i-PRO WV-S1536 Series Network Camera Installation Guide

installation guide for i-PRO models including: WV-S1536LTN, WV-S1536LTN Network Camera, Network Camera, Camera

File Info : application/pdf, 25 Pages, 4.21MB

PGQP3734ZAC1 WV-S1536LTN IG en

Installation Guide
Included Installation Instructions

Network Camera For professional use only
Model No. WV-S1536LTN WV-S1536LT

Outdoor use

WV-S1536LN

WV-S1536L

WV-S1536LTN

WV-S1536LNS (Heavy salt damage resistance)

About the user manuals
Product documentation is composed of the following documents.
· Installation Guide (this document): Provides information about "Precautions", "Precautions for installation" and the installation method.
· Basic Information (in the following manual website): Provides information about "Precautions for use", "Parts and functions" and "Detail specifications".
· Operating Instructions (in the following manual website): Explains how to perform the settings and how to operate this camera. https://i-pro.com/products_and_solutions/en/surveillance/documentation-database

"<Control No.: C****>" used in these documents should be used to search for information on our technical information website (https://i-pro.com/products_and_solutions/en/surveillance/learning-and-support/ knowledge-base/technical-information) and will guide you to the right information.

· Before attempting to connect or operate this product, please read these instructions carefully and save Important Safety Instructions leaflet for future use.

· microSDXC/ microSDHC/ microSD memory card is described as microSD memory card.

· The external appearance and other parts shown in this manual may differ from the actual product within the

scope that will not interfere with normal use due to improvement of the product.

Authorised Representative in EU: i-PRO EMEA B.V. Laarderhoogtweg 25, 1101 EB Amsterdam, Netherlands

Tokyo, Japan https://www.i-pro.com/

i-PRO EMEA B.V. UK Branch 1010 Cambourne Business Park, Cambridgeshire CB23 6DP

C0224-0 PGQP3734ZA

Disposal of Old Equipment and Batteries Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation. By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment. For more information about collection and recycling, please contact your local authority. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. Note for the battery symbol (bottom symbol) This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

For U.S.A.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Supplier's Declaration of conformity Trade name : i-PRO Model No. : WV-S1536LTN, WV-S1536LT
WV-S1536LN, WV-S1536L Responsible Party : i-PRO Americas Inc. 8550 Fallbrook Drive, Suite 200 Houston, Texas 77064 Support Contact: 1-800-513-5417

For U.S.A. The model number and serial number of this product may be found on the surface of the unit. You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft.
Model No. Serial No.
For Canada CAN ICES-3(A)/NMB-3(A)

For U.S.A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

About notations

The following notations are used when describing the functions limited for specified models.

The functions without the notations are supported by all models.

S1536LT : WV-S1536LTN/WV-S1536LT

S1536LNS : WV-S1536LNS

W : i-PRO white body

S1536L : WV-S1536LN/WV-S1536L

B : black body

Caution:
· The DC power supply connected to the camera must be in the same building.
· The network camera is only intended for a connection to an ethernet or PoE network without routing to the outside plant.
· This product has no power switch. Be sure to install disconnect devices such as a circuit breaker to shut down the main power of power supplying equipment to this product.
· Only connect 12 V DC Class 2 power supply (UL 1310/CSA 223), limited power source (IEC/ EN/UL/CSA 60950-1, IEC/EN/UL/CSA 623681 Annex Q) or IEC/EN/UL/CSA 62368-1 PS2.
· Before attempting to connect or operate this product, please read these instructions carefully.

Notice:
· This product is not suitable for use in locations where children are likely to be present.
· Do not install this product in locations where ordinary persons can easily reach.
· This product is a professional equipment. · For information about screws and other
parts required for installation, refer to the corresponding section of this document.
: Direct current symbol

