Required Tools

Drill with 1/4" nut driver

Important Warning

⚠️ WARNING: If the information in these instructions is not followed exactly in conjunction with the installation manual for the fireplace, a fire or explosion may result, causing property damage, personal injury, or loss of life.

REV A | 85-03-01251

Installing Into the Firebox

Follow these steps to install the LED Component Kit into the firebox:

1. If the burner is currently installed, start by removing the burner from the firebox along with any media and glass that may be installed.
2. Remove the bracket that the junction box is secured to by removing the two screws holding it to the firebox.
3. Remove the junction box from the bracket by removing the cover plate and then removing the two screws securing it to the bracket.
4. Reattach the junction box to the LED Component Kit bracket in the same location and orientation.
5. Install the LED Component Kit in the same location and orientation as the original bracket that was removed.

[Diagram: Visual representation of installing the LED Component kit to the firebox, showing the placement of the kit and junction box.]

Wiring LED Controller

Note: There are two LED Controllers available, allowing the optional LED Floor Kit and LED Glass Barrier to be controlled independently.

The power supply leads can be wired into the junction box with the house power and unit power wires.

[Diagram: Image showing the wiring connections. Labels indicate "To house power", "To LED Floor", and "To LED Glass Barrier". The image displays the power supply, junction box, and connecting wires.]

Reconnecting Components

Follow the individual component installation instructions for connecting the LED component kits, such as the LED Floor Kit and the LED Glass Barrier. The remote comes pre-paired to the controllers; you only need to connect the LED kits to the LED controller leads.

Resyncing Controllers to Remote

Note: The instructions below are for resyncing the controllers to the remote.

If you are installing both the LED Floor Kit and the LED Glass Barrier, you have two options for connecting components to the LED controllers:

• Option A: Connect both kits to one controller. Both the LED floor and LED Glass barrier will always be the same color.
• Option B: Connect each kit to its own controller, allowing them to be color-controlled independently.

Resyncing Procedure:

1. Turn off the rocker switches for both LED controllers. Status indicator lights are visible through the floor access; if no light is visible, the LED controller is powered off.
2. Restore power to the LED controller you wish to connect to a component by turning its corresponding rocker switch ON. Within 3 seconds of restoring power, press the "I" (ON) button for Zone 1 control. If pairing is successful, the status indicator lights will blink green 3 times slowly on the firebox floor access for the selected controller.
3. If you are not using the second controller, leave its rocker switch in the OFF position.
4. If you are using the second LED controller, restore power to it by turning its corresponding rocker switch ON. Within 3 seconds of restoring power, press the "I" (ON) button for Zone 2 control. If pairing is successful, the status indicator lights will blink green 3 times slowly on the firebox floor for the selected controller.

[Diagram: Image showing the LED component with status indicator and SYNC button access holes. Also shows rocker switches.]

[Diagram: Image of the Mi-Light remote control with labels for Link/Unlink button, Zone Selections (1, 2, 3, 4), and other controls (S-, S+, M).]

Installation Completion

The LED Component Kit installation is now complete. Replace all components that were removed to gain access, in the reverse order of removal.

Refer to the next page for quick setup instructions for the LED remote and smartphone connection. To control the LED lights with your smartphone, Google Home, or Amazon Alexa, proceed to the LED controller instructions. Complete instructions for the remote and controller are also provided in the kit if more information is necessary.

Mi-Light RGBW Remote Controls

This section describes two types of RGBW remote controls used with Mi-Light products: the FUT095 (buttons) and FUT096 (touch screen).

Product Features

Both remote controls share the same functions but differ in design. Each remote can control LED lights across up to four different zones, change colors, adjust brightness/dimming, set warm/cool white, and activate various programs.

