Nestera Chicken House Large

House Components

The following components are included in your Nestera Chicken House Large:

• 1. Vent covers
• 2. Right side wall (Vent side)
• 3. Back door handle
• 4. Base brace (Only for Large)
• 5. Upper back wall
• 6. Back door
• 7. Base
• 8. Left hand side wall (Nest box side)
• 9. Roof support
• 10. Front panel
• 11. Side roof retainers
• 12. Front roof retainers
• 13. Large straight door retainer
• 14. Small Straight door retainer
• 15. Large curved door retainer
• 16. Small curved door retainer
• 17. Handle
• 18. Left hand nest box wall
• 19. Nest box divider (Not for Small)
• 20. Right hand nest box wall
• 21. Nest box floor
• 22. Nest box front wall
• 23. Roof
• 24. Nest box side brace
• 25. Nest box front brace
• 26. Nest box roof
• 27. Metal Door
• 28. Perch
• 29. Ramp

Diagram Description: A visual layout shows all 29 numbered components of the Large Chicken House, illustrating their shapes and relative positions before assembly.

Fixing Pack

The following fixings are included:

• Pi Clip: Quantity 57
• Lynch Pin: Quantity 19
• Cord 148cm long: Quantity 1
• 25mm Washer: Quantity 3
• 40mm Screw: Quantity 3
• 30mm Screw: Quantity 5
• 20mm Screw: Quantity 1
• Split Ring: Quantity 1
• Standard Washers: Quantity 11
• Nylock Nut: Quantity 9
• Clevis Pin 25mm: Quantity 2
• Clevis Pin 20mm: Quantity 1
• R-Clip: Quantity 2

Note: Fixings are not to scale.

Diagram Description: Images display each type of fixing: Pi Clip, Lynch Pin, Cord, 25mm Washer, 40mm Screw, 30mm Screw, 20mm Screw, Split Ring, Standard Washers, Nylock Nut, Clevis Pin 25mm, Clevis Pin 20mm, and R-Clip, along with their quantities.

Important Note on Lynch Pins: You only need to lift the ring slightly up from the bar. Lynch Pins are designed to spring closed, so watch your fingers!

Recycled & Recyclable Materials

Nestera products are made from recycled materials whenever possible, and materials suitable for recycling are used when new materials are necessary. The plastic is derived from recycled industrial waste. By choosing Nestera, you help reduce the demand for virgin plastic. The plastic is tough, easy to work like wood, does not splinter, is UV resistant, and is impervious to pollutants and weather. It insulates well and resists chewing, maintaining its appearance and functionality longer than timber. Metal components are stainless steel or rust-resistant alloy. Packaging and literature are also made from recycled materials.

Diagram Description: Shows how to fit a Lynch Pin by lifting the ring and inserting it. Another diagram shows how to fit a Pi Clip.

Assembly Instructions

Step 1: Attach Vent Covers

Fit two Vent Covers to the patterned face of the Right Side Wall. Use one M6x30mm screw, one standard washer, one 25mm washer, and two nylock nuts for each vent. Tighten nuts until vents rotate with gentle pressure, but do not spin freely. The Left Side Wall has vent slots for ventilation.

Diagram Description: Illustrates attaching vent covers to the right side wall using screws, washers, and nuts. Arrows indicate the assembly direction.

Step 2: Attach Straight Door Retainers

Fit the Small and Large Straight Door Retainers to the smooth (inside) side of the Front Wall using three 40mm Screws, three Standard Washers, and three Nylock Nuts. These form a recess for the door.

Diagram Description: Shows the front wall with straight door retainers being attached using screws, washers, and nuts.

Step 3: Attach Curved Door Retainers

Fit the Small and Large Curved Door Retainers to the smooth (inside) side of the Front Wall using three 30mm Screws, three Standard Washers, and three Nylock Nuts. These pieces form a recess into which the door fits when closed.

Diagram Description: Shows the front wall with curved door retainers being attached using screws, washers, and nuts.

Step 4: Secure Metal Door Clevis Pin

Insert the Small Clevis Pin into the hole in the Metal Door from behind. Secure it using a washer and split ring. A flat-bladed screwdriver can help open the split ring.

Diagram Description: Depicts inserting a clevis pin into the metal door from behind and securing it with a washer and split ring. A note advises caution with fingers.

Step 5: Fix Metal Door

Place the Metal Door in position and secure it with one 20mm screw, two Standard Washers, one 25mm Washer, and one Nylock Nut. Tighten the Nylock Nut until the door can just rotate freely.

Diagram Description: Shows the metal door being fitted into place and secured with a screw, washers, and a nylock nut.

Step 6: Attach Nest Box Side Wall

Fit the nest box Side Wall to the Base Brace and Base using four Pi Clips. Ensure the double-hole lugs are at the front. Note: The base should be fitted smooth side up.

Diagram Description: Illustrates attaching the nest box side wall to the base and base brace using Pi Clips, with arrows indicating the orientation of lugs.

Step 7: Attach Side Wall and Roof Support

Fit the Side wall (with Vent covers) to the base and side wall. Attach the Roof Support to the top center slot (and the slot above it) using six Pi Clips.