Precautions
Do not insert any foreign objects. Fire or electrical shock may be caused if water or any foreign objects, such as metal objects, enter inside the unit. Turn the power off immediately and contact qualified service personnel for service. Do not use this product in an inflammable atmosphere. Failure to observe this may cause an explosion resulting in injury.
S1536LT S1536L Avoid installing this product in the locations where salt damage occurs or corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and injury or accidents due to a fall of the product may occur.
S1536LNS Avoid installing this product in the locations where corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and injury or accidents due to a fall of the product may occur. Do not strike or give a strong shock to this product. Failure to observe this may cause injury or fire. Keep microSD memory cards away from infants and children. Otherwise, they may swallow the cards by mistake. In this case, consult a doctor immediately. Do not hang down from this product or use this product as a pedestal. Failure to observe this may cause injury or accidents. Do not damage the power cable.
Do not damage, fabricate, twist, stretch, bundle, or forcibly bend the power cable. Do not place heavy objects on it, and keep it away from heat sources. Use of a damaged power cable may cause electric shock, short circuit, or fire. Consult the dealer for repair. Do not install this product on a place that is greatly influenced by wind. Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or more may cause a fall of the product resulting in injury or accidents.
3

Do not sprinkle more water, exceeding the performance limit of waterproof with a high pressure cleaning machine, etc.
Fire or electrical shock may be caused by immersion. Do not attempt to disassemble or modify this product. Failure to observe this may cause fire or electric shock. Consult the dealer for the repair or inspections. Do not install or clean the camera, or touch this product, the power cable or the
connected cables during thunder storms. Failure to observe this may cause electric shock. Refer installation work to the dealer. Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer. Stop the operation immediately when something is wrong with this product. When smoke goes up from the product, the smell of smoke comes from the product, or the exterior of the product has deteriorated, continued use will cause a fire or fall of the product resulting in injury, or damage to the product. In this case, turn the power off immediately and contact qualified service personnel for service. Select an installation area that can support the total weight. Selecting an inappropriate installation surface may cause this product to fall down or topple over, resulting in injury or accidents. Installation work shall be started after sufficient reinforcement. Periodic inspections shall be conducted. Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents. Consult the dealer for the inspections. The exclusively designed mount bracket shall be used. Failure to observe this may cause a drop resulting in injury or accidents. Use the exclusively designed mount bracket for installation. The screws and bolts must be tightened to the specified torque. Failure to observe this may cause a drop resulting in injury or accidents. Turn the power off when do wiring of this product. Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring may cause fire. Install this product in a location high enough to avoid people and objects from
bumping the product. Failure to observe this may cause injury. Do not install this product in locations subject to vibration. Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents. Correctly perform all wiring. Short circuits in the wiring or incorrect wiring may cause fire or electrical shock. The measures of protection against snowfall shall be taken. Weight of snow may cause a fall of the product resulting in injury or accidents. Protect the product against snowfall by installing it under eaves. Install the product securely on an installation surface in accordance with the
installation instructions. Failure to observe this may cause injury or accidents. Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury. Turn the power off when cleaning this product. Failure to observe this may cause injury.
4

Open Source Software
· This product contains open source software licensed under GPL (GNU General Public License), LGPL (GNU Lesser General Public License), etc.
· Customers can duplicate, distribute and modify the source code of the software under license of GPL and/or LGPL.
· For details concerning licensing and source code of open source software, click "Click here for OSS information" on "Support" page of the setup menu of this product and read the displayed content.
· Please note that we shall not respond to any inquiries regarding the contents of the source code.
Copyright
Except for open source software licensed under GPL/LGPL and so on, distributing, copying, disassembling, reverse compiling and reverse engineering of the software provided with this product are all expressly prohibited. In addition, exporting any software provided with this product violating export laws is prohibited.
Trademarks and registered trademarks
· Microsoft, Windows, Windows Media, Microsoft Edge, and ActiveX are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
· Intel and Intel Core are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
· Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe in the United States and/or other countries.
· microSDXC Logo is a trademark of SD-3C, LLC. · iPad and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. · Android and Google Chrome are trademark of Google LLC. · Firefox is a trademark of the Mozilla Foundation in the US and other countries. · The word "QR Code" is a registered trademark of DENSO WAVE INCORPORATED in Japan and other
countries. · All other trademarks identified herein are the property of their respective owners.
Precautions for installation
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
In order to prevent injury, the product must be securely mounted to an installation surface according to Installation Guide.
Installation area for this product Select an appropriate place for the installation area (such as a strong installation surface) in your particular environment. · Make sure that the installation area is strong enough to hold this product, such as a concrete ceiling. · Install the camera in the foundation area of the architecture or where sufficient strength is assured. · Do not mount the product on a plaster board or a wooden section because they are too weak. If the
product is unavoidably mounted on such a section, the section shall be sufficiently reinforced. · S1536LNS The camera has heavy salt damage resistance treatment applied, but this does not ensure
complete resistance against corrosion. Please pay attention to the installation location such as in places where seawater does not splash directly. Prepare heavy salt damage resistance treatment for the foundation of the installation site, and installation support such as pole mounts. Do not place this product in the following places · Locations where a chemical agent is used such as a swimming pool · Locations subject to moisture or oil smoke such as a kitchen
5

