Hover-1 Beast Electric Scooter Operation Manual

Introduction

The Hover-1 Beast is a personal transporter. Its technology and production processes are developed with strict testing for each Beast scooter. Operating the Beast without following the contents of this manual may lead to damage to your Beast, or bodily injury. This manual is designed to provide the information needed for the safe operation and maintenance of your Beast. Please read it thoroughly before riding.

Package Contents

• Hover-1 Beast Electric Scooter
• 3-pin Charge Cable
• Operation Manual

Features/Parts

Operating Principals

The device uses digital electronic gyroscopes and acceleration sensors to control balance and motion, depending on the user's center of gravity. The device also uses a control system to drive the motors located within the wheels. It has a built-in inertia dynamic stabilization system that assists with balance when moving forward and backward, but not while turning.

TIP: To increase stability, shift weight to overcome centrifugal force during turns, especially at higher speeds.

Specifications

Controls and Display

Turning Your Device On/Off

Power On: Take your device out of the box and place it flat on the floor. Press the power button (located on the rear of your device) once. Check the LED indicator (located in the center of your device). The battery indicator light should be lit, indicating the device is powered on.

Power Off: Press the power button once.

This model also has a self-balance function. Generally, the device will activate the self-balance function when powered on. If it doesn't activate, press the power button twice while the scooter is on.

Mat Sensor

There are four sensors under the foot mats. When the user steps off the scooter mats, it will automatically initiate self-calibration. When riding, ensure you are stepping on the foot mats. Do not step or stand on any other area. The Beast may vibrate or spin if weight and pressure are applied to only one foot mat.

Battery Indicator

The display board is located in the middle of the Beast.

• Green LED light: Hoverboard is fully charged.
• Red flashing LED light and beeping: Low battery.
• Yellow light: Board is charging.

When the LED light turns red, please recharge the device.

Running Indicator

When the operator triggers the foot mats, the Running Indicator LED will light up, indicating the system enters the running state. If the system has an error, the running LED light will turn red (see SAFETY ALERTS for more details).

Bluetooth Speaker

The Beast has powerful built-in wireless speakers for playing music while riding.

Pairing the Speaker

1. Turn on your Beast; the speakers will “Ping” to announce Bluetooth® pairing mode.
2. Place the Beast and the Bluetooth® device within operating distance (recommend within 3 feet).
3. Ensure Bluetooth® is enabled on your phone or music device. Refer to the manufacturer's instructions.
4. On your device, select "HY-BEAST" from the list of available Bluetooth® devices.
5. If required, enter the PIN code "000000" and confirm.
6. The Beast will say "Paired” when successfully paired.
7. Pairing mode lasts for two minutes. If no devices are paired, the speaker returns to standby mode.
8. If pairing is unsuccessful, turn off the Beast and re-pair.
9. If your smartphone is out of range or the Beast's battery is low, the speaker may disconnect. The Beast will say "Disconnected." To reconnect, follow the aforementioned steps or recharge your scooter.

NOTE: Once paired, the speaker remembers the device and will pair automatically when the device's Bluetooth® is activated and in range. Re-pairing is not needed for previously connected devices. Your scooter can pair up to two multi-point devices.

Listening to Music

Once paired, stream music wirelessly. Only one speaker plays music; the other is for safety alerts. Select tracks on your device. All volume and track controls are managed via your music device. Refer to your device's user manual for streaming issues.

Smart Phone App

Your Beast is an App-enabled scooter compatible with Apple iOS and Android devices. Download the free Hover-1 App to access features like GPS and skill mode. Use a QR code reader to scan the codes below to download the Hover-1 App. You can also search "Hover-1" in your device's App store.

Before Riding

It is important to fully understand all elements of your Beast. Incorrect use may result in loss of control. Learn the functions of the various mechanisms before riding. Practice at slower speeds in a flat, open area before riding in public areas.

Pre-Ride Checklist

Ensure your Beast is in proper working order each time you ride. If a part is not functioning correctly, contact Customer Support.

• Ensure the battery is fully charged before riding.
• Wear appropriate safety and protective gear as mentioned in the User Manual.
• Wear comfortable clothes and flat closed-toe shoes.
• Carefully read the User Manual for basic working principles and tips.

Safety Precautions

Different localities and countries have laws governing riding on public roads. Check with local officials to ensure compliance.

Hover-1 is not liable for tickets or violations for not following local laws and regulations.

• For safety, always wear a helmet that meets CPSC or CE safety standards. A helmet can protect from serious injury or death in an accident.
• Obey all local traffic laws: lights, one-way streets, stop signs, pedestrian crosswalks, etc.
• Ride with traffic, not against it.
• Ride defensively; expect the unexpected.
• Give pedestrians the right-of-way.
• Do not ride too close to pedestrians; alert them if passing from behind.
• Slow down at intersections and look left and right before crossing.

