Instructions For Installation & Operation

Getting Started

Before installing, locate the data label and note the model and serial number for guarantee registration.

Scan the QR codes for additional resources:

• QR code to download the IQFX App.
• QR code to register your warranty.
• QR code to download Surround Installation Instructions and Installation Videos.
• QR code to download a digital copy of IQFX Fire Installation Instructions.

Model: ____________________

Serial Number: _______________________

Contents Overview

This document provides comprehensive instructions for the IQFX 4232-16" Electric Fire, covering:

• Technical Specification
• Important Safety Information
• Contents of the Box(es)
• Inset Fire Opening Sizes & Installation Introduction
• Removing Glass/Parts & Fixings
• Installing the IQFX 16" Fire
• Internal Fuel Bed Layout & Log Positioning
• Installing the IQFX 16" Echo Trim
• User Instructions (Introduction, Manual Control, Remote Control, APP Control, Voice Control)
• Maintenance & Troubleshooting
• General Information
• Guarantee

Technical Specification

Dimensions (mm)

Visible Glass Area (mm)

Tolerance +/- 1mm

Specifications Continued

Model No: IQFX 16 4232 - Supply Voltage: AC 230-240V 50Hz, Maximum power consumption: 1538W.

Type of heat output / room temperature control

Important Safety Information

Read all instructions carefully before using the appliance.

• For indoor use only. Not suitable for outdoor use or poorly insulated spaces.
• If placing in front of a chimney opening, seal off with non-combustible insulation to prevent debris falling. Do not place in damp fireplaces. Consult a professional for chimney sealing.
• Do not use near baths, showers, or swimming pools.
• Must be fixed to a wall, mantel, or floor; not for free-standing use.
• Do not locate immediately below a socket-outlet.
• Appliance must be earthed.
• CAUTION: To avoid hazard from thermal cutout resetting, do not supply through external switching devices (timers) or circuits regularly switched by the utility company, or unstable electrical supplies.
• A 13A fuse is supplied. Replace only with a 13A BS1363A approved fuse or plug.
• If the power cord is damaged, it must be repaired by the manufacturer, authorized service centre, or a professional.
• DO NOT COVER: Warning to avoid overheating; do not cover the appliance or obstruct air inlet/outlet.
• Keep flammable materials (textiles, curtains) at least 1 meter from the air outlet.
• Keep the power cord away from hot surfaces and do not route it in front of the appliance.
• Do not use in rooms with explosive fumes (e.g., petrol) or when using solvents, glue, aerosol spray, or flammable paints.
• Children aged 8+ and persons with reduced capabilities may use the appliance with supervision and instruction for safe use, understanding the hazards.
• Children and vulnerable people require supervision as parts can become very hot and cause burns.
• Do not use in small, occupied rooms unless supervised, if occupants cannot leave independently.

Manual Handling

BEFORE STARTING INSTALLATION:

CAUTION: This appliance is heavy. Always seek assistance for unpacking and installation. Installation requires two adults. Obtain assistance if it feels too heavy.

• Use handles on the rear of the fire where possible.
• When lifting, keep your back straight, bend your legs, avoid twisting. Reposition feet as needed.
• Avoid top-heavy bending; bend from the knees, not the waist. Do not lean forward or sideways.
• Grip the fire with the palm of your hand; do not use fingertips for support.
• Keep the fire close to your body to minimize cantilever action.
• Use gloves for additional grip.

Contents of the Box(es)

Box 070998 – IQFX 16" (4232)

Box 050199 - Sold Separately

LED Light Set - 830mm Fly Lead plus 3m LED Lights can be purchased separately. Note: Compatible LED Light Sets are available from BeModern Ltd. Other makes may not be suitable and will void the warranty.

Please ensure all fixings are present before commencing installation. If anything is missing, please call Customer Services on 01914300901 or email at customerservices@bemodern.co.uk.

Inset Fire Opening Sizes & Installation Introduction

Opening Sizes

Follow the minimum clearances to fit the appliance into a back panel or cavity. Consider routing the power supply; a qualified electrician should conduct electrical installation. An accessible single socket is required.

For efficient safe running, a minimum aperture opening area for the IQFX 16" (4232) is advised:

Diagram showing fire opening dimensions A, B, C.

Installing the IQFX 16" (4232) Introduction

• Before you start: Do not dispose of packaging until all parts and fittings (listed on Page 6) are checked. Parts are packed inside and down the side of the fire. Refer to Page 8 for removing Box 3.
• If parts are missing, contact BE MODERN HELPLINE: 0191 430 0901.
• Recycle packaging responsibly.
• Ensure you have the right tools, space, and a clean dry working area.
• Protect the working surface to prevent damage to the fire surround, fire, or floor.
• IMPORTANT: If routing the power cable to the rear, take care not to crush or damage it when positioning the fire.

