V-TAC LED Floodlight with PIR Sensor

Technical Data

Introduction & Warranty

Thank you for choosing and purchasing a V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any other queries, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 5 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would void the warranty. This product is warranted for manufacturing defects only.

Warranty Period: 5 Years

Features: SAMSUNG LED, V-TAC PRO

Warnings

• Please make sure to turn off the power before starting the installation.
• Installation must be performed by a qualified electrician.
• The light source of this luminaire is not replaceable; when the light source reaches its end of life, the whole luminaire shall be replaced.
• If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
• Proper grounding should be ensured throughout the installation.
• Replace any cracked protective shield.
• Minimum distance from lighted objects: 1m.
• Note: Avoid installing the light near air temperature zones such as air condition, central heating etc.
• This marking indicates that this product should not be disposed of with other household wastes. [Recycling Symbol]

Installation Diagram

The installation process involves several steps, illustrated in diagrams:

• Step 1: Switch off the power. [Power Off Symbol]
• Step 2: Switch on the power and wait for 10 seconds. This action enters the induction mode. [Power On Symbol, Timer Icon]
• Step 3: Switch on the power within 2 seconds. This action enters the constant bright mode. [Power On Symbol, 2 Seconds Indicator]
• Step 4: The floodlight will flash, confirming the change to constant bright mode. [Flashing Light Symbol]

Mode Change Instructions:

• To change from induction mode to constant bright mode: Switch off the power, wait for 10 seconds, then switch the power back on.
• To change from constant bright mode to induction mode: Switch off the power, then switch the power back on within 2 seconds.

Installation Instructions

• DO NOT USE IN AREAS WITH LIMITED VENTILATION OR OUTSIDE THE RATED AMBIENT TEMPERATURE RANGE.
• CONNECT WITH WATERPROOF CABLE HOUSE ONLY.
• ENSURE ELECTRICITY IS SWITCHED OFF BEFORE INSTALLATION.
• Please do not mount to a surface that is prone to vibrations.
• Remove the screw that mounts the bracket for the fixture. Remove the bracket.
• Mark the hole position for fixing the bracket onto the wall. Drill onto the wall at the marked positions (screws not supplied).
• Mount the bracket back to the fixture. Adjust the floodlight to the desired position and tighten the screw of the fixing bracket.
• Connect your mains cable with the input lead of our product through a waterproof junction box (not included).
• Switch on the power and test if the light is working properly.
• Adjust the irradiation angle according to the condition of usage.

Function

LUX Setting

This setting determines the ambient light level at which the sensor operates. The consumer can adjust the work ambient light. When adjusted to the "sun" position (maximum), it can work during the daytime and at night. When adjusted to the "moon" position (minimum), it works only when the ambient light is less than 5LUX. Refer to the testing pattern for detailed adjustment.

SENS Adjustable

This knob adjusts the sensitivity of the motion sensor. Set the SENS knob to "-" for low sensitivity (detection distance of 2m). Set the knob to "+" for high sensitivity (detection distance of 8m).

Time-Delay

This feature is adjustable and allows the light to remain on after motion is detected. When the sensor receives subsequent induction signals after the first detection, it will recompute the time delay from that point. The time delay can be set according to the consumer's desire, ranging from a minimum of 12 seconds to a maximum of 6 minutes.

Manual Override

• To override to constant light mode: Ensure the sensor is switched ON in the automatic mode. Turn the wall switch OFF, then switch power ON within 2 seconds. The floodlight will flash, confirming the light has been switched to constant light mode. The sensor will now hold the light ON continuously, similar to a normal light.
• To switch back to automatic mode: Turn your wall switch OFF, then switch it ON again after 10 seconds. The floodlight will flash, confirming the switch back to automatic light mode.

Test

• Set the SENS knob clockwise to the maximum (+).
• Set the TIME knob anti-clockwise to the minimum (-).
• Set the LUX knob clockwise to the maximum (sun position).
• When you switch on the power, the light will turn on immediately. It will then turn off automatically after 5-30 seconds. If the light receives an induction signal during this period, it will work normally.
• After the first detection, the light can work again after a 10-second delay. If there is no induction signal, the load will stop working within 10 seconds.
• Turn the LUX knob anti-clockwise to the minimum setting. If it is adjusted to 5LUX, the load and sensor should not work when testing in daylight. If you cover the detection window with an opaque object, such as a towel, the load will work. Under no induction signal, the load will stop working within 10 seconds.
• Note for testing in daylight: Please turn the LUX knob to the "SUN" position; otherwise, the sensor lamp will not work.
• Ensure there is no hinder or unrest objects affecting the detection in front of the detection window.

Troubleshooting

1. Why does the sensor not switch OFF the light automatically?

• Please check if there is a continuous signal in the detection field.
• Please check if the time delay has been set to maximum.
• Please check if the power corresponds to the instructions.
• Please check if the temperature near the sensor changes, such as from air conditioning or central heating.

2. Why is the sensor sensitivity poor?

• Please check if there is any hinder in front of the detection window.
• Please check if the ambient temperature is too high.
• Please check if the induction signal source is within the detection field.
• Please check if the installation height corresponds to the installation height mentioned in the instructions.

Contact Information

For any query or issue with the product, please reach out to us at: SUPPORT@V-TAC.EU

For more products range and inquiries, please contact our distributor or nearest dealers.

V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B