ThermoPro TP60S Wireless Indoor/Outdoor Humidity and Temperature Monitor Instruction Manual

Introduction

Congratulations on your purchase of the wireless indoor/outdoor humidity and temperature monitor. This device allows you to monitor outdoor and indoor temperature and humidity levels from the comfort of your home.

General Warning

⚠️ DANGER! This device contains electronic components powered by a power source (power supply and/or batteries). Do not allow children to use the device unattended. Use the device only as described in this manual to avoid the risk of electric shock. Children should only use the device under adult supervision. Keep packaging material, such as plastic bags and rubber bands, out of the reach of children, as they pose a choking hazard.

Keep batteries out of the reach of children. Ensure batteries are inserted correctly. Empty or damaged batteries could cause burns if they come into contact with the skin. Wear adequate gloves for protection if necessary.

⚠️ DANGER! Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire, or an explosion!

ℹ️ NOTE! Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can arrange for the device to be repaired, if necessary.

Notes on Cleaning

Separate the device from the power supply or remove the batteries before cleaning. Only use a dry cloth to clean the exterior of the device. Do not use any cleaning fluid to avoid damaging the electronics.

Hints and Tips

If the receiver does not connect to the transmitter, try the following:

• Press and hold the CHANNEL/SYNC button on the base station and then press the TX button on the transmitter.
• Relocate the base station and/or the remote unit until a connection is found.
• Signals from other electronic devices may cause interference. Place the base station and receiver away from these devices.
• The transmitter may not function properly in extreme temperatures due to battery power. Replace the batteries, or the unit will resume proper function in more moderate weather.
• If the base station is attached to a refrigerator or a metal object by magnet, the transmission range may be shorter. Remove the base station from the refrigerator or metal object, or place the base station and remote sensor as close as possible.

If the Humidity is lower than 10%, it will display LLL.

Warnings

• Do not subject the unit to excessive force, shock, dust, temperature, or humidity.
• Do not immerse the unit in water.
• Do not remove any screws.
• Do not dispose of this unit in a fire. IT MAY EXPLODE.
• Keep the unit away from small children. The unit or parts of the unit might be a choking hazard.
• Never attempt to recharge the batteries using any other methods.
• Dispose of the unit legally and recycle when possible.

Components

1. One base station unit (Receiver).

2. One remote sensor (Transmitter).

Although the remote sensor is designed to be rainproof, it must always be placed upwards so that rain won't get inside the sensor through the vent holes on the bottom. These vent holes allow the sensor to detect environmental temperature and humidity more precisely and quickly.

Indoor Base Station (Receiver) Features

The display shows:

• Outdoor temperature and humidity (CH1)
• Indoor temperature and humidity

Features:

• LCD display: Shows current outdoor/indoor temperature and humidity.
• Battery Compartment: Holds 2 AAA batteries to power the unit.
• Design: Tabletop and wall-mounted.
• Indoor Temperature range: -4°F to 158°F (-20°C to 70°C).
• Humidity range: 10% to 99%.
• Temperature display unit: °C and °F selectable.
• Temperature Resolution: 0.1 °C/°F.
• Humidity Resolution: 1%.
• Low battery indication.

Buttons:

• CHANNEL/SYNC: Press once to display temperature and humidity from up to 3 outdoor remote sensors. Press and hold to enter synchronization mode.
• MAX/MIN/CLEAR: Press once to display the maximum or minimum temperature and humidity. Press and hold to clear history data.
• °F/°C/ALL-TIME/24: Press to select temperature display in °C or °F. When MAX or MIN is displayed, press once to set the data record time interval between ALL TIME or 24 hours. (Note: ALL TIME and 24 hours refer to the period since the last manual clear or battery installation.)

Temperature & Humidity Trend

• ⬆️ indicates the temperature & humidity is in an increasing trend.
• ➡️ indicates the temperature & humidity is in no change trend.
• ⬇️ indicates the temperature & humidity is in a decreasing trend.

Outdoor Remote Sensor (Transmitter) Features

The remote sensor is designed to be rainproof and wall-mounted.

Features:

• Battery Compartment: Holds 2 AAA batteries.
• Design: Rain-proof and wall-mounted.
• Outdoor Temperature range: -4°F to 158°F (-20°C to 70°C).
• Humidity range: 10% to 99%.

Buttons:

• CHANNEL Selector (1,2,3): Slide to set Channel 1, 2, or 3.
• RESET: Press once to reset the remote sensor.
• TX: Press to send temperature/humidity data to the receiver manually.

Battery Installation and Setup

Remote Sensor:

1. Open the battery compartment.
2. Slide the channel selector switch inside the compartment to your desired channel (1, 2, or 3). For additional remotes, select an unused channel.
3. Insert 2 AAA batteries according to the polarity markings. Replace the battery compartment cover.

Base Station:

4. Open the battery compartment at the back of the base station.
5. Insert 2 AAA batteries according to the polarity markings. Replace the compartment door.
6. Press the °F / °C button at the back of the base station to display the temperature in °F or °C.

