Whirlpool AWE 2316 Toploader Washing Machine Service Information

Model: AWE 2316

Document Reference: 8593 231 10060

Last Modification: 01/30/09

Spare Part List

Pos No	12NC	Description
002 0	4812 459 38057	Flap round GW
002 1	4812 459 38058	Hinge flap GW
004 0	4812 440 19625	Drip tray assy
010 0	4812 459 48175	Door frame inner GW
010 1	4812 440 11637	Frame Top+nozzle box KIT
011 0	4812 462 48054	Foot
012 7	4812 310 18497	Trolley kit front
012 8	4812 528 78075	Foot rear
021 0	4812 440 10838	Front panel WH GW
022 0	4812 440 10839	Side panel right GW
022 1	4812 440 10841	Side panel left GW
024 0	4812 440 11638	Rear panel
040 0	4812 417 19155	Hinge bolt lid GW
061 0	4812 466 88489	Counter weight
061 1	4812 466 88491	Counter weight front
061 2	4812 466 88492	Counter weight bottom
081 4	4812 529 18043	Shock absorber
086 4	4812 529 18045	Pin f. Shock absorber
086 5	4812 529 18052	Damper f. Shock absorber
100 1	4812 440 10842	Lid outer GW
100 3	4812 440 10843	Lid inner GW
100 5	4812 440 10845	Lid assembly WH GW
110 4	4812 498 18249	Handle cpl. WH GW
130 0	4812 417 19193	Door latch GW
191 0	4812 466 68596	Door bellow
191 1	4812 492 98037	Strap f. bellow
200 0	4812 418 18242	Tub 4 fix points
201 0	4812 440 19644	Cover cpl.
220 0	4812 418 18556	Drum soft op., to 800
223 0	4812 418 48725	Drum lifter
271 0	4812 358 18167	Belt Poly V 1204 H8 MA
272 0	4812 528 88083	Pulley 298 mm
290 0	4812 532 68078	Gasket
301 0	4812 452 17723	Control panel AWE 2316
331 0	4812 414 58306	Knob timer EBL WP25
331 2	4812 414 58307	Spring Knob timer
333 0	4812 410 29503	Push button start/reset
333 1	4812 410 29504	Push button option
400 0	4812 361 58444	Motor 1BA5736-0WA/BSH
421 0	4812 121 18285	Interf.filter 1,00 μF
421 2	4812 404 38679	Holder RFI
430 0	4812 360 18577	Pump,draining
451 0	4812 259 28919	Heating element 2050W, 230V + NTC
490 0	4819 321 18136	Cable mains 2m SA
490 1	4812 321 28367	Strain relief
521 0	4812 214 70161	Control unit DOMINO, programmed
521 0	4812 214 70092	Control unit DOMINO, basic C1
571 0	4812 281 28468	Valve magnet 1 inlet, 2 outlets
571 1	4812 281 18069	Cover for top frame
581 0	4812 271 28585	Pressostat 50/25 INVENS.
630 0	4812 271 38519	Door lock 3P ROLD
653 0	4812 134 18077	Light guide PR.FLOW-FULL
691 0	4812 282 19485	Sensor NTC SC1,OMEGA3,DOMINO
701 0	4812 530 29329	Hose inlet EN 11770 Reflex
702 2	4812 530 29453	Hose valve-dispenser
707 0	4812 526 48242	Nozzle box cold cpl.
707 1	4812 526 48049	Clamp f. nozzle box
712 4	4812 418 68302	Siphon f. softener
712 6	4812 418 68164	Clip soap dispenser
712 9	4812 418 68404	Soap dispenser cpl. 3 ch.
753 0	4812 418 68187	Chamber,air
754 0	4812 530 28938	Drainhose
754 1	4812 530 28832	Lock eco
760 0	4812 480 58089	Filter set pump
781 0	4819 530 29035	Hose draining
782 0	4812 530 28941	Hose Pressostat
787 0	4812 530 29309	Hose Air Exaust
787 1	4812 530 29311	Cover of hose
794 0	4812 530 58098	Gasket airtrap
900 0	4819 401 18686	Clamp hose
900 1	4812 401 18431	Clamp to pump
900 2	4812 255 18304	Holder hose
900 3	4819 401 18529	Clamp hose
901 0	4812 401 18462	Clamp hose drain hose
910 0	4812 502 48347	Screw,selftap 3,5x14SS
910 1	4812 502 38151	Screw 4x14
910 3	4812 502 18404	Screw
910 4	4812 502 18423	Screw PT 7x15
910 5	4812 502 18705	Screw M8x35
910 6	4812 502 18399	Nut Push in M 8
921 0	4812 400 18047	Washer
930 1	4812 492 48171	Torsions spring
930 2	4812 492 48162	Spring
941 0	4812 310 18578	Bearing Kit
953 0	4812 325 68001	Shaft seal
962 0	4812 440 98142	Cover for Motor AC
962 2	4812 440 11424	Spacer
965 0	4812 462 79974	Cap Transport blocking
990 0	4812 310 18504	Fixing mat.set front counter
990 2	4812 310 18506	Fixing mat.set bottom
993 0	4819 530 29028	Bow
993 1	4812 290 18025	Clamp heatingelement