Diagram Description: Shows the side wall with vent covers being attached, and the roof support being secured to the top of the structure with Pi Clips.

Step 8: Attach Front Wall

Fit the Front Wall (patterned face outermost) to the end with the double-hole lugs using Pi Clips.

Diagram Description: Depicts the front wall being attached to the main structure using Pi Clips.

Step 9: Attach Upper Back Wall

Fit the Upper Back Wall to the top two lugs using two Pi Clips. This step is the same for large, medium, and small models.

Diagram Description: Shows the upper back wall being attached to the top lugs with Pi Clips.

Step 10: Attach Back Door Handles

Fit the Back Door Handles to the textured side of the back door using two Pi Clips per handle. The hook on the handle indicates the top.

Diagram Description: Illustrates attaching the back door handles to the back door using Pi Clips, with the hook orientation shown.

Step 11: Fit Back Door

Fit the Back Door using two Lynch Pins. Rest the bottom of the Back Door in the base slots, push the door onto the lugs, slide the Back Door Handles downwards, and secure with Lynch Pins. Remember the Lynch Pin warning about fingers.

Diagram Description: Shows the back door being fitted using Lynch Pins, with arrows indicating the sequence of actions.

Step 12: Insert Perches

Slide the Perches through the Left and Right Side Walls and secure them with Lynch Pins at both ends.

Diagram Description: Depicts perches being slid through the side walls and secured with Lynch Pins.

Step 13: Assemble Nest Box Walls and Divider

Fit the two Nest box End Walls and the Nest Box Divider to the Nest Box Floor. Then add the Nest Box Front Wall, using a total of twelve Pi Clips.

Diagram Description: Shows the nest box floor with end walls and divider being assembled, followed by the front wall, using Pi Clips.

Step 14: Attach Nest Box to House

Insert the L-lugs of the nest box into the lower holes on the Right Side Wall. Tilt the nest box to push the three upper lugs through their holes, then secure them inside the main house with three Lynch Pins.

Diagram Description: Illustrates how to connect the assembled nest box unit to the main house structure using L-lugs and securing with Lynch Pins.

Step 15: Fit Nest Box Lid Braces

Fit the Nest box Front Brace and the two Nest box Side Braces to the Nest box Lid. Ensure the patterned side of the lid faces upwards. Use seven Pi Clips.

Diagram Description: Shows the nest box lid with its braces being attached using Pi Clips.

Step 16: Attach Nest Box Lid

The Nest Box Lid slides upwards, fitting cutouts into recesses in the vertical panels. Secure it with two Lynch Pins.

Diagram Description: Depicts the nest box lid sliding into place and being secured with Lynch Pins.

Step 17: Attach Side Roof Retainers

Fit two Side Roof Retainers, one on each side wall, using one Pi Clip for each.

Diagram Description: Shows side roof retainers being attached to the side walls with Pi Clips.

Step 18: Attach End Roof Retainers

Fit End Roof Retainers to the Front Wall and Upper Back Wall using one Pi Clip for each.

Diagram Description: Shows end roof retainers being attached to the front and upper back walls with Pi Clips.

Step 19: Fit Roof

Fit the Roof using Lynch Pins. Start by fixing the center, then bend the sides over the remaining lugs.

Diagram Description: Illustrates fitting the roof, starting from the center and securing the sides with Lynch Pins.

Step 20: Manual Door Cord Setup

For manual doors: Tie one end of the Cord to the Split Ring in the Front Door and the other end to the small hole in the Door Handle. The cord should pass through the handle slot. Adjust the cord length so the handle hooks onto the opposite handhold or roof edge when the door is fully raised.

Diagram Description: Shows the cord being attached to the front door's split ring and the door handle, with an arrow indicating the cord path through the handle slot.

Step 21: Fit Ramp

Fit the Ramp onto the two lugs (front face) using two 25mm Clevis Pins and two R-Clips. The ramp will tilt to the ground under its own weight.

Diagram Description: Depicts the ramp being attached to the underside of the door area using clevis pins and R-clips. An arrow shows the ramp tilting down.

Diagram Description: A final image shows the "Completed Large House".

Instructions for Use

Siting: Place the chicken house in a sheltered area, with the front facing away from prevailing winds. Adjust vents for good ventilation.

Cleaning & Maintenance: The rear door is useful for inspection and regular cleaning. For thorough cleaning or bedding changes, the entire roof can be removed. Cleaning is recommended at least every 3 months. A pressure washer is ideal, but a hose and scrubbing brush will also work. The plastic is easy to clean. Apply "Poultry Shield" (or similar) and let dry. For red mite protection, sprinkle diatomaceous earth around the house, especially in joints, during bedding changes.

Moving: The house is designed for two people to move, using the handholds cut into the roof.

Accessories for your Chicken Coop

Automatic Door Opener: The Nestera automatic door opener attaches to the front of the coop, allowing timed opening and closing based on your schedule.

Droppings Trays: If using shavings as bedding, droppings trays are recommended to keep shavings dry and simplify cleaning by allowing easy removal and disposal.