Manuals+

Teltonika RUT360

Brand: Teltonika Networks

The Teltonika RUT360 is an industrial LTE Cat6 router designed for robust connectivity in demanding environments.

Hardware Overview

Front View

The front panel features:

  • Mobile network type LEDs
  • Mobile signal strength indication LEDs
  • Power socket
  • Power LED
  • SIM holder
  • LAN Ethernet port
  • WAN Ethernet port
  • ETH activity LEDs

Back View

The back panel features:

  • WiFi antenna connector
  • Mobile MAIN antenna connector
  • Mobile AUX antenna connector
  • Reset button

Power Socket Pinout

The 4-pin industrial DC power socket has the following pinout:

  • Power / Red wire
  • Input/Output / Green wire
  • Ground / Black wire
  • Input/Output / White wire

Note: I/O pins are programmable digital inputs/outputs (Open Collector output max 30 V, 300 mA or Digital input where 0-6 V is detected as logic low and 8-30 V as logic high).

Features

Mobile

FeatureSpecification
Mobile module4G (LTE) - Cat 6 up to 300 Mbps, 3G - Up to 42 Mbps
StatusSignal strength, SINR, RSRP, RSRQ, Bytes sent/received, connected band, carrier aggregation, IMSI, ICCID
SMSSMS status, SMS configuration, send/read SMS via HTTP POST/GET, Email to SMS, SMS to Email, SMS to HTTP, SMS to SMS, SMS auto reply
USSDSupports sending and reading Unstructured Supplementary Service Data messages
Black/Whites list (planned)Operator black/white list
Multiple PDNPossibility to use different PDNs for multiple network access and services
Band managementBand lock, Used band status display
APNAuto APN
Bridge modeDirect connection (bridge) between mobile ISP and device on LAN

Wireless

FeatureSpecification
Wireless mode802.11 b/g/n, 2x2 MIMO, Access Point (AP), Station (STA)
WiFi securityWPA3-EAP, WPA3-SAE, WPA2-Enterprise-PEAP, WPA2-PSK, WEP; AES-CCMP, TKIP, Auto Cipher modes, client separation
ESSIDESSID stealth mode
Wireless HotspotCaptive portal (Hotspot), internal/external Radius server, SMS OTP, MAC auth, built-in customizable landing page, walled garden

Ethernet

FeatureSpecification
WAN1 x WAN port (can be configured as LAN) 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover
LAN1 x LAN port, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover

Network

FeatureSpecification
RoutingStatic routes, Dynamic routes (planned)
VoIP passthrough supportH.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
Network protocolsTCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP (planned), SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet client, SNMP (planned), MQTT (planned), Wake on LAN (WOL) (planned)
Connection monitoringPing Reboot, Wget reboot, Periodic Reboot, LCP and ICMP for link inspection
FirewallPort forwards, traffic rules, NAT rules, custom rules
DHCPStatic and dynamic IP allocation, DHCP Relay, Relayd
QoS / Smart Queue Management (SQM) (planned)Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
DDNS (planned)Supported >25 service providers, others can be configured manually
Network backupMobile, Wired and WiFi WAN options, each of which can be used as an automatic Failover
Load balancingBalance Internet traffic over multiple WAN connections
SSHFS (optional)Possibility to mount remote file system via SSH protocol (not available in standard FW)

Security

FeatureSpecification
AuthenticationPre-shared key, digital certificates, X.509 certificates
FirewallPre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
Attack preventionDDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)
VLANTag based VLAN separation
Mobile quota controlCustom data limits for both SIM cards
WEB filter (planned)Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only
Access controlFlexible access control of TCP, UDP, ICMP packets, MAC address filter