Your Beast is not equipped with reflectors. Riding in low visibility conditions is not recommended.

Think about safety when riding to prevent accidents. Below is a helpful checklist for riders.

Safety Checklist

• Do not ride above your skill level. Practice all functions and features.
• Before stepping on, ensure the Beast is flat on level ground, power is on, and the Running Indicator light is green. Do not step on if the Running Indicator light is red.
• Do not attempt to open or modify your Beast, as this voids the warranty and may cause failure, resulting in injury or death.
• Do not use the Beast in a manner that endangers people or property.
• When riding near others, maintain a safe distance to avoid collision.
• Keep feet on the pedals at all times. Moving feet off the Beast while driving is dangerous and may cause it to stop or veer sideways.
• Do not operate the Beast under the influence of drugs and/or alcohol.
• Do not operate the Beast when restless or sleepy.
• Do not ride off curbs, ramps, or in skate parks, empty pools, or similar areas. The Beast IS NOT A SKATEBOARD. Misuse voids the warranty and may lead to injury or damage.
• Do not continuously spin in place; it causes dizziness and increases injury risk.
• Do not abuse your Beast; doing so can damage the unit and cause system failure, leading to injury. Physical abuse, including dropping, voids the warranty.
• This device is recommended for riders aged 15 and older.
• At higher speeds, consider longer stopping distances.
• Do not step forward off your Beast.
• Do not attempt to jump on or off your Beast.
• Do not attempt stunts or tricks.
• Do not ride in dark or poorly lit areas.
• Do not ride off-road, near potholes, cracks, or uneven surfaces.
• You are 4.5 inches (11.43 cm) taller when operating the Beast. Ensure safe passage through doorways.
• Do not turn sharply, especially at high speeds.
• Do not step on the fenders.
• Avoid driving in unsafe places with flammable gas, steam, liquid, dust, or fiber, which could cause fire and explosion.
• Before riding, ensure tires are in good condition with sufficient tread.
• Do not operate near swimming pools or other bodies of water.

Riding Your Beast

Before using, familiarize yourself with operating procedures.

Operating Your Device

Ensure the device is fully charged before initial use. For charging instructions, see "CHARGING YOUR BEAST".

Stand directly behind your device and place one foot on the foot mat. Keep weight on the foot on the ground; otherwise, the device may move or vibrate, making it difficult to step on evenly with the other foot. When ready, shift weight to the foot on the device and step on with the second foot quickly and evenly.

Find your center of gravity. With weight distributed correctly and center of gravity level, you should be able to stand as if on the ground. It takes about 3-5 minutes to get comfortable standing and maintaining balance. A spotter can help you feel more secure. The Beast is intuitive and senses slight motion; anxiety or reservation can cause panic and unwanted movement.

To move, focus on your desired direction. Thinking about where you want to go shifts your center of gravity, propelling you. Your center of gravity determines movement, acceleration, deceleration, and stopping. Tilt your center of gravity in the direction you wish to move.

To turn, focus on the direction and stay relaxed.

As you become comfortable, maneuvering becomes easier. At higher speeds, shift weight to overcome centrifugal force. Bend knees for bumps or uneven surfaces, then dismount and carry the Beast to a safe operating surface.

Dismounting Your Device

Dismounting can be easy but incorrect dismounting may cause falls. From a stopped position, lift one leg and place it back on the ground (STEPPING BACK). Then step off completely.

Weight and Speed Limitations

Speed and weight limits are for your safety. Do not exceed these limits:

• Maximum Weight: 330 lbs
• Minimum Weight: 44 lbs
• Maximum Speed: Up to 7.45 mph

Operating Range

The Beast can travel up to 8.4 miles on a full charge in ideal conditions. Factors affecting operating range include:

• Terrain: Riding distance is highest on smooth, flat surfaces. Uphill or rough terrain reduces distance.
• Weight: Lighter users have further range than heavier users.
• Ambient temperature: Ride and store the device under recommended temperatures for increased driving distance, battery life, and performance.
• Speed and Riding Style: Moderate, consistent speed maximizes distance. High speeds, frequent starts/stops, idling, and frequent acceleration/deceleration decrease distance.

Balance & Calibration

If your Beast is unbalanced, vibrating, or not turning properly, calibrate it using these steps:

1. Place the Beast on a flat, horizontal surface. Foot mats should be even and not tilted. Ensure the charger is unplugged and the board is off.
2. Press and hold the ON/OFF button for 15 seconds. The scooter will turn on, lighting the battery indicator.
3. Turn the board off, then turn it back on. Press the power button twice. Calibration is complete.

Safety Alerts

If there is a system error or illegal operation, the device will alert the user. The Running Indicator Light will turn RED, and a beep sound will alert you to take precaution and cease operation, potentially causing the device to stop suddenly.