Removing the Glass/ Parts & Fixings Inside The Fire

Box 3 is located behind the front glass. The glass must be removed first.

1. Remove the 3 screws holding the glass retaining bracket. (See Diagram 2)
2. Note: Support the glass with your free hand while removing the bracket.
3. Once the bracket is removed, angle the glass out from the bottom, past the ledge, and lower it out of the top groove.
4. Note: Place the glass safely aside to avoid damage until refitting after the fuel bed is added.
5. Carefully remove the cardboard box behind the screen (See Diagram 3) and set aside.

Diagram 2 shows the 3 screws for the glass retaining bracket. Diagram 3 shows the cardboard box behind the screen.

Installing the IQFX 16" Fire

1. Locate the Clamping Bracket and Screws from Box 2.
2. Screw the back panel clamp bracket to the top of the fire using 3x 10mm Dome Head Screws. (See Diagram 4) There are three mounting positions depending on back panel thickness. The middle fixing is for 18mm/20mm panels, and the rear fixing is for 38mm/40mm panels.
3. The bracket may need to be bent by hand to fit. Note: The bracket is designed to prevent the fire falling forward and may not be a tight fit.
4. Position the back panel clamp bracket under the back panel at an angle, ensuring not to trap the power cable. (See Diagram 5) Note: Avoid scratching the hearth during installation.
5. Once the fire's lower rear edge clears the hearth, stand the fire upright and ease it back into the cut-out.
6. Apply light pressure to the fire to overcome the clamp's spring effect and move it fully into place. The bracket will then secure the fire.
7. To remove the fire, lift it vertically and angle it out of the back panel cut-out from the bottom.

Diagram 4 shows back panel clamp bracket mounting options. Diagram 5 shows positioning the fire with the clamp bracket. Diagram 6 illustrates fire removal.

Internal Fuel Bed Layout & Log Positioning

Dress the Fuel Bed and position the Logs. Locate Box 3.

Fuel Bed Dressing

Place Crystallised Pebbles / Smoked Crystals over the fuel bed. Enough material is provided to cover it.

Diagram 7 shows placement of pebbles/crystals.

Log Positioning

Diagram 8 shows the logs supplied with the IQFX 16".

Note: Locate the 'Log LED Light Assembly' from Box 3 and insert LED lights into logs with holes in the bottom. Connect illuminated logs to fuel bed connection points, hiding fly-leads.

For further guidance, visit: https://www.bemodern.com/diamondfireplaces/support/downloads/ or scan the IQFX QR code on the front page for 'how to' videos.

Diagram 9 shows an example of the 5 log set up for the IQFX 16", indicating illuminated logs.

Replacing The Glass

After dressing the fuel bed and positioning logs, replace the glass following the steps on Page 8 in reverse order.

Installing the IQFX 16" Echo Trim

1. With the fire securely installed, unpack the separately supplied fire trim.
2. If applicable, remove the trim's protective cover.
3. Position the 4x 10mm diameter magnets to the rear of the trim in the indicated positions. (Diagram 10)
4. Turn the trim to the front, drop the bottom trim louver down, place the last 10mm magnet on the rear centre top of the louver, and push back to contact the upper louver tab. (Diagram 10)
5. Place the trim over the fire, allowing magnets to contact the fire body to secure it. (Diagram 11)
6. This completes the installation of the IQFX 16" trim. (Diagram 12)

For Voice, Manual, Remote, and APP Control instructions, see pages 13-33.

Diagram 10 shows magnet placement for the trim. Diagram 11 shows attaching the trim. Diagram 12 shows the installed trim.

User Instructions - Introduction

WARNING: Do not operate if damaged or malfunctioning. Contact a qualified service engineer for inspection and repair.

WARNING: To reduce fire risk, keep flammable materials at least 1 meter from the air outlet.

Ensure the plug fits tightly in the outlet. Loose connections can cause overheating.

Do not disconnect power while the appliance is running. Use the remote to turn off the fire and ensure the main switch is off before disconnecting.

PREPARATION FOR USE

The appliance can be operated by manual control, remote control, or APP. The main power switch must be in the 'ON' position.

Batteries

Ensure handset batteries are new and inserted correctly.

Main Power Switch

Switch the main power ON before operating. A long beep indicates the fire is ready.