Note:

• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon zinc), or rechargeable (nickel cadmium) batteries.
• For maximum performance in normal conditions, use good quality alkaline batteries.
• A low battery icon will appear on the base station display if the battery power is low.

Synchronize Remote Sensors with The Base Station

Each time batteries are replaced or connection is lost, follow this synchronization process:

1. Position the remote sensor near the base station.
2. When batteries are installed in the base station, the RF signal icon ? (top left of display) will flash for 3 minutes, indicating synchronization mode.
3. If 3 minutes pass and the RF signal icon is no longer flashing, press and hold the CHANNEL/SYNC button on the base station for 3-4 seconds until the RF signal icon flashes again to re-enter synchronization mode.
4. Install batteries in the remote sensor. Wait a moment or press the TX or RESET button inside the remote sensor's battery compartment. The remote sensor's temperature/humidity will display on the base station, indicating synchronization is complete.
5. For additional remote sensors (up to 3 total), repeat the above steps.
6. If multiple sensors are registered, press the CHANNEL/SYNC button on the base station to select the desired channel to display permanently. Press until a circular arrow ⌛️ appears under the channel number. The unit will then auto-scroll through channels every 5 seconds. Press CHANNEL/SYNC again until the circular arrow disappears to stop cycling.

Place the Base Station and Remote Sensor

1. The indoor base station (receiver) should be placed in a well-ventilated indoor area, away from vents, heating/cooling elements, direct sunlight, windows, doors, or other openings.
2. The remote sensor (transmitter) can be placed flat indoors or outdoors. Ensure it is within transmission distance of the base station with minimal obstructions.
3. Both the base station and remote sensor can be wall-mounted.

NOTE: Although the remote sensor is rainproof, it must be placed upwards so rain does not enter through the bottom vent holes, which are essential for accurate temperature and humidity detection.

Maximum & Minimum Recorded Temperature & Humidity

1. Press MAX/MIN/Clear to display the highest indoor/outdoor temperatures/humidity recorded since the last reset (MAX shown).
2. Press MAX/MIN/Clear again to display the lowest recorded values (MIN shown).
3. To clear and reset max/min records, press and hold MAX/MIN/Clear for 3 seconds while MAX or MIN is displayed.
4. When MAX or MIN is shown, press the ALL-TIME/24 button once to set the data record interval between ALL TIME or 24 hours.

Purchasing Additional Remote Sensors

The model number for the remote sensor is TPR65. Additional sensors can be ordered directly from Amazon or ThermoPro by contacting customer service.

Specifications

• Transmission frequency: 433 Mhz.
• Maximum transmit power: 8 mW.
• Transmission range: Up to 200 ft. (may be shorter due to interference).
• Indoor Temperature range: -4°F to 158°F (-20°C to 70°C).
• Outdoor Temperature range: -4°F to 158°F (-20°C to 70°C).
• Humidity range: 10% to 99%.
• Temperature tolerance: +/- 2.0°F (+/- 1.1°C).
• Humidity tolerance: ±2% from 30% to 80%; ±3% below 30% and above 80%.
• Power: 2 x AAA 1.5V for base unit and 2 x AAA 1.5V for remote sensor.

FCC Statement of Compliance

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity

Hereby, the manufacturer declares that this product complies with the basic requirements and applicable regulations of the EMC Directive 2014/30/EU. The complete declaration of conformity can be found at: https://itronicsmall.com/eu-declaration-of-conformity/

Disposal

Meaning of the “Dustbin” Symbol ?

• Protect our environment: do not dispose of electrical equipment in domestic waste.
• Please return any electrical equipment that you will no longer use to the collection points provided for their disposal.
• This helps avoid the potential effects of incorrect disposal on the environment and human health.
• This will contribute to the recycling and other forms of reuse of electrical and electronic equipment.
• Information concerning where the equipment can be disposed of can be obtained from your local authority.

CAUTION: Batteries/rechargeable batteries must not be disposed of with household waste!

• The batteries must be removed from the appliance.
• Take spent batteries to the appropriate collection point or to a dealer.
• Your town or local authority can provide information about public collection points.

This symbol can be found on batteries/rechargeable batteries which contain hazardous materials:

• [Pb] = contains lead
• [Cd] = contains cadmium
• [Hg] = contains mercury
• [Li] = contains lithium

Limited One-year Warranty

ThermoPro warrants this product to be free of defects in parts, materials, and workmanship for a period of one year from the date of purchase. Should any repairs or servicing under this warranty be required, contact Customer Service by phone or email for instructions on how to pack and ship the product to ThermoPro. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Customer Service

Call or Text: 1-877-515-7797 (USA & Canada only) / 44-808-164-1683 (UK)

Email: service@buythermopro.com

Hours: Weekdays 8:00 AM - 8:00 PM EST (USA & Canada only) / 1:00 PM - 12:00 AM CET (UK)