These alerts should not be ignored. Take appropriate action to correct any illegal operation, failure, or errors.

• Unsafe riding surfaces (uneven, too steep, unsafe, etc.).
• Platform tilted more than 17 degrees forward or backward when stepping on.
• Battery voltage is too low.
• Device is still charging.
• Platform self-tilts due to excess speed during operation.
• Overheating or motor temperature is too high.
• Device has been rocking back and forth for over 30 seconds.
• If the system enters protection mode, the alarm indicator lights up and the board vibrates (usually when the battery is low).
• If the platform is tilted forward or backward more than 17 degrees, the Beast will power off and stop suddenly, possibly causing the rider to lose balance or fall off.
• If any or both tires are blocked, the device stops after 2 seconds.
• When battery level depletes below protection mode, the device engine powers off and stops after 15 seconds.
• While sustaining high discharge current (e.g., driving up a steep slope for a long period), the device engine powers off and stops after 15 seconds.

Charging Your Beast

Charging the Device

• Ensure the charging port is clean and dry. No dust, debris, or dirt inside the port.
• Plug the charger into a grounded wall outlet. The charging indicator light ON THE CHARGER will be green.
• Connect the cable with the power supply (100V ~ 240V; 50/60 Hz).
• Align and connect the 3-pin charging cable into the charging port. DO NOT FORCE OR BEND THE CHARGING CABLE INTO THE CHARGING PORT, AS IT MAY CAUSE THE PRONGS TO BEND OR BREAK.
• Once attached, the charging indicator light ON THE CHARGER should change to RED, indicating charging.
• When the RED indicator light turns GREEN, the device is fully charged.
• A full charge may take up to 3.5 hours. A flashing yellow light on the scooter also indicates charging. Do not charge for more than 4 hours.
• After fully charging, unplug the charger from the device and the power outlet.

Battery Care / Maintenance

Battery Specifications

• Battery Type: Rechargeable lithium-ion battery
• Charge Time: Up to 3.5 hours
• Voltage: 36V
• Initial Capacity: 4.0 AH

Battery Maintenance

The lithium-ion battery is built-in. Do not disassemble the device to remove or separate the battery.

• When charging, use the enclosed 3-pin charging cable or ensure battery charging conditions are met.
• Do not connect or attach the device or battery to a power supply plug or car's cigarette lighter.
• Do not place the device or batteries near fire or direct sunlight. Heating can cause additional heating, breaking, or ignition.
• Do not continue charging if it does not recharge within the specified time, as this may cause the battery to become hot, rupture, or ignite.

To preserve natural resources, recycle or dispose of batteries properly. This product contains lithium-ion batteries. Local, state, or federal laws may prohibit disposal in ordinary trash. Consult your local waste authority for recycling/disposal options.

• Do not attempt to modify, change, or replace your battery.
• Do not use if the battery emits odor, overheats, or leaks.
• Do not touch leaking materials or breathe fumes.
• Do not allow children and animals to touch the battery.
• The battery contains dangerous substances; do not open or insert anything into it.
• Use only the charger provided by Hover-1.
• Do not attempt to charge if the battery has discharged or emits substances. Immediately distance yourself from the battery in case of fire or explosion.
• Lithium-ion batteries are hazardous materials. Follow all local, state, and federal laws for recycling, handling, and disposing of them.

Care & Maintenance

• Do not expose the device to liquid, moisture, or humidity to avoid damage to internal circuitry.
• Do not use abrasive cleaning solvents.
• Do not expose the device to extreme temperatures, as this shortens electronic device life, destroys the battery, and/or distorts plastic parts.
• Do not dispose of the device in fire; it may explode or combust.
• Do not expose the device to sharp objects, as this will cause scratches and damage.
• Do not allow the device to fall from high places, as this may damage internal circuitry.
• Do not attempt to disassemble the device.
• Use only the charger provided by Hover-1.

Warranty

For warranty information, please visit: www.hover-1.com

Affix Serial Number Label Here:

Design

The Hover-1 Beast is designed for easy control, providing a safe, stable form of travel. With a zero-degree turning radius, it can be operated in narrow spaces without moving forward. Built-in sensors are responsive with a balancing system. Acceleration and deceleration are controlled by applying pressure with feet or leaning. Two drive motors are controlled independently or by both feet for turns, rotations, and smooth braking. The Beast requires approximately 3.5 hours of charging for a full charge.

Performance

The Hover-1 Beast is a two-wheel balancing electric scooter, offering convenient, stable transportation. It is responsive to weight and angles, making it easier and safer to control, allowing travel up to 8.4 miles at speeds up to 7.45 mph.

• Travel up to 8.4 miles
• Maximum speed of up to 7.45 mph
• Supports up to 330 lbs
• Fully charges in up to 3.5 hours