Technical Data

Dimensions & Weight

Product dimensions:

Height: 85 cm
Width: 40 cm
Depth: 60 cm

Weight:

Gross: ~66 kg
Net: ~63 kg

Electrical Base Data

Voltage: 230-240 V ± 10%
Frequency: 50 Hz
Fuse: 10 A
Power Consumption: ~2.3 kW

Drum Data

Volume: 42 l
Wash speed: 52 rpm
Spinning speed max.: 800 rpm

Capacity of Dry Laundry

Cotton (95°C-60°C-40°C): 5.0 kg

Synthetics (60°C/40°C/30°C): 2.5 kg

Program Specific Capacities:

Delicate (40°C/30°C): 1.5 kg
Chrono (40°C): 3.0 kg
Quick Wash (30°C): 3.0 kg
Wool: 1.0 kg
Handwash (40°C/30°C): 1.0 kg
Rinse & Spin: 5.0 kg
Spin: 5.0 kg
Gentle Spin: 1.0 kg
Jeans: 5.0 kg

Pressostat

Type: B1 - 250
Nominal voltage: 230 V
Water Level: Level1
Switching point: 50 ± 5 mmWc
Switching back point: 25 ± 5 mmWc
Overflow: 300 ± 20 mmWc

Door Lock

Type: BP P/5 DA
Kind of switch: Switch with PTC heater of bimetal
Locking time max.: 6"
Unlock time: 37-65"
Nominal voltage: 230 (90 - 264) V
Nominal current: 16 (6) A
Contact: 4 - 5 (250 V)

Heating Element

Kind of heating: Tubular heating element with NTC sensor
Nominal voltage: 230 +10%, -15% V
Total power: 2050 W ± 5%
Resistance (20°C): 23.9 Ω ± 5%
Thermo-fuse (switch OFF temperature): 152 °C
Leakage current: <0.8 mA

NTC Sensor Resistance

Temperature	Resistance
0 °C	35.9 kΩ ±5.8%
30 °C	9.8 kΩ ±3.7%
40 °C	6.6 kΩ ±3.1%
50 °C	4.6 kΩ ±2.6%
60 °C	3.2 kΩ ±2.0%
70 °C	2.3 kΩ ±2.5%
95 °C	1.1 kΩ ±3.7%

Electronic

Type: DOMINO
Basic: 4619 714 03655

Programs Overview

The machine offers a variety of wash programs, including:

Cotton 95°C, Cotton 60°C, Cotton 40°C
Synthetics 60°C, Synthetics 40°C, Synthetics 30°C
Delicate 40°C, Delicate 30°C
Daily 40°
Quick wash
Wool 40°C, Wool cold
Handwash 40°C, Handwash 30°C
Rinse & Spin
Spin
Gentle Spin
Spin Drain

Programmed: 4619 751 56591

Nominal voltage: 220 V - 240 V

Frequency: 50 - 60 Hz

Ambient temperature: 0 to 70°C

Storage temperature: -35 to 70°C

Output Control Unit

Component	Type/Model	Voltage
Motor	M7.6 - DSS3.2	>40 V
Aquastop	AQ2.2 - DSS3.2	230 V
in pump step	AQ2.1 - DSS3.2	230 V
NTC	not measurable
Pump	DP2.1 - DP2.2	230 V
Doorlock	DSS3.1 - DSS3.3	230 V
Pressostat	E4 - E2	230 V
- empty	PR2.1 - E2	230 V
- full	PR2.2 - E2	230 V
Valve (Rast 2.5)	V2.1 - V2.2	>170 V
Options	not measurable

