Front (Service Item Only) |
| 5 | 532 10 62-22 | Tire FT 15 x 60-6 |
| 6 | 532 12 49-57 | Fitting Grease |
| 7 | 532 12 49-59 | Bearing Flange (Front Wheel Only) |
| 8 | 532 17 50-39 | Cap Axle |
| 9 | 532 13 84-68 | Tire RT 20 x 8-8C |
| 10 | 532 12 49-26 | Tube Rear (Service Item Only) |
| 11 | 532 44 08-81 | Rim Asm 8" Rear Service |
| - - | 532 14 43-34 | Sealant, Tire (Not Shown) |
NOTE: All component dimensions given in U.S. inches (1 inch = 25.4 mm)
Limited Warranty
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations and exclusions.
- This warranty does not apply to the engine, transaxle/transmission components, battery (except as noted below) or components parts thereof. Please refer to the applicable manufacturer's warranty on these items.
- Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser unless such return is requested by the manufacturer.
- Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we will exchange the Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must be maintained in accordance with the instructions furnished.
- The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original purchase.
- This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accordance with the instructions furnished. This Warranty does not apply to any product which has been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.
- Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, standard hardware and normal maintenance.
- In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please contact:
HOP
Outdoor Products Customer Service Dept.
9335 Harris Corners Parkway
Charlotte, NC 28269 USA
In Canada contact:
HOP
5855 Terry Fox Way
Mississauga, Ontario
L5V 3E4
giving the model number, serial number and date of purchase of your product and the name and address of the authorized dealer from whom it was purchased.
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from locale to locale.
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
Parts and Service
This product has been expertly engineered and carefully manufactured to rigid quality standards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit.
- For Parts and service, contact our authorized distributor: call 1-800-849-1297
- For replacement parts, have available the following information:
- a. Model Number/Manufacturer's I.D. Number
- b. Description of part.
- For Technical Assistance: call 1-800-829-5886
- For a Parts Manual, go to our website: www.poulanpro.com
NOTE: HOP provides parts and service through its authorized distributors and dealers; therefore, all requests for parts and service should be directed to your local dealer(s). The philosophy of HOP is to continually improve all of its products. If the operating characteristics or the appearance of your product differs from those described in this Manual, please contact your local dealer for updated information and assistance.