· Locations that have a specific environment that is subject to an inflammable atmosphere or solvents
· Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated · S1536LT S1536L Locations near coasts directly subjected to sea breezes, or locations subject to
corrosive gases such as from hot springs, volcanic regions, etc.
· S1536LNS Locations subject to corrosive gases such as from hot springs, volcanic regions, etc.
· Locations where the temperature is not within the specified range
· Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not designed for on-vehicle use.)
· Locations subject to condensation as the result of severe changes in temperature
· Locations near rubber products (packing, rubber feet, etc.) Screw tightening Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively. Installing in low temperature environments This product is equipped with an internal heater unit for use in cold climates. The heater unit turns on automatically when the temperature inside the product drops below around 15°C {5 °F}. When this product is installed and operated in low temperatures below 20 °C {4 °F}, it may require time to start up since the camera will wait to be warmed up internally by the internal heater right after the power is turned on. Also, the camera may not function properly, if it is installed and operated in an environment where the temperature is below -25 °C {-13 °F}. In such a case, wait approximately 2 hours or more until the camera is warmed up. Then, turn on the power again. As the camera warms up, snow or frost accumulated on the front panel will melt. However, it may not be defrosted from the cover depending on the ambient temperature or weather condition. About reflection of light from outside or IR light A ghost may appear on the screen depending on the incident angle of external light. In the case of using the IR light, installation of a camera near a wall may cause reflection of infrared rays resulting in a part of the screen or the entire screen turning whitish.
· Refer to our technical information website <Control No.: C0109> for image examples and measures to take.
Take notice of humidity Install this product when the humidity is low. If installation is performed when it is raining or in very humid conditions, the inside may be affected by humidity, causing mist-over inside the front panel. Protection from lightning When cables are used outdoors, there is a chance that they may be affected by lightning. In such a case, install a lightning arrestor close to the camera, and make the length of the network cable between the camera and lightning arrestor as short as possible to prevent the camera from being affected by lightning. When noise disturbance may happen Noise may appear in video or audio near a strong electric field from a TV or radio antenna, motors and transformers, or a strong electric field/magnetic field from a power line (lamp line) of AC100 V or more. Conduct the power distribution work to keep 1 m {3.28 feet} away from them or conduct the electric conduit work using metal pipes. (Be sure to make ground connection of the metal pipes.) Make sure to remove this product if it will no longer be used. This product has no power switch. When turning off the power, disconnect the power supply from the 12 V DC power supply or the PoE device. About the battery A battery is installed inside the camera. Do not leave the battery exposed in environments of excessive heat as a result of sunlight or fire. Equipment classification and power source indication label Remove the front part of the unit and refer to the indication label on the bottom side of this unit for the equipment classification, power source, and other information. About static electricity Before installing removing this product, be sure to touch metal objects to discharge static electricity from your body.
6

Specifications* *For further information, refer to the Basic Information.

Power source *1: Power consumption *1:

12 V DC PoE (IEEE802.3af compliant)
S1536LT 12 V DC: 900 mA/ Approx. 10.8 W PoE 48 V DC: 220 mA/ Approx. 10.6 W (Class 0 device)
S1536L 12 V DC: 710 mA/ Approx. 8.5 W PoE 48 V DC: 190 mA/ Approx. 9.1 W (Class 0 device)
S1536LNS

Operating environment Ambient operating temperature:
Ambient operating humidity:

40 °C to +60 °C *2 {40 °F to +140 °F} (Power On range: 30 °C to +60 °C {22 °F to +140 °F}) 10 % to 100 % (no condensation)

Storage environment

Storage temperature: 30 °C to +60 °C {22 °F to +140 °F} Storage humidity: 10 % to 95 % (no condensation)

Monitor output

VBS: 1.0 V [p-p]/75 , composite, Pin jack

(for adjustment):

An NTSC or PAL signal can be outputted from camera

(either press the INITIAL SET button quickly (within 1 second) or

use software to select NTSC or PAL signal).