Inlet Valve

Type: 1-way valve for cold water
Water temperature: 5 - 90°C
Rated flow: 8 l/min ± 8% (1 - 1.5 bar)
Pressure range: 0.3 bar - 10 bar
Nominal voltage: 220 V - 240 V
Frequency: 50 Hz
Nominal current: 35 mA
Nominal resistance: 3.8 kΩ ± 10% (20°C)
Total power: 6 W ± 10%

Drain Pump

Type: 292079 (synchronous)
Nominal voltage: 220 V - 240 V
Nominal current: 0.2/0.22 A
Total power: 26 W
Rotations: 3000 rpm
Frequency: 50 Hz
Resistor (coil): 224 Ω ± 5%
Motor protection: no
Capacity: 14 ± 2 l/min
Position of draining hose outlet: 0.9 m - 1.25 m

Motor

Type: 1BA5736-OWA
Belt ratio: i = 1:20.0
Resistance contacts (20°C)
Stator (full field): 1.95 Ω ± 7%
Rotor: 1.85 Ω ± 7%
Tacho generator: 13.3 Ω ± 7%

Input power:

Washing (230 V AC): 130 W ± 7%
Rinsing: 246 W ± 7%
Spinning: 340 W ± 10%

Radio Interference Filter

Rated voltage: 90 - 250 V
Rated current: 16 A
Frequency: 50/60 Hz
Nominal capacity: 240/250 nF X1 + 2 x 22 nF Y ± 20%
Nominal resistance: 1000 KΩ ± 5%
Derivation current (u = 250 V AC): < 4.15 (2 x 2.075) mA

Push Button Switch

Start
Reset
Switch Rinse intensive
Switch no spin

Exploded View

The exploded view diagrams illustrate the physical assembly of the Whirlpool AWE 2316 washing machine, showing how various components are interconnected and mounted. Key components visible include the outer casing (front, side, rear panels, top frame), door assembly (frame, lid, hinges, latch), internal drum assembly (tub, drum lifters, shock absorbers), motor and drive system, water inlet and drainage components (valve, hoses, pump, filter), and control/user interface elements (control unit, knobs, buttons, display). Specific part numbers are referenced in the Spare Part List for detailed identification.

Wiring Diagram

The wiring diagram provides a schematic representation of the electrical connections within the washing machine. It details the routing of wires between the main control unit (CUC), various input components (sensors, switches), and output components (motor, pump, heating element, valves). The diagram uses standard electrical symbols and indicates wire colors and terminal connections for troubleshooting and repair. Key connections shown include the control unit (CUC) to motor (M7.6), pump (DP2.1, DP2.2), heating element (HE), door lock, and pressostat (PR), as well as NTC sensor connections and connections for push buttons and program selection. Terminal blocks (MX12.1, MX12.12) are shown for main power and component interfaces.

Circuit Diagram

The circuit diagram illustrates the functional logic of the washing machine's electrical system, showing how components interact and how signals are processed by the control unit (CUC). The diagram depicts power supply lines (L1, N), switching elements, relays, and the flow of control signals for different wash phases and functions. It outlines the operation of the CUC in managing wash cycles, temperature control, motor speed, and water levels, as well as the function of the pressostat for water levels, the NTC sensor for temperature, and the operation of the door lock, pump, and heating element, including connections to program selection and option switches.

Program Charts

The program charts detail the sequence of operations, timing, water temperatures, and drum speeds for various wash cycles. Each chart outlines the different wash phases, including prewash, main wash, rinses, and spin cycles, along with specific settings and options. Key programs covered include Cotton (95°C, 60°C, 40°C), Synthetics (60°C, 40°C, 30°C), Delicate (40°C, 30°C), Daily 40°, Quick wash, Wool (40°C, cold), Handwash (40°C, 30°C), Rinse & Spin, Spin, Gentle Spin, and Spin Drain. Spinning profiles (ES1, ES2, ES3, ES4) are also provided, illustrating the drum speed progression during spin cycles.

