Reizen Atomic Talking Analog Alarm Clock

Product Overview

Congratulations on your purchase of the Reizen Atomic Talking Analog Alarm Clock. This clock combines traditional analog styling with modern features, including time and date announcements and the convenience of atomic radio-controlled time setting, which automatically synchronizes the time daily. Additional features include an easy-to-set alarm with two large buttons, adjustable volume control (High, Medium, Low, Off), and a soft LED backlight.

Button Identification

The clock features several buttons and switches for its various functions. Refer to the diagrams for visual placement:

• S1 (Talking + Snooze + Lamp): Located on the top of the clock.
• S2 (Alarm Hour): Located on the front left side.
• S3 (Alarm Minute): Located on the front right side.
• S4 (Alarm Volume + Off): Located on the right side of the clock.
• S5 (Wave): Located on the back, used for manual signal reception.
• S6 (Reset): Located on the back, used for resetting the clock.
• S7 (Time Zone: P,M,C,E): Located on the back, used for setting the US Time Zone.
• S8 (DST On/Off): Located on the back, used for setting Daylight Saving Time.
• S9 (Advance Hour): Located on the back, used for manual time setting (hour).
• S10 (Advance Minute): Located on the back, used for manual time setting (minute).

Automatic Time Setting

The Reizen Atomic Talking Analog Alarm Clock automatically adjusts to the precise correct time via a radio signal received daily at 3:00 AM from the US Atomic Clock. After signal reception, the clock will display the correct time on both the analog face and in talking mode. The clock also automatically accounts for Daylight Saving Time (DST), though this can be turned off. Manual setting is available for travel or locations without a reliable atomic radio signal.

Button Functions

Time Announcement

Push S1 once to hear the current Hour and Minute.

Day & Date Announcement

Push S1 twice to hear the Day, Month, Date, and Year.

Reception Status Check

1. Push S1 three times to hear the reception status of the clock.
2. If the reception was successful, the clock will announce "Country Name" followed by "Time Updated" (e.g., "USA, Time Updated").
3. If the reception failed, the clock will announce "Country Name" followed by "Time Not Updated" (e.g., "USA, Time Not Updated").

Alarm Time Announcement

Press S2 or S3 once to check the current Alarm Time Setting while the second hand is running normally. The clock will announce the current alarm set time.

US Time Zone Setting

To set the US Time Zone, open the battery cover to access the Time Zone Setting button (S7). Press S7 once to hear the current setting (preset to Pacific Time). Continue pressing S7 until your desired US Time Zone is announced (US Pacific, US Mountain, US Central, or US Eastern). Press S1 to confirm, or the clock will confirm automatically after one minute. The second hand will run fast to set the new time.

Daylight Savings Time (DST) On/Off Setting

Press and hold S8 down to set DST to OFF. Release the button to set DST to ON. Refer to the markings on the clock for guidance.

Manual Signal Reception

While the clock is in Time Keeping mode, press S5 (Wave) once to initiate manual signal reception. The second hand will stop at the 12 o'clock position during reception, and the minute hand advances one step every 60 seconds. Signal reception typically takes 5 to 14 minutes. After reception, the clock will display the time. To check if reception was successful, push S1 three times. If successful, it will announce "Country Name" followed by "Time Updated". If failed, it will announce "Country Name" followed by "Time Not Updated". For best reception, place the clock on a table near a window. If reception fails, try a different location or repeat the steps. If repeated attempts fail, the radio signal may not be strong enough in your area, and manual time setting may be necessary.

Setting Daily Alarm

The alarm is set using the two large buttons on the front of the clock. Settings are announced audibly, aiding accuracy and usability for the visually impaired.

Set Daily Alarm Hour

1. Press S2 twice to hear the current Alarm Hour.
2. Continue pressing S2 until the desired new Alarm Hour is reached, carefully noting the AM/PM setting.

Set Daily Alarm Minute

1. Press S3 twice to hear the current Alarm Minute.
2. Continue pressing S3 until the desired new Alarm Minute is reached.

Press S1 to confirm the new Alarm Time setting, or the clock will confirm itself one minute later, announcing the set time.