User Instructions - Manual Control

The appliance has manual control buttons for basic functions:

• Main (On / Off): Powers the appliance on/off.
• Stand-by: Turns all lights on/off. Flame effect fades out when turned off.
• Heater (Low, High, Off): Controls the heater. Press for low, again for high, again to turn off.
• Flame (On, change colour x 3, Off): Controls the flame effect and cycles through 4 colours.
• Wi-Fi pairing button
• 050199 LED mood light set connection point (Optional Extra)

Note: For full control, use the remote handset or APP. Appliance controls may lose memory settings if the main switch is turned off. Remote battery changes may reset flame function memory but not timer/clock settings.

Remote Control Pairing

The fire and remote are pre-paired. To pair a replacement remote, press and hold the "STAND-BY" button until two beeps, then press the power button on the remote. A single beep confirms pairing.

User Instructions - Remote Control

The remote control offers comprehensive functions:

Remote Display Icons: Battery power, Actual room temperature, Heating status, Temperature set.

User Instructions - APP Control

Download the APP and Register an account

1. Download the "My PRYZM" APP.
2. Register an account: Enter email/mobile, choose country, get verification code.
3. Enter the verification code.

Screenshots show app download links (Google Play, App Store), Pryzm app icon, and registration steps.

Add a device

1. Click "Add Device" or "+".
2. Download the "My Pryzm" APP.
3. Select Wi-Fi network (2.4 GHz required) and enter password. Click "Next".
4. Turn on the appliance. Press and hold the Wi-Fi button until 3 beeps; Wi-Fi indicator and fuel bed will flash.
5. Choose EZ Mode, confirm indicator is flashing, and click "Next".
6. Note: Ensure router is 2.4 GHz and distance to fireplace is at least 50cm.
7. Screenshots show the device adding process, Wi-Fi selection, and EZ Mode confirmation.

Add a device - continued

6. Start adding the device.
7. Once added, the fuel bed turns green and stops flashing.
8. Click "Done" to complete pairing.
9. If EZ Mode pairing fails, try AP Mode.
10. To use AP Mode: Press and hold the Wi-Fi button until 3 beeps, then continue holding until 5 beeps and the indicator flashes quickly.
11. Choose AP Mode, confirm flashing indicator, click "Next".
12. Connect your mobile phone to the device's hotspot (e.g., "SmartLife-XXX").
13. Go back to the APP and start adding the device.
14. Once added, the fuel bed turns green and stops flashing.

Screenshots illustrate the device adding progress, AP mode connection, and final successful pairing.

Using the APP - Home Screen

Click the fireplace name to enter the home screen. Control flame and heater modes.

Note: AUTO mode requires setting a daily/weekly timer.

Using the APP - Changing Colours

• Flame Effect Colour: Use the slider to adjust brightness (0%-100%).
• Fuel Bed Colour: Use the slider to adjust brightness (0%-100%).
• Downlight Colour: Use the slider to adjust brightness (0%-100%).
• Mood Light Colour: Use the slider to adjust brightness (0%-100%).

Screenshots show the app interface for selecting colours and adjusting brightness.

Using the APP - Setting Programs

• Flame Effect Program: Set up to 4 time periods per day with 4 different weekly schedules.
• Heating Program: Set up to 4 time periods per day with 4 different weekly schedules for temperature control.

Screenshots illustrate setting weekly timers for flame and heater, including start/end times and temperatures.

Using the APP - Setting Temperature Unit

Manually change the temperature using the on-screen controls.

Using the APP - Setting the Timer

Set timer functions via the APP.

Using the APP - Device Management

• Renaming your device: Click the device name to access settings and rename it.
• Creating a "Home": Navigate to "Home Management", click "Create a Home", enter a name, select location/rooms, and click "Save", then "Done".
• Adding a Member: From "Home Settings", select "Add Member" and choose "APP account" or "Others". Follow prompts to invite or add a member.
• Sharing a Device: Click the device, select "Share Device", then "Add Sharing". Choose to share via APP account or "Others" and send an invitation message.

Screenshots show device renaming, home creation, adding members, and sharing device processes.

User Instructions - Voice Control

Ensure your Amazon Alexa or Google Assistant APP is linked to the voice-controlled device. Link the fire APP by selecting "ME" then "Alexa" or "Google" from "Third-Party Voice Service".

Note: Phone, fire, and voice assistant APP must be on the same Wi-Fi for voice control to function.