VPN

FeatureSpecification
OpenVPNMultiple clients and a server can run simultaneously, 12 encryption methods
OpenVPN EncryptionDES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC
IPSecIKEv1, IKEv2, with 5 encryption methods for IPsec (DES, 3DES, AES128, AES192, AES256)
GREGRE tunnel
PPTP, L2TPClient/Server instances can run simultaneously, L2TPv3 support (planned)
Stunnel (planned)Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program's code
DMVPN (planned)Method of building scalable IPsec VPNs
SSTP (planned)SSTP client instance support
ZeroTierZeroTier VPN client support
WireGuardWireGuard VPN client and server support

MODBUS TCP SLAVE (PLANNED)

FeatureSpecification
ID filteringRespond to one ID in range [1;255] or any
Allow remote accessAllow access through WAN
Custom registersModbus TCP custom register block, which allows to read/write to a file inside the router, and can be used to extend Modbus TCP slave functionality

MODBUS TCP MASTER (PLANNED)

FeatureSpecification
Supported functions01, 02, 03, 04, 05, 06, 15, 16
Supported data formats8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

MQTT GATEWAY (PLANNED)

FeatureSpecification
GatewayAllows sending commands and receiving data from Modbus Master trough MQTT broker

DATA TO SERVER (PLANNED)

FeatureSpecification
ProtocolsHTTP(S), MQTT, Azure MQTT, Kinesis

Monitoring & Management

FeatureSpecification
WEB UIHTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log
FOTAFirmware update from server, automatic notification
SSHSSH (v1, v2)
SMSSMS status, SMS configuration, send/read SMS via HTTP POST/GET
CALLReboot, Status, Mobile data on/off, Output on/off
MQTT (planned)MQTT Broker, MQTT publisher
SNMP (planned)SNMP (v1, v2, v3), SNMP trap
JSON-RPCManagement API over HTTP/HTTPS
Modbus (planned)Modbus TCP status/control
RMSTeltonika Remote Management System (RMS)

IoT Platforms

PlatformDescription
Clouds of thingsAllows monitoring of: Device data, Mobile data, Network info, Availability
ThingWorxAllows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type
CumulocityAllows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IP
Azure IoT HubCan send device IP, Number of bytes send/received, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server

System Characteristics

FeatureSpecification
CPUQCA9531, MIPS 24kc, 650 MHz
RAM128 MB, DDR2
FLASH storage16 MB, SPI Flash

Firmware / Configuration

FeatureSpecification
WEB UIUpdate FW from file, check FW on server, configuration profiles, configuration backup
FOTAUpdate FW/configuration from server
RMSUpdate FW/configuration for multiple devices at once
Keep settingsUpdate FW without losing current configuration

Input/Output

FeatureSpecification
Configurable I/O2 x Configurable digital Inputs/Outputs. Digital input 0 - 6 V detected as logic low, 8 - 30 V detected as logic high. Open collector output, max output 30 V, 300 mA
EventsSMS, Email, RMS

Power

FeatureSpecification
Connector4 pin industrial DC power socket
Input voltage range9 - 30 VDC, reverse polarity protection, voltage surge/transient protection
Power consumption10.5 W max

Physical Interfaces

InterfaceSpecification
Ethernet2 x RJ45 ports, 10/100 Mbps
I/Os2 x Configurable digital Inputs/Outputs on 4 pin power connector
Status LEDs2 x Mobile connection type, 3 x Mobile connection strength, 2 x Eth status, 1 x Power
SIM1 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V, external SIM holders
Antenna2 x SMA for LTE, 2 x RP-SMA for WiFi
Power1 x 4 pin DC connector
ResetReboot/User default reset/Factory reset button

Physical Specification

ParameterSpecification
Casing materialAluminium housing with DIN rail mounting option
Dimensions (W x H x D)100 x 30 x 85 mm
Weight247 g
Mounting optionsDIN rail, flat surface placement

Operating Environment

ParameterSpecification
Operating temperature-40 C to 75 C
Operating humidity10% to 90% non-condensing

Hardware Installation

  1. Push the SIM button with the SIM needle.
  2. Pull out the SIM holder.
  3. Insert your SIM card into the SIM holder.
  4. Slide the SIM holder back into the router.
  5. Attach Mobile and WiFi antennas.
  6. Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.
  7. Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to LAN port.