Technical Parameters

FUT095 RGBW Remote Control with Buttons

• Product Name: RGBW remote control with buttons
• Model No.: FUT095
• Voltage: 3V (2 x AAA Batteries)
• Transmission Frequency: 2.4GHz
• Modulation Method: GFSK
• Transmitting Power: 6dBm
• Standby Power Consumption: 20uA
• Control Distance: 30m
• Size: 52.5mm x 21mm x 120mm

FUT096 Touch Screen RGBW Remote Control

• Product Name: Touch screen RGBW remote control
• Model No.: FUT096
• Voltage: 3V (2 x AAA Batteries)
• Transmission Frequency: 2.4GHz
• Modulation Method: GFSK
• Transmitting Power: 6dBm
• Standby Power Consumption: 20uA
• Control Distance: 30m
• Size: 52.5mm x 21mm x 120mm

[Diagram: Side view of the remote control showing dimensions (52.5mm, 21mm, 120mm).]

Products Key Diagram (FUT096 Example)

Remark:

• Hold "I" (Master ON) to get white mode.
• Under white mode: press 'S-' for warm white, press 'S+' for cool white.
• Under color mode: press 'S+' or 'S-' for saturation control.
• When 'M' (Mode) is pressed, 'S+' or 'S-' can adjust the speed of dynamic modes.

To dim all RGBW lights at once or change the color, first press "Master ON". To do this with individual lights, first press "Zone ON", then choose the color or brightness according to the color ring or brightness ring.

[Diagram: Layout of the FUT096 touch screen remote control. Key elements labeled: Master ON, Color ring, Brightness-, Speed-, Zone ON, Zone OFF, Master OFF, Indicator light, Brightness+, Speed+, Modes(Programs), 4x(un) Link Light, S-, S+, M buttons.]

Linking & Unlinking Mi-Light Remotes

Remark: The light can be operational after linking with the remote controller.

Linking Instructions

1. Switch off the light, then switch it on again after 10 seconds.
2. When the light is ON, short press any zone button ("I") 1 time within 3 seconds.
3. The light will blink 3 times slowly, indicating successful linking.

If the light does not blink slowly, linking failed. Switch off the light again and repeat the steps.

[Diagram: Step-by-step visual guide for linking. Shows power off/on, pressing Link/Unlink button, and successful blink.]

Unlinking Instructions

1. Switch off the light, then switch it on again after 10 seconds.
2. When the light is ON, long press the "I" button within 3 seconds.
3. Unlinking must use the same zone as the linking process.
4. The light will blink 10 times quickly, indicating successful unlinking.

If the light does not blink quickly, unlinking failed. Switch off the light again and repeat the steps.

[Diagram: Step-by-step visual guide for unlinking. Shows power off/on, long pressing Link/Unlink button, and successful blink.]

Grouping of Several Lights

You can add an unlimited number of lights to a zone on the 4-channel remote by linking them to different zones. This allows for flexible creation of different group combinations.

[Diagram: Examples of grouping lights into different zones.]

Remark:

• Users can reprogram freely as needed. One remote can control countless lamps or controllers, but one lamp or controller can only be controlled by a maximum of four remotes.
• Please check battery installation and controller power (fully discharge) when programming after switching off and on.

Attention for Remote Use

• This remote controller only works with specified Mi-Light products; not all Mi-Light series are compatible.
• If the indicator lamp blinks quickly during use, change the battery promptly. Do not use poor quality batteries to avoid leakage that could damage the remote controller.
• Keep your finger off the touch ring when installing batteries to improve sensitivity. Use the remote 3 seconds after batteries are installed. Reinstall batteries if the touch ring is found to have low sensitivity.
• This 2.4GHz remote control system is a precise electronic product. Avoid use in humid, high-temperature, dusty, or high-voltage environments. Store in a dry, indoor environment free from static electricity.
• Do not use the remote controller near wide-range metal or strong electromagnetic wave areas, as this will negatively affect the control distance.

Certifications: CE, ROHS

Manufactured in: China

Manual Instruction: WiFi&BT 5-in-1 LED Strip Controller (Model: WB5)

Please read these instructions carefully before using the controller.

1. Features

The controller uses advanced PWM control technology and has a memory function (light status is retained when turned off). It supports wireless and 4G control via the Tuya Smart Life APP.