EXT I/O terminals:

ALARM IN 1 (Alarm input 1/ Black & white input/ Auto time adjustment input) (x1) ALARM IN 2 (Alarm input 2/ ALARM OUT) (x1) ALARM IN 3 (Alarm input 3/ AUX OUT) (x1)

Audio input:

ø3.5 mm stereo mini jack

For microphone input: Recommended applicable microphone: Plug-in power type

(Sensitivity of microphone: -48 dB±3 dB (0 dB=1 V/Pa, 1 kHz)) Input impedance: Approx. 2 k (unbalanced)

Supply voltage: 2.5 V ±0.5 V For line input: Input level: Approx. 10 dBV

Audio output *3:

ø3.5 mm stereo mini jack (Audio output is monaural.) Output impedance: Approx. 600 (unbalanced) Output level: 20 dBV

Waterproof *4:

IP66 (IEC 60529), Type 4X (UL50E) NEMA 4X compliant

Shock resistance:

IK10 (IEC 62262)

Wind resistance:

Up to 40 m/s {approx. 89 mph}

Dimensions:

133 mm (W) × 133 mm (H) × 383 mm (L) {5-1/4 inches (W) × 5-1/4 inches (H) × 15-3/32 inches (L)}

Mass: Finish:

Approx. 2.4 kg {5.3 lbs}

Main body:

Aluminum die cast and resin, W B

Aluminum die cast (The heavy salt damage

resistance coating) and resin, W

<WV-S1536LNS>

Outer fixing screws: Stainless steel (Corrosion-resistant treatment)

Front panel:

PC resin, Clear

(with ClearSight coating) <WV-S1536LTN><WV-S1536LN>

<WV-S1536LNS>

*1 Refer to our technical information website <Control No.: C0106> for further information about Power source and Power consumption information.
*2 When using with the IR LED light constantly lit, the upper limit of the operating temperature range is +50 °C {+122 °F}.

*3 The audio output can be switched to the monitor output. Refer to the "Operating Instructions" on our support website for descriptions of how to switch the output.
*4 Only when installation work is properly performed according to the Installation Guide and appropriate waterproof treatment is performed.
Optional accessories
The latest information Technical information website "Accessory Selector" <Control No.: C0501>
Troubleshooting
Before requesting service, refer to "Troubleshooting" of Basic Information and Operating Instructions. Then, confirm the trouble.
8

Standard accessories
Important Safety Instructions............................ 1 pc.

Adapter box ×1

Grommet cover ×1

Adapter box mounting pin ×1

Mounting screw M4×8 mm {5/16 inches}×2 Grommet ×2 (of them, 1 for spare) (of them, 1 for spare)
<WV-S1536LTN> <WV-S1536LN> <WV-S1536LNS>
Rain wash coating label ×1 (with ClearSight coating)

RJ45 cap ×1

Other items that are needed (not included)

Mounting screws
Installation method Directly mount the camera onto the installation surface.
Mount the camera to a two-gangbox/junction box. Mount the camera using the exclusively designed mount bracket.

Recommended screw*1

Minimum pull-out strength*2

M4 × 16 mm
{5/8 inches} × 4 pcs.*3, *4

724 N {163 lbf}

Refer to the operating instructions of each

bracket.

*1 Select screws according to the material of the location that the camera will be mounted to. In this case, wood screws and nails should not be used.
*2 This value indicates the minimum pull-out strength required value per screw. For information about the minimum pull-out strength, refer to our technical information website <Control No.: C0120>.
*3 The screw length is an example when installing the camera on a robust installation surface with a thickness of 20 mm {25/32 inches} or more.
*4 Please consider using anti-corrosive mounting screws or caulking. Ethernet cable with RJ45 plug (category 5e or better, straight, all 4 pairs (8 pins), less than 100m {328 feet})
As necessary, audio input cable, audio output cable, alarm I/O cable, power supply cable
5 mm {3/16 inches} hexagon wrench