Login to Device

  1. To enter the router's Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
  2. Use login information shown in image A when prompted for authentication.
  3. After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter, and one digit. This step is mandatory, and you will not be able to interact with the router's WebUI before you change the password.
  4. When you change the router's password, the Configuration Wizard will start. The Configuration Wizard is a tool used to set up some of the router's main operating parameters.
  5. Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

Image A shows the authorization screen with fields for username and password. Image B shows signal strength indicators.

Technical Information

Radio Specifications

FeatureSpecification
RF technologies3G, 4G, WiFi
Max RF power24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi

Bundled Accessories Specifications

ItemSpecification
Power adapterInput: 0.6 A@100-240 VAC, Output: 12 VDC, 1.5 A, 4 pin plug
Mobile antenna698~960/1710~2690 MHz, 50 Ω, VSWR<3, gain** 4 dBi, omnidirectional, SMA male connector
WiFi antenna2400~2483.5 MHz, 50 Ω, VSWR<2, gain** 5 dBi, omnidirectional, RP-SMA male connector

*Order code dependent. **Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

What's in the Box?

Standard Package Contains

  • RUT360
  • 18 W Euro PSU
  • 2 x LTE antennas (swivel, SMA male)
  • 2 x WiFi antenna (swivel, RP-SMA male)
  • Ethernet cable (1.5 m)
  • QSG (Quick Start Guide)
  • RMS Flyer
  • Packaging box

Images of the RUT360 router, LTE antennas, WiFi antennas, PSU, and Ethernet cable are provided.

Standard Order Codes

Product Codes and Regions

PRODUCT CODEHS CODEHTS CODEPACKAGE CONTAINS
RUT360******8517628517.62.00Standard package

Standard Order Codes by Region

PRODUCT CODEREGION (OPERATOR)FREQUENCY
RUT360 0*****Europe, the Middle East, Africa, Australia, APAC², Brasil, Malaysia
  • 4G (LTE-FDD): B1, B3, B5, B7, B8, B20, B28, B32¹
  • 4G (LTE-TDD): B38, B40, B41
  • 3G: B1, B3, B5, B8
RUT360 1*****North America
  • 4G (LTE-FDD): B2, B4, B5, B7, B12, B13, B25, B26, B29¹, B30, B66
  • 3G: B2, B4, B5

¹ LTE-FDD B29 and B32 support receiving only, and are only for secondary component carrier in 2×CA. ² Excluding Japan and CMCC. The price and lead-times for region (operator) specific versions may vary. For more information please contact us.

Mounting Options

DIN Rail Kit

ParameterValue
Mounting standard35mm DIN Rail
MaterialLow carbon steel
Weight57g
Screws includedPhilips Pan Head screw #6-32×3/16, 2pcs
Dimensions82 mm x 46 mm x 20 mm
RoHS Compliant✔️
IncludedDIN Rail adapter, Philips Pan Head screw #6-32×3/16, 2pcs for RUT2xx/RUT9xx
ORDER CODE088-00267
PRODUCT CODEPR5MEC00
HS CODE73269098
HTS CODE7326.90.98

Compact DIN Rail Kit

ParameterValue
Mounting standard35mm DIN Rail
MaterialABS + PC plastic
Weight6.5 g
Screws includedPhilips Pan Head screw #6-32×3/16, 2pcs
Dimensions70 mm x 25 mm x 14,5 mm
RoHS Compliant✔️
IncludedCompact plastic DIN Rail adapter (70x25x14,5mm), Philips Pan Head screw #6-32×3/16, 2pcs
ORDER CODE088-00270
PRODUCT CODEPR5MEC11
HS CODE73269098
HTS CODE7326.90.98

