Arctic Air Evaporative Air Cooler

What's Included

• Front Grill
• Fan Speed Button
• Light Button
• Fan Speed Indicator Lights (Low, Medium, High)
• On/Off Button
• Back Grill
• Water Tank
• USB Cable

Read entire manual before use. Save these instructions.

Setup

1. Place Arctic Air™ on a flat surface.

2. Open the water tank door and fill with water. A pitcher or measuring cup is recommended.

3. Plug a USB power adapter into an outlet. Then, insert the larger USB end of the cable into the adapter and the smaller end into the power port on the back of Arctic Air™. The larger USB end can also be plugged into a computer to power Arctic Air™.

Usage

1. Press the Power button to turn on Arctic Air™.
2. Set the Fan speed by pressing the fan button ⚙️. You can choose from Low, Medium, and High Mode. The indicator lights next to the button show the current speed.
3. Choose your light color by pressing the light button ?. You can select solid colors or a color-cycle mode. The color order is: Blue, Red, White, Teal, Purple, Yellow, Green, Color Cycle.
4. Choose your light brightness by pressing and holding the light button ? for 3 seconds; the tank will blink. Repeatedly press the fan button ⚙️ to choose between High, Medium, and Low, then stop. The tank will blink after 3 seconds to confirm the setting.
5. Press the Power button again to turn off your Arctic Air™.

Note: Running Arctic Air™ on HIGH mode for at least 5 minutes before powering off is recommended to allow for drying.

Low Water Indicator:

When the water level is low, the water tank will blink 3 times every 60 seconds in AMBER color. When the tank is filled again, the light will function normally.

Maintenance

Clean the water tank and inside of the unit once weekly using a non-abrasive cloth and mild dish soap.

For best continued results, change the filter every 6 months.

To purchase filters, visit www.ArcticAirFilter.com, call 844-260-1487, or e-mail arcticaircs@worldpackusa.com.

Changing the Filter:

The Water Filter should be changed every 6 months, or when Arctic Air™ is not functioning as expected. The water tank will light up AMBER until the filter is reset. To reset the filter, hold the fan button ⚙️ and the light button ? for 3 seconds until the tank is no longer AMBER.

1. Unplug Arctic Air™ from the wall.
2. Gently press the release tab on the bottom of the front grill and pull the grill down and away from the unit. Place it aside.
3. Grab the filter and carefully slide it out of the unit completely.
4. Place the new filter in Arctic Air™ as shown by the markings on the filter.
5. Insert the top tab of the front grill into the slot, and press the release tab back into place.

Tips

• Place Arctic Air™ on a raised surface such as a table, desk, or countertop. This is the most effective way to cool your personal area faster.
• Let the filter absorb water for at least 3 minutes after filling the tank and before use. This will provide cooler air more quickly.
• Try to stay within a few feet of Arctic Air™. You will feel the most benefit when sitting directly in front of the unit.
• Arctic Air™ will run for approximately 8 hours on a single fill at the Low fan speed. Even if the water tank is empty, the filter remains damp, and Arctic Air™ continues to cool.

Warnings

• Do not carry Arctic Air™ when filled with water. Some water may remain in the unit even if the tank appears empty.
• Use only clean water. Distilled water may be used if needed.
• Please read and follow regular maintenance as recommended in the “Maintenance” section of this guide.
• Arctic Air™ works best in non-polluted areas. Large dust/dirt particles can reduce the unit's lifetime.
• Use only in dry locations. If using in a moist area or environment, take care not to get water on external areas of the product.
• If a leak or spill occurs on the device, unplug Arctic Air™ and let it dry for 24 hours. Then, use as normal.
• Do not place in direct sunlight for extended periods.
• Before extended periods of non-use, empty the water tank, turn the unit on, and set to the highest fan speed for at least 4 hours. This will dry out the filter and the inside of your unit.
• Only use the original power adapter and cord supplied in the package.
• Do not touch the power supply or power cord with wet hands.
• Unplug Arctic Air™ when cleaning, removing/replacing the filter, or moving the device.
• For best results, place Arctic Air™ on a higher surface like a table or countertop.
• Do not place Arctic Air™ near a heater or any electrical equipment.
• Do not place the device in passageways or high traffic areas where there is a possibility of tripping or knocking it over.
• Do not allow any foreign objects inside Arctic Air™.
• Do not place items on top of Arctic Air™.
• Do not block the front and back grills of the device.
• Do not turn the device upside down.
• Do not submerge Arctic Air™ under water or other liquids.
• Do not place Arctic Air™ near open flames or fire sources.