Arboleaf Smart Body Tape Measure
Quick Start Guide
Model: CF10A
Thank You
Thank you for choosing the Arboleaf Smart Body Tape Measure!
Warranty
Your Arboleaf Smart Body Tape Measure is covered by a one-year warranty from the date of purchase, safeguarding against defects. Proof of purchase is required.
Customer Support
1-800-658-1148 (US)
support@arboleaf.com (US)
support.eu@arboleaf.com (EU)
Arboleaf Corporation
5465 Legacy Drive, Suite 650
Plano, TX 75024, USA
Precautions
- Do not use the tape measure for any unintended purposes.
- Do not attempt to disassemble or modify the device.
- Exercise caution when measuring neck circumference. Avoid retracting the tape too rapidly to prevent discomfort or choking risks.
- Ensure that children use the device under the supervision of an adult.
Package Contents
- 1 x Smart Body Tape Measure
- 1 x CR2032 Battery
- 1 x User Guide
Product Overview
The Arboleaf Smart Body Tape Measure is a compact device designed for accurate body measurements. It features a digital display, a retractable tape, and control buttons.
Device Components:
- Retract Button: Used to retract the tape measure.
- Lock Pin: Secures the tape end.
- Unlock Button: Releases the tape.
- Power Button: Press to turn on; hold for 2 seconds to turn off.
- M Button: Press briefly for measurement; hold for 2 seconds to switch units (e.g., cm/in).
- Battery Compartment: Located on the back, houses the CR2032 battery.
Quick Start Guide
1. Power Up the Smart Tape Measure
- Open the rear battery cover.
- Insert the provided CR2032 coin battery securely and evenly into the battery compartment.
- Close the cover.
2. Initial Setup with the Arboleaf App
2.1 Download the Arboleaf App
Search for "Arboleaf" on the Apple App Store or Google Play Store. Alternatively, scan the QR code provided in the original document to download the app. Verify the app's authenticity before downloading.
2.2 Sign Up
Open the app, allow Bluetooth permission, and enable Location service (on Android phones). Sign up using your email and complete your profile information.
2.3 Pair Your Device
Ensure Bluetooth is enabled on your phone and Location service is enabled (on Android phones). Press the Power Button on the tape measure to turn it on. In the Arboleaf app, navigate to 'Device' > '+ Add device' > 'Smart Tape Measure'. Select your tape model and tap 'Connect'. Finally, press 'Finish'. Your smart tape measure is now successfully connected.
3. Take Measurements
Turn on the tape measure. Log into the Arboleaf app. On the Home screen, scroll down to the 'Body Measurements' section and tap anywhere within it. Tap 'Record' to go to the 'Body Measurements' screen. Choose the specific body part you wish to measure (e.g., waist, hip, arm). Gently pull out the tape and wrap it around the designated body area. Insert the Lock Pin securely into the tape receptacle. Press the Retract Button to fine-tune the tape length, and then press the M Button to save the measurement.
Specifications
| Specification | Value |
|---|---|
| Model | CF10A |
| Unit | in/cm |
| Resolution | 1/16 in / 1 mm |
| Precision | 2% |
| Maximum Tape Length | 60 in / 1.5 m |
| Battery | CR2032 |
| Working Temperature | 32°F ~ 122°F / 0°C ~ 50°C |
| Working Humidity | <85% |
Troubleshooting Guide
| Problem | Potential Cause | Solution |
|---|---|---|
| No display, blurred display, or flashing numbers | No battery, weak battery, battery installed incorrectly | Reinstall or replace battery |
| Frozen display | Internal error | Remove the battery, wait for one minute, and reinstall the battery |
| The display fails to reset to zero after the tape retracted to zero position | Internal error | Press the Power Button and M Button simultaneously |
| Display becomes 0 while connecting to Bluetooth | Low battery | Replace the battery |
| Unable to connect to the app | Low battery or other issues | Replace the battery, or refer to step 2.3 to reconnect the tape measure. |
WARNING
INGESTION HAZARD: This product contains a button cell or coin battery.
DEATH or serious injury can occur if ingested.
A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
KEEP new and used batteries OUT OF REACH of CHILDREN.
Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Company Information
UK Representative: YH Consulting Limited, Address: C/O YH Consulting Limited Office, 147 Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX, Telephones: +44 07514-677868, Mail: H2YHUK@gmail.com
EU Representative: E - CrossStu - GmbH, Mainzer Landstr. 69, 60329 Frankfurt am Main, Mail: E-CrossStu@web.de
Manufacturer: Shenzhen Yolanda Technology Co., Ltd., Room 201, Jinfulai Building, No.49-1, Dabao Road, Dalang Area, Xinan Street, Baoan, Shenzhen, China. Service: service@yolanda.hk, Phone: 400-998-2913
Arboleaf Corporation (also listed with US address)
Safety and Disposal
Please do not dispose of used batteries in household waste. You are legally required to recycle used batteries. Dispose of batteries at designated collection points in your area to protect the environment and human health.
Compliance Marks:
The device complies with various standards and regulations, indicated by the following marks:
- PSE mark (Japan)
- R 217-220522 (Korea)
- FCC (USA)
- UKCA (United Kingdom)
- CE (Europe)
- RoHS (Restriction of Hazardous Substances)
- WEEE symbol (Waste Electrical and Electronic Equipment)
