ONEX RV WIFI ROUTER

Welcome!

THANK YOU FOR PURCHASING OUR COMPANY RV WIFI ROUTER. TO OPERATE THE RV WIFI ROUTER CORRECTLY, PLEASE READ THE USER MANUAL CAREFULLY BEFORE USING. KEEP THESE INSTRUCTIONS AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

Installation Guide

Before powering on the device, insert the SIM card (or network card/SD card) into the SIM card slot as shown in the figure, then set it up and power on.

Remarks: The SIM card slot of this device only supports standard SIM card, Nano-SIM card, and Micro-SIM card. It needs to be restored to a standard SIM card with a ferrule to be inserted; otherwise, the card will not be ejected internally. Hot swapping is prohibited.

SIM Card Installation Types:

• SIM Installation: Diagram showing a SIM card being inserted into a slot labeled 'SIM'.
• USB Installation: Diagram showing a USB device being connected.
• SD Installation: Diagram showing an SD card being inserted.

Common SIM Card Size Diagram:

• Standard SIM size: 15*25mm
• Micro-SIM size: 12*15mm
• NANO-SIM size: 9*12mm

⚠️ Note: Hot swapping is prohibited.

Port and Button Descriptions:

Indicator Description:

Login Management Page

The default SSID is “WIFI-xxxxxx” or “WIFI-5G-xxxxxx” (where 'x' represents the last six digits of the MAC address). Wireless is not encrypted by default.

1. Log in through Management IP

The default admin address of the device is "192.168.1.1", and the password is "admin". Open your browser and enter the default IP address "http://192.168.1.1", then enter the default password to log in. (Google, Firefox, and Safari are recommended).

Configure the Native IP Address

After logging in through the default IP, select "Network" → "LAN", and modify the device login IP address according to your needs.

Navigation Tabs: ? [Home] | ? [Network] | ? [WiFi Setup] | ⚙️ [Advanced Setup] | ? [Service Application]

Under the Network tab, you will find:

• WAN | 3G/4G | LAN | DHCP | Terminal control | NAT Setup

LAN Settings:

[Save Button]

LAN Port Status Information:

On this page, you can set the network interface.

Configure Internet Access

1. WAN Setting

After logging in, select "Network" → "WAN" to set the Internet access mode. There are three Internet access modes: "automatic access", "PPPoE", and "fixed IP". Please choose the correct Internet access mode according to the requirements of your broadband operator.

Automatic access to the Internet (default)

Select "Auto Get". The device will automatically get the IP address from an ISP (Network server provider). Select this connection method when your ISP does not provide any IP network parameters.

Navigation Tabs: ? [Home] | ? [Network] | ? [WiFi Setup] | ⚙️ [Advanced Setup] | ? [Service Application]

Under the WAN tab:

• WAN | 3G/4G | LAN | DHCP | Terminal control | NAT Setup

[Save Button]

WAN Type State:

PPPoE dial-up

Select "PPPoE dial" and enter the account password provided by the operator. After saving, the account can be dialed automatically. After dialing successfully, the assigned IP address can be obtained for Internet access.

Navigation Tabs: ? [Home] | ? [Network] | ? [WiFi Setup] | ⚙️ [Advanced Setup] | ? [Service Application] | ⚙️ [System Management]

Under the WAN tab:

• WAN | 3G/4G | LAN | DHCP | Terminal control | NAT Setup

[Save Button] [Disconnect Button] [Reconnect Button] [Detection Button]

WAN Type State:

Configure Internet Access (Continued)

1. Fixed IP Internet access

Select the "fixed IP", then input the IP/subnet mask/gateway provided by the operator, and then save.

Navigation Tabs: ? [Home] | ? [Network] | ? [WiFi Setup] | ⚙️ [Advanced Setup] | ? [Service Application]

Under the WAN tab:

• WAN | 3G/4G | LAN | DHCP | Terminal control | NAT Setup

[Save Button]

WAN Type State:

2. Set up 3G/4G Internet access

After inserting the SIM card, the system dials automatically. The "3G/4G status information" obtains relevant IP address, MAC address, traffic, and other information, indicating that the dialing is successful.

Navigation Tabs: ? [Home] | ? [Network] | ? [WiFi Setup] | ⚙️ [Advanced Setup] | ? [Service Application] | ⚙️ [System Management] | ? [System Tools]

Under the 3G/4G tab:

• WAN | 3G/4G | LAN | DHCP | Terminal control | NAT Setup

3G/4G Configuration:

4G first: [Toggle Switch]

[Save Button]

3G/4G signal:

3G/4G Status Info:

Network Watchdog and Wireless Security

Reminders:

• The device supports WAN port and 3G/4G mode (special modules need to be installed or traffic charges should be paid).
• By default, if the WAN port has no access line or is interrupted, all Internet data will go through the 3G/4G network. When 4G is selected first, all Internet data will go through 3G/4G network. If 3G/4G fails, it will switch to the WAN port network.
• If 3G/4G operators have special requirements and need to fill in APN server related information, and if APN cannot be accessed from the external network, the device will be restarted repeatedly.

