Rock Space Smart Protective Film Plotter ZC1 Max (V1.0)

Product List

Smart Plotter ZC1 Max Host

• Blade Kit
• Blade
• Adapter
• Power Cord
• Film Installation Accessories

Appearance And Function

1 Driver: Control the lateral movement of the Blade Kit

2 Blade Kit: Cutting protective film

3 Platen Roller: Fixes protective film

4 Lateral Panel: Set limit of position and movement for protective film

5 Operation Display: Touch to control device operation

6 Power Switch: Starting device

7 Power Interface: Link power

8 Pressing Bar: Press to control the platen roller to lift or fall

9 Blade Kit Clamp: Lock the knife handle to secure the blade kit

Instructions

1. Install Blade Kit

1. Loosen the blade kit clamp counterclockwise.
2. Set to scale "1".
3. Put into the groove in a vertical position.
4. Tighten the blade kit clamp clockwise to lock the knife handle.

2. Power On

Connect the power cord to the adapter and then connect the power cord to the power socket. To ensure the normal operation of the device, please use 100-240 volts AC power. Connect the adapter to the power interface of the device. Install the blade kit on the knife holder to ensure it is fixed correctly. After connecting, press [Power Switch] to start the device.

Notice:

Adjust blade: Rotate the knob to control the length of the blade. Lengthen the blade in the direction of symbol "+" and shorten the blade in the direction of symbol "-".

Replace blade: Press the button to remove the old blade and then put in the new blade. (The built-in magnet can absorb the blade)

3. Cut Film

When using it for the first time, you need to click [select language] to complete the language setting, then you need to click [set WIFI] to complete WIFI connection.

(1) Please prepare a protective film to be cut as shown in the figure. Confirm that the protective film is flat and complete, without bending, folding or missing layer. [Checkmark symbol] [Cross symbol]

(2) Press down the pressing bar to lift the platen roller, and place the protective film in the dotted area as shown.

(3) Slowly lift the pressing bar so that the platen roller presses the protective film.

(4) After the system starting normally, enter the home page.

(5) Enter keywords in the search box, search for the product model you need to cut and select the film code of the corresponding specification according to the recommended guidelines on the screen.

(6) After confirming the relevant information, click [OK] to start cutting the film.

(7) After cutting, the protective film will be pushed out automatically. Take out the protective film and finish cutting.

4. Activate Film Code

Enter [Consumable identification code] found on the protective film package box, and then click [ADD].

Product Specification

Cautions

[Finger touching blade symbol] Don't touch the tip of the blade with your finger. It may hurt your finger.

[Liquid/metal objects symbol] Liquid or metal objects are not allowed to enter into the machine. These objects may cause fires.

[Power cord symbol] Do not destroy or arbitrarily replace the original power cord. Do not bend, pull or bind the power cord excessively or place the power cord under heavy object. This may cause damage to the power supply, resulting in an electric shock or fire.

[Unplugging device symbol] If you do not use the device for a long time, remove the power cord from the socket. Otherwise, it may cause a fire.

[Firm surface symbol] The device should be placed on a firm surface. Otherwise, the device may fall down and get damaged.

[Unplugging cable symbol] When the power cord is unplugged from the socket, the plug should be unplugged instead of the cable. Pulling a cable strongly may cause an electric shock or fire.

[Thunderstorm symbol] It is forbidden to use in thunderstorm and lightning weather. Lest the machine be damaged by electric shocks.

5. How to Install the Film

1. Wipe the screen with the cleaning kit.
2. Tear off the outer frame of the film from the tearing position at the upper right corner of the front of the film.
3. Place the film flatly and remove the white release film.
4. Remove the hole film and tear off the middle auxiliary strip; (Please fix the film with your index and middle fingers).
5. Place the film flatly on the screen and hole of the phone precisely and press the auxiliary strip (Be careful not to touch either end of the auxiliary strip).
6. Lift the upper part of the film and pull back 2cm, then push forward slowly with a scratch card from the middle of the auxiliary strip.
7. Then lift the lower part of the film and pull back 2cm, then push forward forcefully with a scratch card.
8. Use a cleaning cloth to smooth the curved surface if necessary.
9. Finally uncover the surface PET film and finish installing the film.

Precautions

[Power button symbol] Press the power button to stop urgently during cutting.

[Driver symbol] Please don't move the driver manually when powered on to avoid damage to the machine.

[Blade symbol] Please don't touch or bump the blade against anything hard for it is sharp and fragile.

[Blade replacement symbol] In order to ensure perfect cutting effect, it is suggested to replace the blade and the rubber strip every 500 times of cutting or 3 months of use.

[App shutdown symbol] Please shut down the machine normally through the App, and please don't unplug the power cable directly, for it may cause irreversible damage to the machine.

[QR code symbol] If you are a user beyond China, please scan the QR code to follow us on Facebook for more information.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located for operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.