Installation Procedure

Technical Support Video

Parts and functions
Indicators/Buttons Arm

YAW

Name plate

lock screw

Front part (External: sunshade, Internal: main case)

TILT lock screw

PAN lock screw

Adapter box
Grommet Side cable cover access hole*

* Conduit connection part

(Compliant with CTG22 of JIS C 8305 (conduit tube threads), or G3/4 of JIS B 0202 (parallel pipe threads))

Indicators/Buttons
WIDE+AF button TELE+AF button SD ON/OFF button

: Lights

: Blinks

: Lights off

INITIAL SET button

ACT indicator (green)

SD MOUNT indicator (green)

LINK indicator (orange)

MONITOR OUT terminal

· Operating Instructions [Indicator] All LEDs forced to turn off
10

Installation method

For installing on a ceiling

For desktop use

For installing on a wall
Example of explanation for installation 11

Step 1
Common

Preparations
Use only for image rotation

Step 1 Preparations (continued)
When using a microSD card
microSD A click sound is heard.

· Operating Instructions "Format" · It is recommended to use a microSD memory card for i-PRO devices.
13

Step 1 Preparations (continued)
When using an I/O cable (WV-QCA501A: option)
Grommet cover (accessory)
Grommet
14

Step 2

Vertical direction Horizontal direction

83.5 mm {3-9/32 inches} (82.5 mm {3-1/4 inches})

46 mm {1-13/16 inches} (47.6 mm {1-7/8 inches})

83.5 mm {3-9/32 inches} (82.5 mm {3-1/4 inches})

C 83.5 mm {3-9/32 inches} (83.3 mm {3-9/32 inches})

83.5 mm {3-9/32 inches} (83.3 mm {3-9/32 inches})

E 63 mm {2-15/32 inches} 63 mm {2-15/32 inches}

F 85.7 mm {3-3/8 inches} 85.7 mm {3-3/8 inches}

17.3 mm {11/16 inches}

Technical information website "Countermeasure for Lightning Surge" <Control No.: C0121>

M3×8 mm {5/16 inches} Screw with spring washer Recommended tightening torque:

Cable access hole (ø27 mm {ø1-1/16 inches})

0.69 N·m {0.51 lbf·ft}

Conduit cable access hole

M4 (4 pcs./2 pcs.) (locally procured)
15

Ground wire (locally procured)
Minimum pull-out strength: 724 N {163 lbf} (per 1 pc.)

Step 3

Preparations for connecting RJ45 network cable

Grommet (accessory)

RJ45 cap (accessory)
Inside

Outside

Center

Reuse

RJ45 Ethernet (PoE) category 5e or better, straight, 4 pairs (8 pins) < 100 m {328 feet}

ø5 mm to ø8.5 mm {ø3/16 inches to ø11/32 inches}

Outside

150 mm {5-29/32 inches}

Inside

When using an I/O cable (WV-QCA501A: option)

Audio in (white)

< 1 m {3.28 feet} (Mic) < 10 m {32.8 feet} (Line)

Audio out (black) Monitor out
EXT I/O

< 10 m {32.8 feet}
4P alarm cable (accessory of WV-QCA501A)

12 V DC

2P power cable (accessory of WV-QCA501A)

I/O cable (WV-QCA501A: option)

GND (black)
ALARM IN3 (gray)
A ALARM IN2 (red)
ALARM IN1 (green)
12 V DC (red) GND (black)

· Stretch the waterproof tape by about twice the length to use.
· To shorten the tape winding portion, wind the tape while keeping the audio cable slack. Approx. 20 mm {25/32 inches}
Approx. 20 mm {25/32 inches}
Waterproof tape (accessory of WV-QCA501A)
17

Step 4

The following illustrations are examples when connecting only the RJ45 network cable.

Left-hand opening

Grommet cover (At the time of shipment from the factory,
a grommet is attached in the left hole.)

LAN

Right-hand opening

· When installing with a right-hand opening, move a grommet in the left hole to the right hole.

LAN
18

Step 5

The following illustrations show examples of installation for a left-hand opening.