Network Watchdog Configuration:

To prevent repeated restarts, change "Advanced Settings" → "Execution Action" in "Network Watchdog" to "No action".

Navigation Tabs: ? [Home] | ? [Network] | ? [WiFi Setup] | ⚙️ [Advanced Setup] | ? [Service Application]

Under the Advanced Setup tab:

• Security Settings | DMZ host | Network watchdog

[Save Button]

3. Set the wireless password

The wireless password is not set by default. It is recommended to change the wireless password for your network security. Select "Wireless Settings" → "2.4g" to enable the wireless network, set the wireless name, set the encryption mode [It is recommended to use WPA2(AES) encryption mode], and the wireless password (to set the password, select "2.4g Advanced Option" and the password should be at least 8 digits), and click save.

Navigation Tabs: 2.4G | 5G | Tx power adjustment

2.4G Wireless configuration

[Collapse 2.4G Advanced Options Button]

[Save Button]

System Administration and Cloud Login

4. Change the system administration password

Click the [Menu/Settings Icon] icon to bring up a dialog box. Select the "Change Administrator Password" option to pop up the password service dialog box to make changes.

Password service Dialog:

[confirm Button] [cancel Button]

Enter a new password and click "Ok" to automatically jump to the login interface. Enter the new password to log in.

Cloud login

Cloud login can log in to the local setting page through the firewall, which is mainly used for remote management, remote assistance, and so on.

The cloud login function is turned off by default. If this function needs to be enabled, select "Service and Application" → "Cloud Login" interface to enable cloud login. The cloud login address will be generated after it is enabled, as shown in the figure below: (http://78a35133333058b9d9.os.ac-link.com:81). Enter this URL in your browser to log in remotely to the management device.

Navigation Tabs: Cloud login | Cloud management

Cloud login Settings:

Factory Reset

It is recommended to perform a factory reset when you forget the management password, cannot log in to the device, or the device configuration is abnormal.

Method 1:

When the system is running normally, press the router's Reset button with a spike for more than 8 seconds and wait for the device to restart.

Method 2:

Select "System Settings" → "Backup and Restore", and click the "Reset" button.

Navigation Tabs: ? [Home] | ? [Network] | ? [WiFi Setup] | ⚙️ [Advanced Setup] | ? [Service Application] | ⚙️ [System Management]

Under System Settings:

• System upgrade | Backup and recovery | General settings

Backup and Restore:

Note: Export and save the current configuration of the router to your computer, and import the backup file to restore the configuration in the future.

FAQ

What is the default Web IP address and default password?

The router's default IP address is 192.168.1.1, and the default password is ADMIN.

How do I restore the router to factory Settings?

When the system is running normally, hold the router's Reset button with a spike for about eight seconds and wait for the device to restart to complete.

How to do if I forget my router admin password?

The router's default administrative password is ADMIN. Try logging in with the default password. If the default password is not available, please restore factory Settings before using the default password to log in.

Why plug in the external network cable to complete the quick setup, but still unable to access the Internet?

Replug and unplug the network cable connected to the external network port, and turn off and restart the GPON /ADSL modem/home gateway for 10 minutes, then try again later. Verify that the username and password are correct, and confirm the account number, password, and payment with the network operator customer service.

Product Warranty & Inquiries

The following conditions are not covered by the warranty replacement, please note:

• Unauthorized repair, unauthorized disassembly.
• Product failure or damage caused by failure to install, use, maintain, or store in accordance with the instruction manual.
• Artificially injecting or tearing, altering the serial number of the product.
• Has exceeded the warranty period.
• External factors or human behavior lead to product damage, such as input inappropriate voltage, high temperature, liquid, mechanical damage, broken, severely oxidized or rusted, etc.
• Customer's damage caused by transportation during the repair process.
• Failure or damage caused by force majeure (such as fire, earthquake, etc.) or natural disasters (such as lightning strikes).
• Other failures or damages caused by problems other than product design, technology, manufacturing, quality, etc.

Warranty description

• Product warranty time is 1 year. The warranty method is for customer service. Warranty replacement is limited to this machine, packaging, and software production.
• The power adapter has a warranty period of 1 year. If the power adapter has obvious hard object damage, cracks, broken feet, serious deformation, damage to the power cord, disconnection, and bare core, it is not guaranteed, and users can purchase it themselves.
• The repaired machine, if it is under the warranty period, will continue to enjoy the warranty service. If it is less than 3 months from the end of the warranty period, the replaced product has a 3-month warranty from the date of replacement.
• The mailing fee for the returned product is the one-way responsibility of the sender.

User stub

In order to protect your rights and interests, please fill in carefully and keep it as a voucher for maintenance.

User Information: [Input Field]

Contact address: [Input Field]

Contact number: [Input Field]

E-mail: [Input Field]

Product certification

Model number: [Input Field]

QC: [Input Field]

date: [Input Field]

QC PASS 06 stamp.

Note: The final interpretation right of this manual belongs to our company. There are product changes, which are subject to the actual product without prior notice!

1 year warranty from date of purchase. For warranty evaluation, the purchaser must return the product to the dealer.

Manufactured by Team Noble Limited - +8675585278182

Australian distributor ONEX - (03) 8354 550 www.onex.com.au