Snooze Alarm

1. When the alarm is beeping, press S1 once to set the clock to Snooze mode.
2. The alarm will beep again after 5 minutes.
3. The Snooze function can be used up to 5 times.

Turning Off Alarm Sound

You can turn off the alarm sound (without snoozing) by holding down the S1 button until the clock announces the current time. The alarm is a daily alarm. To leave the alarm set but prevent it from sounding, slide the S4 button to the "Off" position.

Alarm ON/OFF

1. Hold S5 (Wave) down until the clock announces the alarm status ("Alarm is On" or "Alarm is Off").
2. Release the button.
3. Press S5 (Wave) again to change the setting from On to Off, or Off to On.
4. Press S1 (the top button) once to confirm, or the status will be confirmed after one minute.

Alarm Volume Setting

Slide S4 to set the volume of the talking clock.

Turn the Clock to Silence

Slide S4 to the OFF (bottom) position to silence the clock.

Manual Time Setting (for Country without Time Signal)

Use this function when traveling or in locations with no radio time signal. Press S9 to set the Hour and S10 to set the Minute manually. Listen carefully to ensure the correct AM or PM time is selected. Press S1 to confirm the time, or the clock will confirm itself one minute later. After confirmation, the clock will automatically run to the new time. Note: The Date, Day, Month, and Year cannot be manually set on this clock.

Backlight

The backlight is switched ON when the S1 button is pressed.

Troubleshooting

General Issues

Your clock is a delicate and precise instrument. Although uncommon, hard knocks or vibrations can cause the hands to move irregularly, displaying the incorrect time, even if the internal clock is keeping accurate time. If you notice the clock receives a signal and announces the correct time but the hands are not synchronized, the clock needs to be reset. Please refer to the "Reset the Clock" section for details.

Reset the Clock

1. Press S6 (Reset) with a ballpoint pen to reset the clock.
2. The clock will align the hands to 12 o'clock automatically and then perform a signal reception.
3. Place the clock in a location where signal reception is possible after the reset.
4. The correct time will display after a signal is received. This may take up to 24 hours, depending on your location and the time of reset.
5. US users must set the correct Time Zone after the clock is able to pick up a signal. Refer to the "US Time Zone Setting" section for details.

Clock Not Receiving Time Signal

Reasons for not being able to receive the Time Signal include:

• Being outside of the US signal area.
• Being in a built-up area (e.g., apartment buildings).
• Metal objects blocking the radio signal.
• Interference by a computer or TV monitor.

If your clock is unable to make contact with the radio signal, it will continue to function as a standard clock. The time will be corrected the next time your clock receives the time signal.

Clock Stops and No Talking Function

When the battery is low, the clock hands will stop, and the talking function will be terminated. It is time to change the batteries. Please refer to the "Battery Change" section for details.

Hour, Minute and/or Second Hand(s) is Not Correct

You need to reset the clock. Refer to "Reset the Clock" for details.

Hands Running Non-Stop After Battery Replacement

Press the Reset button (S6).

The Clock Does Not Run After Battery Replacement

Press the Reset button (S6).

Low Battery Detection

When the battery is low, the second hand slows to one step every 2 seconds, and the talking function is terminated. Both batteries should be replaced. Refer to the "Battery Replacement" section for details.

Battery Replacement

This clock uses 2 "C" batteries. Alkaline batteries are recommended.

1. Open and carefully remove the battery cover.
2. Remove the old batteries and insert 2 new batteries with the correct polarity.
3. Press the S6 (Reset) button after battery replacement.
4. Place the clock in a location where signal reception is possible and wait until the clock sets itself automatically. This will take from 1 to 24 hours.
5. Set your US Time Zone as necessary after the clock picks up the signal. Refer to the "US Time Zone Setting" section for details.

Limited 90-Day Warranty

This item is covered under manufacturer's warranty for a period of 90 days from the purchase date. This warranty does not cover damage due to abuse, misuse, water damage, or if the unit is dropped.

Manufacturer Information

REIZEN, INC.

P.O. Box 3312

Farmingdale, NY 11735

Phone: 631-752-0521

Website: www.ReizenUSA.com