Rock Space AC1200 Dual Band WiFi Repeater
Quick Install Guide
Model: RSD0608
LED Descriptions
| LED | Status | Description |
|---|---|---|
| Power LED | Solid on | The repeater has started. |
| Blinking | The repeater is starting. | |
| Off | The repeater is not powered on. | |
| WPS LED | On | A WPS connection has been established. |
| Blinking | A WPS connection is being established. | |
| Off | The WPS function is disabled. | |
| Signal LED | Solid blue | The repeater has connected to your existing WiFi router/modem, and its position is proper. |
| Solid red | The repeater is too far away from the router. Relocate the repeater closer to the router. | |
| Off | The repeater does not connect to your WiFi router. |
Button Description
| RST | Use the end of a paper clip or a similar object to press and hold this button for about 8 seconds with power on, and then release it to restore the extender to factory settings. |
Method 1: Extending Your WiFi Network Using Web UI
1. Power on the Repeater
Plug the repeater into a power outlet near the router in the same room.
Wait until the PWR LED turns solid blue.
2. Extend Your WiFi Network
- Connect your WiFi device to the repeater's WiFi network: rockspace_EXT. Ensure that the Mobile Data (if any) is disabled.
- Start a web browser, enter
http://re.rockspace.localor192.168.0.254in the address bar to log in. Create a login password for later attempts (recommend). - Select a WiFi network (SSID) you want to extend.
- Enter the password of the WiFi network you want to extend. The extended WiFi network SSID will be your existing WiFi network's SSID with a suffix _EXT or _5GEXT. The WiFi password of the repeater is the same as your WiFi router.
Wait a moment, the 'Extended successfully!' page appears.
3. Relocate the Repeater
- For better performance, plug the repeater into an outlet halfway between the router and the WiFi dead zone. The location you choose must be within the range of your existing WiFi network.
- Wait until the Signal LED turns blue. If not, relocate the repeater closer to the router.
- Connect your WiFi devices to the repeater using the SSIDs set by yourself, or your router's SSID with a suffix _EXT/5GEXT, and using the WiFi password same as your WiFi router.
Method 2: Extending Your WiFi Network Using WPS
You can use Method 2 if your router has a WPS button (possible icons of a WPS button: ?WPS, ?, or ?). Otherwise, use Method 1.
1. Power on the Repeater
Plug the repeater into a power outlet near the router in the same room.
Wait until the PWR LED turns solid blue.
2. Extend Your WiFi Network
- Press the WPS button on the router and within 2 minutes press the WPS button on the repeater.
- Wait until the Signal LED on the repeater turns solid blue. If the Signal LED does not turn solid blue, try Method 1.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device is restricted to be used in the indoor.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
Contact
Shenzhen Renqing Excellent Investment Co., Ltd.
Address: 3/F, Block A7, Nanshan iPark, No.1001 Xueyuan Road, Nanshan District, Shenzhen, China
Email: techsupport@rockspace.cc
Please go to this website to download specific using instructions: http://rockspace.hk/en/news-details.aspx?id=12