Text Legend and Failure Indications

Test Program Flow

Instructions for initiating a test program are provided, typically involving switching on the appliance, selecting the DRAIN program, and pressing the Reset button multiple times. This program is intended for use without laundry.

LED Status and Program Flow:

Digits	Description of Program Flow	Check to Perform
0	The door is locked. The CUC is performing the Selftest. Fill 15" hot valve (only if hot fill appliance). Fill 15" in prewash (PW).	CUC detects F05, F08, F12, F13, F14, F15, F23. Technician: Check the valve activation, Check the dispensing into the dispenser.
1	Fill 15" in prewash (PW). Fill 15" in mainwash (MW). Fill 15" in PW + MW (Softener). Fill by MW to wash level.	Technician: Check heating element activation, Check if the motor is reversing.
2	Motor is reversing. The heating element is switched ON. Motor is reversing.	CUC detects: F06, F07, F27. Technician: Check heating element activation, Check if the motor is reversing.
3	The drain pump is switched ON until the wash level = OFF + 5" motor is reversing.	CUC detects: F06, F07, F27. Technician: Check drain pump activation, Check pressure switch operation, Check if the motor is reversing.
4	The motor is driven to maximum speed. Drain pump is ON.	CUC detects: F28. Technician: Check if the motor is running at max. speed, Check drain pump activation.
5	Motor is switched OFF. Door is unlocked.	CUC detects: F13. Technician: Check if the door is unlocked.

* Digits 1, 2 (the left ones) are executing an animation.

Failure Indications and Recommended Procedures

Failure Indication	On Digits / On Status LEDs (if available)	Explanation and Recommended Procedure
No water detected entering machine or pressure switch trip not detected.	FA	If after 6 minutes the control does not detect water entering machine, valves are turned off and the LED Water Tap is switched ON. The Control is in Pause Mode. If the failure is removed, pushing PB Start will restart the appliance. Potential Causes: No water in the unit: Ensure valves are on, check inlet hoses/screens, verify inlet valve operation. Water in the unit: Check pressure switch hose, verify no siphon problem, check wire harness connections to valves, pressure switch, CUC; check hoses for leaks; verify pressure switch and CUC operation.
Long Drain		If drain time exceeds 8 minutes, LED clean Filter is turned ON. Control is in Pause Mode. Restart by pushing PB Start if failure is removed. Potential Causes: Check drain hose for blockage/kinks. Check electrical connections at the pump, ensure pump is running. Check drain pump filter for foreign objects. Check electrical resistance of the drain pump.
Aquastop Failure		Aquastop contact on the bottom tray closed for >30". Door remains locked, drain pump runs constantly. Potential Causes: Water in bottom tray: Check hoses for leakage, check for overfoam, check tub for leakage. No water in bottom tray: Check aquastop switch for short circuit, check aquastop wiring, verify CUC operation.
Too Long Heat Time	F04	Water temperature not increasing over 35°C during 40 minutes of the first heating step. Potential Causes: Check electrical resistance of the heating element. Check wire harness connections to heating element, NTC, and CUC. Check electrical resistance of the NTC.
Water Temperature Sensor Error	F05	NTC sensor value out of range during water heating. Potential Causes: Check the NTC resistance. Check connections to the NTC and CUC.
Drive Motor Tachometer Error	F06	Control unable to properly detect motor speed. Machine shuts down. Door unlocks after drum stops. Potential Causes: Check wire harness connections between motor and CUC. Check tachometer circuit resistance on motor. Check motor windings resistance.
Motor Control Triac Error	F07	Main control detected a short circuit in the motor control triac. Door unlocks after drum stops. Potential Causes: Check CUC by running Test Program.
Heater Circuit Error	F08	Main control detected a heater circuit failure. Checked before cycle start and after spinning. Potential Causes: Check heater connectors resistance to ground. Check heater resistance. Check wiring connectors to heater and CUC. Check the CUC.
Door Open LED flashing after cycle start	F12	CUC cannot lock the door within 10" after program start. Door open LED flashes for 10". Potential Causes: Check if door is closed properly. Check for mechanical problem on door lock system. Check wiring/harness between CUC and door lock. Start Test Program. If problem persists, error Code F13 will be displayed.
EEPROM Error	F13	Error reading EEPROM data on CUC. Potential Causes: Power glitch may cause this error. Run Test Program for complete EEPROM check. If failure detected, replace CUC.
Drum Up Circuit Missing	F14	CUC not detecting Drum Up switch closing during motor rotation (only for TOPLOADERS with DRUM UP Circuit). Detected ONLY during Test Program. Potential Causes: Check position of electromagnetic device. Check position of reed sensors. Check resistance of reed sensor. Check wiring connection between reed sensor and CUC.
User Interface Error	F15	Communication between user interface module and CUC is disturbed. Potential Causes: Check wiring connection to the display module. Check display module. Check CUC.
Pressure switch Failure	F21, F23	CUC detects pressure switch contacts for wash level and heater safety ON simultaneously for 10". Potential Causes: Check resistance of pressure switch contacts. Check wiring to pressure switch and CUC. Start Test Program. If problem persists, F23 will be displayed.
Overflow Failure	F24	Overflow contact on pressure switch closed for >60". Door locked, drain pump runs constantly. Potential Causes: Check drain hose for blockage/kinks. Check wire harness connections to drain pump, pressure switch, CUC. Check/clean drain pump filter. Check for drain pump failure. Check inlet valve for proper shut off. Check pressure switch for proper operation.
Pump Driver Failure	F26	CUC detects defective pump triac during wash cycle. Potential Causes: Check resistance of pressure switch contacts. A failure of the pressure switch could also cause the Code. If OK, start Service test to check CUC. If failure occurs, replace CUC.
Reversing relay failure	F27	CUC detects motor can only rotate in one direction. Potential Causes: Check harness to the motor. Check the CUC.
Tapped Field Failure	F28	CUC cannot switch ON the tapped field of the Motor. Potential Causes: Check if correct motor is built in. Check resistance of motor fields. Check harness between Motor and CUC. If points above are OK, replace CUC.
Foam detected During the Wash Cycle	Fod	CUC unable to drain water after washing or spin after several trials. Potential Causes: Customer used too much detergent. Check pump hoses for issues. Check electrical resistance of the pump. Check electrical resistance of the pressure switch. Check pressure switch hose condition and connection. Verify no siphon problem.

