Infinix X6835 User Manual
This document provides information for the Infinix X6835 smartphone.
Explosion Diagram Specification
The following table details the components of the Infinix X6835 as shown in the explosion diagram:
| Part Number | Description | Part Number | Description |
|---|---|---|---|
| 1 | FL(CTP+LCM) | 2 | F HSG ASM |
| 3 | PS RUBBER | 4 | PCBA COPPER C |
| 5 | PCBA COPPER A | 6 | PCBA COPPER B |
| 7 | PCBA MB | 8 | PCBA GRAPHITE FILM |
| 9 | F CAM FRAME | 10 | F CAM |
| 11 | FPC SIDE KEY | 12 | F CAM COPPER |
| 13 | REC | 14 | REC COPPER |
| 15 | FM | 16 | CARD HOLDER |
| 17 | R CAM CON FOAM 16M | 18 | R CAM 16M |
| 19 | R CAM CON FABRIC 8W | 20 | R CAM 8W |
| 21 | LCM CONN RUBBER | 22 | BAT CONN RUBBER |
| 23 | MAIN WATERPROOF FRAME | 24 | MAIN WATERPROOF MYLAR |
| 25 | MI HOUSING | 26 | MI RAD GRA |
| 27 | 28 | SCREW L3.5 | |
| 29 | R FLASH DECO | 30 | R CAM DECO 16M |
| 31 | R CAM RUBBER 8W | 32 | BAT COVER ASM |
| 33 | R FLASH LENS | 34 | R CAM LENS 16M |
| 35 | R CAM LENS 8W | 36 | R CAM DECO 8W |
| 37 | SCREW L2.0 | 38 | SUB CONN RUBBER |
| 39 | SPK | 40 | MOTOR LINEA |
| 41 | PCBA SUB | 42 | USB RUBBER |
| 43 | EARPHONE RUBBER | 44 | BAT |
| 45 | COAXIAL CABLE |
Know Your Phone
The Infinix X6835 features the following external components:
- 1. Front camera
- 2. Volume + key
- 3. Volume - key
- 4. Power key & side fingerprint sensor
SIM/SD Card Installation
To install the SIM or SD card:
- Power off the mobile device.
- Refer to the provided illustration for correct SIM/SD card placement.
[Illustration of SIM/SD card installation]
Charging the Phone
The device can be charged using a charger or by connecting it to a computer via a USB cable.
It is recommended to use only Infinix-branded chargers and cables to avoid device damage and warranty invalidation.
[Illustration showing phone charging via USB]
FCC Caution
Labelling requirements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference.
- (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to user:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Information to the user:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: X6835 (FCC ID:2AIZN-X6835) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.11W/kg and when properly worn on the body is 1.24W/kg.
Body-worn Operation:
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
DTS Information
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
[DTS Logo]
System Information
Operating System: Android™
Android is a trademark of Google LLC.