• ? 16 Million Colors to choose
• ?️ Color temperature 2700K-6500K
• ? Dim brightness / saturation
• ? Support music rhythm
• ✨ Support scene customization
• ⏰ Timing setting/countdown turn on / off LED light
• ? Bluetooth wireless control
• ? Tap-to-Run & automation
• ? Free screw when connecting to LED strip
• ? WiFi wireless control
• ? Smartphone APP control
• ?️ Support third party voice control (e.g., Amazon Alexa, Google Assistant)
• ? Support remote control (control distance 30m)
• ? Device sharing
• ?‍?‍?‍? Group control
• ? 2.4G wireless transmission technology
• ? Auto-transmitting & Synchronization
• ⚙️ Link/Unlink/Reset Button on the controller

2. Parameters

• Model No.: WB5
• Input Voltage: DC12V-24V (5.5*2.1mm connector)
• Output: 6A/Channel (Total Output Max. 15A)
• Working Temperature: -20°C to 60°C
• Communication Mode: WiFi-IEEE 802.11b/g/n 2.4GHz
• RF: 2.4GHz
• Weight: 65g

[Diagram: Illustration of the WB5 controller with input/output ports labeled. Shows dimensions.]

Smart Link & Unlink to APP

There are 3 methods to Link and Unlink to the Tuya/Smart Life APP:

1. Long press the "SET" button for 3 seconds. The purple indicator light will blink 3 times, and the device will enter Smart Link/Unlink mode.
2. Use a linked remote: long press the linked Zone ON button for 3 seconds. The purple light will blink 3 times, and the device will enter Smart Link and Unlink Mode.
3. Switch the controller ON and OFF 3 times (ON-OFF-ON-OFF-ON) within 10 seconds. The purple light will blink 3 times, and the device will enter Smart Link and Unlink Mode.

Note: A red indicator light always ON means the device is not linked to the APP. A green light always ON means the device is linked to the APP and is controllable.

Switching Output Mode

Short press the "SET" button to switch the output mode. The indicating lamp flickering signifies a successful switch. Different color flickers correspond to different output modes:

• White Light Flickering: Single Color Mode
• Yellow Light Flickering: Dual White Mode
• Red Light Flickering: RGB Mode
• Green Light Flickering: RGBW Mode
• Blue Light Flickering: RGB+CCT Mode (Default Mode)

[Diagram: Table showing output modes and corresponding indicator light colors.]

Indicating Light Instruction

3. Auto-synchronization Function

Different controllers can work synchronously when started at different times, controlled by the same remote, under the same dynamic mode and with the same speed.

[Diagram: Illustration showing multiple controllers synchronizing.]

Remark:

• Indicating Auto-transmitting.
• Controllers will auto-synchronize in the same dynamic modes and within a 30m controlling distance.

4. Auto-transmitting Diagram

One strip controller can transmit signals from the remote control to another controller within 30m. As long as there is a strip controller within 30m, the remote control distance can be limitless.

[Diagram: Illustration demonstrating auto-transmitting signal range between controllers.]

5. Connect to LED Strip

Controller input voltage must match the required voltage of the LED Strips. Input voltage = Output Voltage.

[Diagrams: Various connection diagrams for different LED strip types: CCT LED strip, RGB LED strip, Single Color LED strip, RGBW LED strip, RGB+CCT LED strip. Each diagram shows the WB5 controller and the corresponding LED strip connection.]

6. Remote Controller Compatibility

Compatible with these remote controls (purchased separately). For more details, please read the remote instructions.

[Diagram: Images of compatible Mi-Light remote controls: FUT096, 091, FUT007.]

7. Bluetooth Control Instructions

When the WiFi router is disconnected, you can turn on the Bluetooth of your smartphone and connect directly to the device at a short distance.

Switching Bluetooth Control Steps:

1. Complete the network distribution of the equipment.
2. Power off the router used for network configuration, turn off WiFi on your mobile phone, turn on Bluetooth, and wait for about 3-5 minutes to control.