	Whirlpool Microwave Oven Exploded Parts Diagram and Service Information Provides a detailed exploded view diagram of a Whirlpool microwave oven, listing all components with their alphanumeric identifiers for service and identification purposes. Includes overview of major assemblies and a comprehensive component list.
	Whirlpool S20B RSB21-A/G Side by Side Refrigerator Service Manual This service manual provides detailed technical specifications, a comprehensive spare parts list, exploded views, and circuit diagrams for the Whirlpool S20B RSB21-A/G Side by Side refrigerator. It is intended for qualified technicians.
	Whirlpool AVM541WH Microwave Oven Exploded Parts Diagram Detailed exploded view diagram of the Whirlpool AVM541WH microwave oven, illustrating the assembly of its various components with numerical references for each part.
	Whirlpool Microwave Oven Parts Diagram - Model 4000 107 85476 Exploded view diagram detailing replacement parts for a Whirlpool microwave oven, including reference numbers for components like the cavity, control panel, magnetron, and various external panels.
	Whirlpool AMW521 Microwave Oven Exploded View Parts Diagram Detailed exploded view parts diagram for the Whirlpool AMW521 microwave oven, listing all components and their corresponding part numbers for easy identification and replacement.
	Whirlpool AMW466NB Microwave Oven Parts Diagram Exploded view diagram and parts list for the Whirlpool AMW466NB microwave oven, detailing internal and external components for identification and service.
	Whirlpool WRX38RWH6 WRX42RWH6 Top Mount Refrigerator Service Manual This service manual provides detailed technical information for Whirlpool WRX38RWH6 and WRX42RWH6 top mount refrigerators, covering product specifications, electrical data, circuit diagrams, servicing procedures, and comprehensive parts lists for all compartments and doors.
	Whirlpool MWD270SL Microwave Parts Diagram Exploded view parts diagram for the Whirlpool MWD270SL microwave, detailing all components and their reference numbers for replacement and service.