Adapter box mounting pin (accessory)

Mounting screw (accessory)
Recommended tightening torque: 0.69 N·m {0.51 lbf·ft}
19

Step 6

Grommet cover (accessory)

0.69 N·m {0.51 lbf·ft}
20

Step 7

LAN cable

Inside

Outside

I/O cable (WV-QCA501A: option)

2.45 N·m {1.81 lbf·ft}
5 mm {3/16 inches} hexagon wrench (locally procured)
21

Step 8

* Coarsely adjust the camera direction before adjusting it. The following is an example with the camera direction turned to the right.
5 mm {3/16 inches} hexagon wrench (locally procured)

Step 9 Power On (12 V DC/PoE)

TELE+AF

WIDE+AF

Readjustment Step 8

5 mm {3/16 inches} hexagon wrench (locally procured)

YAW TILT

PAN

PAN lock screw: 2.7 N·m {1.99 lbf·ft} TILT lock screw: 4.3 N·m {3.17 lbf·ft} YAW lock screw: 2.7 N·m {1.99 lbf·ft}
23

Step 10

"" mark

OPEN

LOCK

0.69 N·m {0.51 lbf·ft}
24

Step 11

Technical information website "IP Setting Software" <Control No.: C0123> or "i-PRO Configuration Tool (iCT)" <Control No.: C0133>
"Extra optical zoom" <Control No.: C0124>
"How to take a wide depth of field" <Control No.: C0127>

When using "Image rotation" Rotate the sunshade
Technical information website "Installation method for rotating the sunshade" <Control No.: C0131>

References

Adobe PDF Library 17.0

	i-PRO Network Camera Installation Guide: WV-S2231L, WV-S2211L, WV-S2131 Series Comprehensive installation guide for i-PRO network cameras including models WV-S2231L, WV-S2211L, WV-S2131L, WV-S2131LRF, WV-S2131LEG, WV-S2131, WV-S2130, WV-S2111L, and WV-S2110. Learn how to mount, connect, and configure your camera.
	i-PRO Partner EC Purchase Guide: Step-by-Step Instructions A comprehensive guide detailing the i-PRO Partner EC site purchase procedure, from login and product selection to payment and delivery. Learn how to navigate the partner portal and efficiently order i-PRO products and licenses.
	i-PRO パートナーEC購入ガイド：ステップバイステップ手順 i-PROパートナーがi-PROパートナーECサイトを利用して商品を購入するための詳細ガイド。ログイン、商品選択、注文、支払い、ユーザー管理方法を解説。
	i-PRO USB Type-C 電源に関するお知らせ i-PRO製カメラ製品（i-PRO Mini, i-PRO Mini L, スピーカーカメラ）のUSB Type-C電源アダプタおよびケーブルの使用に関する重要なお知らせと推奨事項。
	i-PRO WV-U21300-V2L 2MP 屋内ドームネットワークカメラ \| 特長・仕様 i-PRO WV-U21300-V2Lは、2MP (1080p) 解像度、光学2.5倍ズーム、内蔵マイクを備えたエントリーモデルの屋内用ネットワークカメラです。高画質ストリーム、スマートコーディング、インテリジェントオート機能などを搭載し、様々な環境で優れた視認性を発揮します。
	i-PRO WV-CF5SA Dome Cover Operating Instructions Detailed operating and installation instructions for the i-PRO WV-CF5SA Dome Cover, compatible with various i-PRO camera models like WV-SFN631L, WV-SFN611L, WV-SF538, and WV-SF539. Includes precautions, mounting steps, and specifications.
	WV-S6530N 2MP PTZ Network Camera: Features, Specifications, and Applications Detailed overview of the i-PRO WV-S6530N 2MP (1080p) PTZ Network Camera, highlighting its extreme image quality, bandwidth compression with H.265 Smart Coding, and advanced data security features. Includes specifications, bundled licenses, optional accessories, and industry applications.
	i-PRO Network Camera Installation Guide: WV-S3531L, WV-S3511L, WV-S3131L, WV-S3111L, WV-S3532LM, WV-S3512LM This installation guide provides detailed instructions for setting up i-PRO network cameras, including models WV-S3531L, WV-S3511L, WV-S3131L, WV-S3111L, WV-S3532LM, and WV-S3512LM. It covers essential safety precautions, mounting procedures, cable connections, network configuration, camera adjustment, and enclosure attachment, ensuring proper installation and operation.

References

Related Documents