DELONGHI PAC210U Owner's Manual

IMPORTANT INFORMATION

When using electrical appliances, basic safety precautions should always be followed, including the following:

• Read all instructions.
• To protect against fire, electrical shock, and personal injury, do not immerse the cord, plug, or appliance in water or other liquid.
• Close supervision is necessary when any appliance is used by or near children.
• Do not operate with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair, or adjustment.
• The use of accessory attachments or spare parts not recommended by the appliance manufacturer may result in fire, electrical shock, or personal injury.
• Do not use outdoors.
• Do not use the appliance for other than its intended use.
• Do not place any strain on the power cord. Avoid twisting and/or tangling.
• Ensure that the outlet vent of the exhaust hose is kept debris-clear and obstruction-free.
• Ensure that ventilation holes on the rear of the machine and front louvers are not blocked.
• The Pinguino should not be installed where the atmosphere could contain combustible gases.
• Avoid using Pinguino in oily or sulphurous atmospheres or near sources of heat.
• Wait at least 3 minutes before restarting, after the air-conditioner has been switched off or the thermostat setting changed.
• Before moving the air-conditioner, empty water from the collection tray (see instructions for drainage at page 13).
• Do not place hot or heavy objects on the appliance.
• Clean air filter every week (see instructions at page 13).
• Important: If you need to use an extension cord, please be sure to use a heavy-duty extension cord (minimum 14 gauge).

SAVE THESE INSTRUCTIONS

SPECIFICATIONS

*Data according to pending standard testing procedures subject to review by the U.S. Dept. of Energy.

A HE (High efficiency) system with low energy consumption has been installed on this appliance. Such system needs about 4 minutes, once the appliance has been started, to produce cold air.

OPTIMUM OPERATING RANGE

ILLUSTRATED MAIN FEATURES LIST

The main features of the Pinguino PAC 210 U are:

• Air outlet grid: Located on the front panel for air discharge.
• Timer cover: A sliding cover to adjust the timer settings.
• Castor: Wheels for easy mobility.
• Castor stops: Devices to prevent the unit from rolling.
• Water collecting tray: Collects condensed water.
• Air filter: Located behind the air intake grid to clean the air.
• Air intake grid: Allows air to enter the unit.
• Exhaust hose: Connects to the unit to expel hot air.
• Power cable compartment: Stores the power cord.
• Manually resettable red button: Likely a reset switch.
• Water collecting tray drainage tube: For emptying the water tray.

ILLUSTRATED ACCESSORY LIST

Check that all parts listed in Table 1 are included:

INSTALLATION

PERMANENT INSTALLATION

The Pinguino accessories include two sets of flanges and stoppers, to be mounted in different locations (e.g., two different rooms). Once installed, these vents (flanges) are the only items needed for using the Pinguino.

Permanent installation outlet holes must be in an exterior wall, and the opening diameter should not exceed 3 1/2 inches.

Installation Methods:

• A1 (fig. 2): Through a window pane. Shows a cross-section of a window with a hole and a flange/stopper installed.
• A2 (fig. 3): Through the wooden base-section of a door or window. Shows a cross-section of a wooden frame with a hole and a flange/stopper installed.
• A3 (fig. 4): Through the wall. Shows a cross-section of a wall with a hole and a flange/stopper installed.

In case of fixed installation, air discharged from the rear hose has been extracted from the room where the appliance is installed. Check that the room (especially if small) is not "air-tight"; a drop in pressure would cause irregular functioning, which could consequently activate the reset switch. Air entering through door and window cracks is normally sufficient. If deemed necessary, leave a door ajar (approx. 1 cm is enough).

TEMPORARY INSTALLATION

Note: In both cases (permanent and temporary installations), make sure that the Pinguino is positioned on level ground. If necessary, use the two caster stops for the front casters.

This installation makes it easy to use the Pinguino in any room, provided there is a window or a door; it allows you to use the Pinguino immediately.

Suction discs may be used to keep the window or door closed.

The Pinguino is equipped with an adjustable window bracket. If you have a sash window, place the bracket on the window sill, extend the bracket fully within the window frame, and lower the window onto the bracket. Insert the nozzle of the exhaust hose into the slot, then connect the hose to the air conditioner (fig. 7). Thanks to the wing nut, it's possible to use the window bracket also for sliding windows. Position the hole of the bracket so to allow a correct installation of the exhaust hose (see the following instructions).

SET UP INSTRUCTION

For permanent installation, place the Pinguino near the outlet opening in the wall or window (where it is meant to be used). The diagram below shows the correct way to install the exhaust hose:

• Step 1: Water collects at this point [❌ NO]
• Step 2: Bend this section [✔️ YES]
• Step 3: Bend this section [✔️ YES]

ELECTRICAL CONNECTION

Check that the power supply voltage is 115 V ~ 60 Hz.

Important: If you need to use an extension cord, please be sure to use a heavy-duty extension cord (minimum 14 gauge).

Before connecting the Pinguino to the power supply, make sure that all switches on the front control panel are in the OFF position.

Connect the power cord found in the storage compartment at the rear of the Pinguino.

FINAL CHECK

In order to obtain the maximum performance from your air-conditioner, make sure that:

• Doors and windows of the room to be air-conditioned are closed (with the exception of temporary installation where a partially opened window is necessary).
• The door is closed.
• Shade the room as far as possible from direct sunlight by drawing curtains and/or lowering blinds or shutters, for economical and efficient air-cooling.
• Ensure that intake and outlet vents (refer to installation diagrams) are not blocked.
• Make sure there are no sources of heat in the room.

