7 ALARMS
1. Press the [Left Button] and release. The "alarm 1" symbol will start blinking. Set the alarm hour using the [Middle Button] and the minute using the [Right Button].
Image Description: The display shows the current time (e.g., 09:34) and day (e.g., Fri), with the "alarm 1" symbol blinking. Buttons are labeled ALARM SET, HOUR, and MINUTE.
To cancel an alarm, press the [Center Button] until a cancellation indicator appears on the screen.
2. Once the correct alarm time is set, press the [Left Button] to move to the next alarm.
3. Once the "alarm 2" symbol is blinking, set this alarm in the same way.
4. Continue setting alarms 3 through 6 in this manner.
5. Finish by pressing the [Left Button] until the alarm symbols are no longer blinking.
Hold the [Center Button] or [Right Button] to automatically progress through hours or minutes as desired. The display will return to normal function if left idle for more than one minute.
8 TONE OPTIONS
Choose between alarm tones A, B, or C. Your selection will be displayed on the screen. Silent alarms will show no choice. To change the tone, hold down the [Right Button] while pressing the [Left Button] to cycle through the available tones.
Image Description: The display shows options for alarm tones A, B, or C.
Release both buttons once your desired alarm tone is displayed.
9 TEST
To enter test mode, hold the [Center Button] until "CH" appears on the screen. To exit test mode, press the [Right Button].
To perform tests, press the [Left Button]. The unit will cycle through the following test modes:
- CH1: All segments on the display will light up.
- CH2: The motor rotates the tray by one compartment.
- CH3: The alarm will sound and LED lights will illuminate.
Following the CH3 test, turn the dispenser over to test the "RESET" function. The alarm and LED should stop. If they do not stop within 10 seconds, "CH4" will be displayed on the screen.
NOTE: If the dispenser does not rotate properly, an error message "CH6" will appear on the screen. If this occurs, press the [Right Button] and replace the batteries to reset the unit.
10 LOCKING & UNLOCKING
Insert the key ? and turn it 1¼ turns to the right ➡️ to unlock, or 1½ turns to the left ⬅️ to lock.
Image Description: Shows a key being inserted into the lock mechanism and turned to either lock or unlock the dispenser.
11 STOP ALARM
When the alarm sounds, pick up the dispenser and tilt the pills into your hand or a suitable container.
Image Description: Illustrates tilting the pill dispenser to dispense the medication into a hand or container.
12 STANDBY/LOW BATTERY
When not in use, the display will shut off, and the dispenser enters "Standby Mode." To wake it up, press the [Right Button].
When batteries are low, a battery symbol with an "X" through it (?❌) will appear on the screen. When you see this symbol, the batteries are low and need to be replaced.
Image Description: Shows the low battery indicator symbol (a battery with an X through it) on the dispenser's screen.
1 TO START
Place 4 AA batteries into the battery compartment.
Image Description: The back of the pill dispenser is shown with the battery compartment open, indicating the placement of four AA batteries.
2 OPENING THE TRAY
Push on the front tab with your thumb as shown.
Image Description: A finger is shown pushing a tab located on the front of the dispenser to open the medication tray.
3 CLEANING
Surface clean the dispenser using only a damp sponge or cloth. Remove the tray before cleaning.
PLEASE NOTE: Do not place the product in direct sunlight or expose it to strong ultraviolet light to avoid malfunction.
Image Description: The dispenser is shown being cleaned with a damp cloth.
4 FILLING DISPENSER
The dispenser includes 6 discs, each labeled with a day of the week and the number of doses to be taken each day (from 1 to 6 times).
The dose options are:
- 1. Once a day
- 2. Twice a day
- 3. Three times a day
- 4. Four times a day
- 5. Five times a day
- 6. Six times a day
Organize your medications and assign dose times yourself, with a caregiver, or with the help of a healthcare professional.
Depending on how many doses of medication you take per day, you may need to refill your dispenser more quickly:
- 1x/day: refill approximately every 28 days
- 2x/day: refill approximately every 14 days
- 3x/day: refill approximately every 9 days
- 4x/day: refill approximately every 7 days
- 5x/day: refill approximately every 5 days
- 6x/day: refill approximately every 4 days
Image Description: Six circular discs are shown, labeled 1x, 2x, 3x, 4x, 5x, and 6x, representing the number of daily doses.
With the clear plastic tray removed, place the desired disc around the central hub and fold down the tabs to secure it.
Image Description: A disc is shown being placed onto the central hub of the dispenser tray, with tabs being folded down to hold it in place.
Then, return the clear plastic tray back into place.
5 CHANGING TIME FORMAT
The dispenser defaults to a 24-hour time format. To switch to a 12-hour format, press buttons 2 and 3 simultaneously until an AM or PM symbol appears on the right side of the display.
Image Description: The dispenser's screen is shown displaying the time, with an indicator for AM or PM on the right side.
When your preferred time format is displayed, release the buttons.
6 SETTING THE TIME
1. Press and hold the [Left Button] until the colon ":" starts blinking, then release the button.
2. Set the hour using the [Middle Button]. Set the minutes using the [Right Button].
Image Description: The display shows the time (e.g., 09:34), with labels indicating HOUR and MINUTE for setting.
3. Confirm the time by pressing the [Left Button] again.
Image Description: The display shows the confirmed time (e.g., 09:34).
