Kogan Active+ Lite Smart Watch User Guide

Safety & Warnings

Battery Warning

Do not disassemble, bore or damage the battery. Do not disassemble the built-in batteries of non-replaceable battery devices. Do not use sharp objects to remove the battery.

Health Warning

• If you are wearing a pacemaker or other implanted electronic devices, please consult your doctor before using the heart rate monitoring strap.
• The watch's optical heart rate sensor glows green and flashes. If you suffer from epilepsy or are sensitive to blinking light sources, please consult your physician if you can wear this product.
• The device tracks your daily activities through sensors. These data are intended to tell you about your daily activities, such as steps, sleep, distance, heart rate and calories, but may not be completely accurate.
• The device, accessories, heart rate sensors and other relevant data are designed for entertainment and fitness, not for medical purposes. They are not applicable to the diagnosis, monitoring, treatment or prevention of any diseases or symptoms. The heart rate data is for reference only. It is not responsible for any consequences caused by any data deviation.

Cycling Warning

Please always maintain good judgment and ride in a safe manner. Make sure your bike and hardware are properly maintained and all components are properly installed.

Matters Needing Attention

• Watch data needs to be kept once every 7 days to avoid data loss.
• The watch has no waterproof effect on seawater, acidic and alkaline solutions, chemical reagents and other corrosive liquid. The damage or defects caused by misuse or improper use are not covered by the warranty.
• Sports mode supports up to 6 hours of exercise at a time.
• The watch has a waterproof level of 5ATM and supports cold water shower, swimming, but not diving.
• Avoid wearing the watch too tight in daily use. Please keep the parts of the watch touching the skin dry.
• When your heart rate is measured, keep your arm still during the test.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could avoid the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Overview

1. Power on

The device will turn on automatically after charging.

Image: Diagram showing the Kogan Active+ Lite Smart Watch being connected to a charger.

Note: The device must be charged and activated before the first use. Always use the original power adapter to charge the device.

2. Download and install VeryFitPro

You can directly scan the QR code to download VeryFitPro or search "VeryFitPro" in the App Store/Play Store to download and install.

Image: QR code for downloading the VeryFitPro app.

Hardware requirements by platform:

• iOS 8.0 and above
• Android 4.4 and above
• Bluetooth 4.2

3. Connect via Bluetooth

Correct operation: Pair the Watch via the VeryFitPro app on the phone.

Incorrect operation: Pair the Watch directly via Bluetooth in the phone's settings menu.

Image: Side-by-side comparison of correct and incorrect Bluetooth pairing methods for the watch. The correct method shows pairing through the VeryFitPro app, while the incorrect method shows pairing through the phone's Bluetooth settings.

4. Device Pairing

Drop down on the app's home screen to show the pairing request. Select the product model and tap "Confirm Binding" to pair.

Image: Screenshots of the VeryFitPro app showing the device pairing process, including selecting the device from a list and confirming the binding.

Notes

• On iOS only, proceed to the phone's regular Bluetooth settings and search and pair to the watch.
• During pairing, VeryFitPro will prompt you to enable GPS and Bluetooth and authorize VeryFitPro to get access to the GPS on your mobile phone.

Syncing Data

The watch will collect various data during use. To sync data, connect the watch with Bluetooth and open the app: swipe down and the sync prompt will appear.

Image: Screenshot of the VeryFitPro app showing the data syncing interface, with a finger swiping down to initiate the sync.

Notes:

• Sync data at least once within 7 days to avoid data loss.

Fitting

Image: Diagram showing how to wear the Kogan Active+ Lite Smart Watch on a wrist, indicating the correct placement and tightness.

Wear the device a finger's distance from the wrist and adjust the tightness of the wristband to a comfortable position.

Note: Wearing too loosely may affect the accuracy of heart rate data.

Strap replacement

Image: Diagram showing the back of the Kogan Active+ Lite Smart Watch with a switch highlighted for strap removal.

Flip the switch and to remove the strap for replacement.

Operation

Button operation

Image: Illustration of the Kogan Active+ Lite Smart Watch with callouts indicating button functions. The right button is described as returning to the previous interface or pressing and holding to enter/confirm.

Changing watch interface

Image: Illustration showing how to change the watch face by pressing and holding the main dial.

Press and hold while on the main dial to bring up alternate interfaces to select from.

Main interface

Swipe on the screen to enter the relevant interface.

Image: A circular arrangement of icons representing different functions of the smart watch: Status, Notifications, Function List, and Data.

• Status: Displays activity, sleep, and heart rate information.
• Notifications: Shows incoming messages and alerts.
• Function List: Includes Sport, Heart rate, Relax, and Alarm options.
• Data: Displays steps and progress towards a daily goal.

Icon functions

Note: For more functions (sleeping) and operation, please check the VeryFitPro software of the mobile phone. Try to ensure that the box fits appropriately.

Sport mode

To record sport activity:

1. Click the sports icon and select activity type and the countdown timer will begin.
2. Press the right button to pause/resume timer.
3. Press and hold the right button to stop the timer and press the end button to exit sport mode.

Women's health tracking

Image: Screenshot of the smart watch displaying women's health tracking data, showing days until the next period and ovulation prediction.

Used for recording menstrual changes, tracks individual menstrual cycle and predicts ovulation. This function must be enabled on the app.

Cleaning & Care

Image: Diagram showing a hand wiping the Kogan Active+ Lite Smart Watch screen with a cloth.

To ensure product function, the following points should be observed:

• Keep the watch clean and dry.
• Do not wear the watch too tightly.
• Do not use household cleaners to clean the watch; instead, use a soap-free detergent.
• Alcohol can be used to scrub stains that are not easy to remove.

Troubleshooting

Cannot locate watch in app search

• Update VeryFitPro to the latest version.
• Close all programs, disconnect and reconnect Bluetooth.
• Confirm operating system is Android 4.4 / iOS 8.0 or above.

Notification/text/phone call not received

• Enable smart reminder function/call reminder switch in app and synchronize to watch.
• Ensure mobile device is paired via Bluetooth.

Bluetooth disconnects

• Ensure distance is not greater than 7 metres.
• Ensure there are no obstructions – note that metal jewellery, etc. can interfere with Bluetooth signal.
• Ensure mobile phone's Bluetooth function is working.

FAQ & Tips

Data backup

• Synchronise data at least once per 7 days as the watch retains data for 7 days.

Factory reset

• Pair watch through the app and reset though Device Model > More Settings.

Do I need to keep my Bluetooth on when I wear my watch?

• For the pedometer, sleeping and alarm clock functions, a Bluetooth connection is not required and you can sync data later.
• For the call alert, message alert and find my phone functions, Bluetooth must be connected.

For further troubleshooting steps, see the Help and Feedback setup in Image: Person icon section within the app.

Disposal

Image: Symbol indicating that the appliance should not be disposed of with household waste.

This marking indicates that this appliance should not be disposed of with other house-hold wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

Notes

Blank lined section for user notes.