DESCRIPTION OF PINGUINO PAC 210 U CONTROLS

The Pinguino PAC 210 U features the following controls:

• ON/OFF button (A): Powers the unit on or off.
• ON/OFF pilot light: Indicates when the unit is powered on.
• Thermostat: Adjusts the desired temperature.
• Timer ON/OFF button: Used for programming operating times.
• Timer ON/OFF pilot light: Indicates when the timer function is active.
• Selecting fan speed button (C): Adjusts the fan speed.
• “Alarm” pilot light: Indicates a fault condition.
• Timer notches: On the timer dial, each notch represents 15 minutes.

SETTING THE TIMER

The programmer/timer, like all clocks, must be set to the exact time. For example, if it is 4:00 p.m., turn the dial in a clockwise direction (following the direction of the arrow) until the number 4 is lined up with the arrow pointer (the arrows indicate 4:00 p.m. approximately).

Note: Never turn the dial in an anti-clockwise direction!

The timer is, in effect, an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or there is a power failure, the programmer stops (the clock is then “slow”) and must be re-set.

The unit can be used in either programmed or non-programmed mode.

PROGRAMMED MODE

1. Release the B timer button.
2. Set the operating times by pushing out the notches on the dial corresponding to the period required (each notch represents 15 mins.). Example: from 9 to 11 a.m.
3. Check that the timer indicates the correct time (see instructions on setting).
4. Select the desired function as shown in the chart overleaf. The unit will now switch on and off each day at the selected times.

Note: To override the programmed operating times, simply press the ON/OFF key.

NON-PROGRAMMED MODE

1. The B TIMER button must be pressed.
2. Select the desired function as shown in the chart on the following page.

N.B: For technical reasons, the temperature is not expressed in degrees but by a line increasing in thickness. We therefore recommend that when starting up the appliance, the thermostat be turned to maximum (thick green line = maximum cold). When the desired temperature has been reached, turn the thermostat slowly away from the maximum cooling position until the appliance switches off. Leave the thermostat in this position. The air-conditioner is now programmed to maintain the exact temperature at all times.

After switching the appliance off, wait at least 3 minutes before switching on again.

HOW TO START UP THE CONDITIONER

(See control panel on the previous page)

1. Plug the appliance into the mains.
2. Select the “programmed” or “non-programmed” mode (see previous page).
3. Select the fan speed required by pressing the “Fan speed” key C.

AIR-CONDITIONING

• Key A (ON/OFF) for conditioning must be released.
• Turn the thermostat to Max. Cold.
• Press key A (ON/OFF). The ON/OFF signal lamp (conditioning) will come on.
• The appliance comes on. If not, refer to page 14.
• To switch off the appliance, press key A (ON/OFF main switch).

MAINTENANCE

PRECAUTIONS

• During cleaning and normal maintenance operations, remember to disconnect the plug.
• Under no circumstances should the appliance be washed with running water. Damage could be caused to the electrical circuit.

CLEANING OF EXTERNAL HOUSING

• Use only mild soap and water. Do not use chemical cleaners.
• Clean with a damp cloth and dry thoroughly with a clean dry cloth.

CONTROLS AT THE BEGINNING OF THE SEASON

• Carefully follow the installation procedure.
• Check for any defects in the power cord and plug.

AIR FILTER CLEANING

Maintenance of air filter

A clogged air filter reduces the quantity of circulating air and the efficiency of the appliance. Clean the filter every week using a vacuum cleaner.

Removal and replacement of air filter

Gently pull the filter upwards. Push down to replace.

Cleaning procedure

To remove dust deposited on the filter, use a vacuum cleaner. If it is very dirty, soak in lukewarm water and rinse thoroughly. The temperature of the water must be kept below 104°F. After washing, leave the filter to dry before replacing.

END OF SEASON OPERATIONS

1. Disconnect the plug.
2. Remove the plug from the drainage tube to empty the water collecting tray.
3. Remove the exhaust hose.
4. Clean the filter and dry well before replacing.
5. Cover the appliance with a polyethylene bag to prevent dust from entering. You can use the polyethylene bag included into the packaging.

TROUBLESHOOTING

SERVICING

In case of malfunction, turn off and disconnect the Pinguino from the power outlet and contact our Service Centre for qualified assistance. Toll-free number: 1-800-322-3848.

LIMITED WARRANTY (FOR UNITED STATES ONLY)

We warrant each DE'LONGHI AIR-CONDITIONER to be free from defects in material and workmanship. Our obligation under this warranty is to provide one year parts and labor free from purchase date, with an additional four (4) years on any part of the sealed system consisting of the compressor, evaporator, condenser, and factory-connected refrigerant tubing. This warranty shall apply only if the AIR-CONDITIONER is used in accordance with the factory directions which accompany it, and on Alternating Current (AC) circuit. This warranty is in lieu of all other warranties and representations, expressed or implied, and all other obligations or liabilities on our part. We do not authorize any other person or company to assume for us any liability in connection with the sale or use of our AIR-CONDITIONER. This warranty shall not apply to any AIR-CONDITIONER which shall have been repaired or altered outside our factory, nor shall it apply to any AIR-CONDITIONER which has been subjected to misuse, negligence, or accidents.

If repairs become necessary or spare parts are needed, please write to:

De'Longhi America Inc.
Park 80 West Plaza One, 4th floor
Saddle Brook NJ 07663

or call Service Tel. No: 1-800-322-3848.