Amazon Alexa Commands

Use commands like:

• Alexa, turn on/off <my fireplace>
• Alexa, turn on/off flame on <my fireplace>
• Alexa, set flame mode to auto/manual
• Alexa, turn on/off heater
• Alexa, set heat mode to auto/low/high
• Alexa, set flame colour to [1-4] or off (1=Orange, 2=Orange & Red, 3=Red & Orange, 4=Red)
• Alexa, set fuel bed colour to [1-9] or off (1=Red, 9=Cycle)
• Alexa, set down light colour to [1-9] or off (1=Red, 9=Cycle)
• Alexa, turn on/off mood light
• Alexa, set mood light colour to [1-14] or off (1=White, 14=Cycle)
• Alexa, set <my fireplace> temperature to [5-104] or "make it warmer/cooler".

Note: Timer cannot be set via Alexa voice control; use the APP.

Google Assistant Commands

Use commands like:

• OK Google, turn on/off <my fireplace>
• OK Google, turn on/off flame on <my fireplace>
• OK Google, set flame mode to auto/manual
• OK Google, turn on/off heater
• OK Google, set heat mode to auto/low/high
• OK Google, set flame colour to [1-4] or off (1=Orange, 4=Red)
• OK Google, set fuel bed colour to [1-9] or off (1=Red, 9=Cycle)
• OK Google, set down light colour to [1-9] or off (1=Red, 9=Cycle)
• OK Google, turn on/off mood light
• OK Google, set mood light colour to [1-14] or off (1=White, 14=Cycle)
• OK Google, set timer on <my fireplace> to [30 mins - 10 hours]
• OK Google, set <my fireplace> temperature to N Celsius [5-40] or N Fahrenheit [41-104].

Maintenance

WARNING: Disconnect from power supply before maintenance or cleaning until cooled.

Remote Handset Battery Replacement

• Battery status indicators: Full, Half Full, Empty.
• Replace batteries annually. Uses 1.5V AAA alkaline batteries.
• Dispose of old batteries responsibly.

Cleaning the Fire

• Cleaning or polishing products are not recommended.
• Fingerprints on glass: Use a soft, damp, lint-free cloth with household glass cleaner. Dry thoroughly with a clean, lint-free cloth or paper towel.
• CAUTION: Do not use abrasive cleaners. Do not spray liquids directly onto the unit.

Troubleshooting

For further assistance, contact Customer Services on 01914300901 or customerservices@bemodern.co.uk.

General Information

Environment

Meaning of crossed-out wheeled dustbin: Electrical appliances must not be disposed of as unsorted municipal waste. Use separate collection facilities. Contact local government for disposal systems. Improper disposal can release hazardous substances. Retailers are legally obligated to take back old appliances for disposal.

Compliance

This fire complies with:

• Safety Standards EN 60335-1 and EN 60335-2-30 (Low Voltage Directive 2014/35/EU).
• EMC standards EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 (European Electro Magnetic Compatibility 2014/30/EU).
• RED standards EN300220-2, EN301489-1, EN301489-3, EN6247 (European Radio Equipment Directive 2014/53/EU).
• UK compliance with BS 60335-1, BS 60335-2-30 (Electrical Equipment Safety Regulations 2016), BS 55014-1, BS 55014-2, BS 61000-3-2, BS 61000-3-3 (Electro Magnetic Compatibility Regulations 2016), and BS 300220-2, BS 301489-1, BS 301489-3, BS 6247 (Radio Equipment Regulations 2017).
• RoHS Compliant: Restricts hazardous substances in electrical and electronic equipment.

Technical Components

Electric Fire Guarantee

The IQFX Fire comes with a 1-Year standard warranty (parts and labour). A 2-year extended warranty is available by registering within 28 days of purchase at: https://www.bemodern.com/diamondfireplaces/support/warranty/ (covers parts only for years 2 & 3).

Registration is not required for the standard 1-year warranty. For information or to register by phone, contact Customer Service on 0191 430 0901.

Guarantee Terms:

1. Applies to all products manufactured by the Company, purchased and installed within the UK by the original purchaser.
2. Proof of Purchase is required.
3. Guarantee does NOT apply to:
• Damage from installation workmanship.
• Damage from misuse or lack of normal care.
• Damage from malfunction or inadequate installation.
• Damage from misuse, accident, or unauthorized alterations.
4. During the guarantee period, defects from manufacturing or materials will be made good (repair/replacement) at the Company's option, provided the product was installed per Be Modern recommendations. The purchaser must uninstall and make the product available for collection.

This Guarantee does not affect your statutory rights.

For service, contact the retailer who supplied the product.

Be Modern Ltd.
19-34 Bedesway
Bede Industrial Estate
Jarrow
Tyne and Wear NE32 3BE
Tel: (0191) 430 0901
Fax: (0191) 430 9522
Website: Bemodern