8. Free Screw when Connecting to LED Strip

[Diagram: Illustration showing a screw connection detail for LED strips, indicating a minimum depth of 0.39 inches / 10mm.]

Tuya Smart Life APP WiFi Control Instructions

1. Download and Install [Tuya Smart] APP or [Smart Life] APP

Search for "Smart Life" in the Apple App Store or Google Play Store, or scan the QR code (QR code excluded as per instructions) to download and install the app. Please click the "Register" button to create an account for first-time use, or log in directly if you already have an account.

2. Connect to Smartphone

1. Connect the controller with a power supply.
2. Confirm the pilot lamp is flashing quickly (2 flashes per second). If the pilot lamp is not flashing quickly, there are two ways to enter this state:
   • Long press the "SET" key until the pilot lamp flashes quickly.
   • Power OFF and ON once, then long press the Zone ON button of a linked remote until the LED strip blinks 3 times (available remote model: LM091).
3. Connect your phone to a 2.4GHz home WiFi network.
4. Open the APP homepage and click the "+" button in the upper right corner. If the pilot lamp is flashing red, the APP will find the new device automatically.
5. Added devices will be displayed on the homepage after successful network configuration.
6. Click the desired device to enter the control interface.

[Diagram: Screenshot of the "Devices to be added" screen in the Smart Life app, showing "New Device" and "Smart Wi-Fi Lighting" options.]

3. APP Control

1. Click "device" or "group" on the homepage to enter the control page, where you can adjust color, saturation, brightness, color temperature, and scenes.
2. Click "Music Sync" to enter music rhythm mode, where the light will change with the rhythm of the music. Note: Music rhythm mode requires the phone screen to remain on this page.
3. Click "More" on the bottom right to access additional settings, including Plan, Schedule, Biorhythm, and Power-on behavior. For detailed settings, refer to the provided link: Tuya Developer Documentation.

[Diagram: Screenshot of the "Smart Wi-Fi Lighting" control interface showing color wheel, brightness slider, and mode selection (Color, White, Scene, Music Sync).]

4. Device Name Editing, Third-Party Control, Device Sharing, Group Control

1. Click the "✏️" icon in the upper right corner of the control page to enter the edit page, where you can modify the device name, icon, etc.
2. Click the icon under "Third-party Control" to view detailed descriptions of third-party integrations (e.g., Alexa, Google Assistant).
3. Click "Share Device" to share the device with family and friends.
4. Click "Create Group" and follow the APP prompts to group devices for simultaneous control.

[Diagram: Screenshot showing "Device Information" options including "Tap-to-Run and Automation", "Third-party Control", "Share Device", etc.]

5. Intelligent Control

1. Click "Smart" at the bottom of the app.
2. Click "+" in the upper right corner to create intelligent controls (automations).
3. In the "Create Smart" page, you can set commands to be executed under specified conditions (e.g., turn on/off lights, change color, brightness, mode). Conditions include: When weather changes, when device status changes, schedule, or manual trigger (Tap-to-Run).

[Diagram: Screenshots illustrating the creation of smart automations, showing "Set a condition" and "Set up task" options with examples like "Launch Tap-to-Run", "When weather changes", "Schedule", and "When device status changes".]

Attention

• Please check if the input voltage of the constant voltage power supply matches the controller, and verify the connection of both the cathode and anode.
• The working voltage is DC12~24V. The controller will be damaged if the voltage is higher than 24V.
• Non-professional users should not dismantle the controller directly, as it may cause fire and electric shock.
• The working temperature is -20°C to 60°C. Do not use the device in direct sunlight, moist, or other high-temperature areas.
• Please do not use the controller around metal areas or high magnetic fields, as this will badly affect the control distance.
• When the device load reaches 15A, the wire diameter must be over 1.5mm².

[Icon: Controller cannot be used in humid areas.] Note: Controller can not be used in humid area.

Certifications: CE, ROHS

Manufactured in: China