Surface Mounting Kit

ParameterValue
Mounting standardFlat surface mount
MaterialABS + PC plastic
Weight2x5 g
Screws includedPhilips Pan Head screw #6-32×3/16, 2pcs
Dimensions25 mm x 48 mm x 7.5 mm
RoHS Compliant✔️
IncludedSurface mounting kit, Philips Pan Head screw #6-32×3/16, 2pcs
ORDER CODE088-00281
PRODUCT CODEPR5MEC12
HS CODE73269098
HTS CODE7326.90.98

Spatial Measurements & Weight

Main Measurements

W x H x D dimensions for RUT360:

ItemDimensions (mm)
Device housing*100 x 30 x 85
Box173 x 71 x 148

*Housing measurements are presented without antenna connectors and screws; for measurements of other device elements look to the sections below.

Top View

Diagram showing top view dimensions of the RUT360 and its components.

Right View

Diagram showing right side dimensions of the RUT360 and its components.

Front View

Diagram showing front panel dimensions of the RUT360 and its components.

Rear View

Diagram showing back panel dimensions of the RUT360 and its components.

Mounting Space Requirements

Diagram illustrating approximate device dimensions with cables and antennas attached.

DIN RAIL

Diagram showing protrusion measurements of an attached DIN Rail.

Models: RUT360

File Info : application/pdf, 13 Pages, 1.34MB

PDF preview unavailable. Download the PDF instead.

rut360-industrial-lte-cat6-router

References

Adobe PDF library 15.00 Adobe Illustrator 25.1 (Windows)

Related Documents

Preview Teltonika Networks RUT955 Industrial Cellular Router Datasheet
Detailed datasheet for the Teltonika Networks RUT955, an industrial-grade 4G LTE router with WiFi, Ethernet, and multiple I/O options. Features include robust connectivity, security, and remote management capabilities.
Preview Teltonika RUTX11 Datasheet: Industrial LTE Cat 6 Router with WiFi & GNSS
Explore the Teltonika RUTX11 datasheet for detailed specifications of this industrial LTE Cat 6 router. Features include dual-band WiFi 5, GNSS, multiple Gigabit Ethernet ports, advanced networking, and security. Learn about hardware, installation, and mounting options for reliable connectivity.
Preview Teltonika RUTX11 Datasheet: Advanced LTE Router
Comprehensive datasheet for the Teltonika RUTX11, a powerful industrial LTE router with advanced features, connectivity options, and robust security. Learn about its hardware specifications, wireless capabilities, network protocols, and more.
Preview Teltonika RUTX12 Quick Start Guide - Setup and Specifications
Comprehensive quick start guide for the Teltonika RUTX12 dual LTE CAT6 router. Covers hardware installation, device login, technical specifications, radio details, bundled accessories, and safety information.
Preview Teltonika RUT260 Datasheet: Industrial 4G LTE Router Specifications
Detailed datasheet for the Teltonika RUT260, an industrial 4G LTE Cat 6 router. Features include high-speed connectivity, robust security, multiple VPN options, and extensive IoT platform support. View technical specifications, hardware details, and order information.
Preview Teltonika RUT301 Datasheet: Industrial Router Specifications
Comprehensive datasheet for the Teltonika RUT301 industrial router, detailing its hardware, features, network capabilities, security, power, physical specifications, and operating environment.
Preview Teltonika OTD140 Industrial 4G LTE Router Datasheet
Comprehensive datasheet for the Teltonika OTD140, a robust industrial 4G LTE router. Discover its features, hardware specifications, network capabilities, security protocols, and physical dimensions for industrial IoT and connectivity solutions.
Preview Teltonika RUT360 Quick Start Guide: Setup and Configuration
Concise guide to setting up and configuring the Teltonika RUT360 LTE Cat6 router, including hardware installation, login procedures, technical specifications, and safety information.