VEVOR LIFT TABLE CART USER MANUAL

Need Help? Contact Us!

For product questions or technical support, please contact:

Technical Support and E-Warranty Certificate
www.vevor.com/support

Product Illustration

A detailed illustration of the VEVOR Lift Table Cart. It features a robust metal frame with a scissor-lift mechanism. The base has four wheels for mobility, and the top platform is designed to hold heavy loads. A motor and hydraulic components are visible beneath the platform.

Specifications

Remark: Specifications are subject to change without prior notice.

⚠️ WARNING!

• Do not touch the power plug with wet hands.
• Do not damage the power plug and power cord.
• Do not use if the power plug or power cord is damaged.
• Do not pull the power cord to unplug the power plug.
• Do not use loose sockets.
• Please do not disassemble the product without authorization to avoid failure and affect its use.
• Do not place flammable and explosive materials, such as fuel spray.
• It is necessary to use an independent power socket with a grounding wire and ensure that the power circuit is reliably grounded.

⚠️ WARNING! (Continued)

• When maintaining and cleaning the machine, the power plug must be unplugged.
• Do not allow children to operate alone: the electric lift platform may pose a safety hazard. Please ensure that children use it under adult guidance or lower the lift platform to the lowest height when leaving.
• Avoid use in humid environments: do not use an electric lifting platform in a humid environment to avoid electric shock or equipment failure.
• Do not use the electric lifting platform as a toy: it is not a toy; do not use it for unintended purposes to avoid equipment damage or personal injury.
• Emergency measures: In case of equipment failure, abnormal noise, or other emergency situations, please stop using immediately, disconnect the power supply, and seek professional help.

PRECAUTIONS FOR USE

1. Load limitation: The load of the electric lifting platform should be strictly controlled within the rated range to avoid overload. At the same time, ensure that it is used on a flat ground to avoid partial load causing the equipment to tip over.
2. Smooth start and stop: The electric lifting platform should be kept stable when starting and stopping, to avoid sudden braking and sudden start. Observe the running status of the device at any time during operation. If there is an anomaly, stop the machine immediately for inspection.
3. Prevent collision: During the operation of the electric lifting platform, the surrounding environment should be ensured to avoid collision with walls, obstacles, etc. When approaching the target height, slow down in advance to ensure a smooth stop.
4. Regular maintenance: After the electric lifting platform is used for a period of time, regular maintenance should be carried out to check for damage to worn parts and replace damaged parts in time to ensure the normal operation of the equipment.

PRECAUTIONS FOR USE (Continued)

5. Safety training: Safety training for electric lifting platform operators is essential to understand operating principles and precautions to master correct operation methods.
6. Distress measures: In the event of an emergency, correct emergency measures should be taken, such as distress stop or emergency power cut off, to ensure the safety of personnel and equipment.
7. Remote battery: The remote control battery needs to be purchased separately. The applicable model is 23A/12V, and the size is 28 mm X 10 mm.

Operation Introduction

1. Connect power cables as shown in the figure:

Diagrams show the process of connecting power cables. The first image illustrates a standard electrical plug being inserted into a wall socket. The second image provides a closer view of the plug and socket connection. The third image shows the power cord being connected to the lift table unit.

Diagram illustrating the connection of the cable remote control. The first image depicts the connector end of the remote cable being inserted into its corresponding port on the lift unit. The second image shows the secured connection, with an arrow indicating a rotational lock or secure fit.

2. Press the up/down key. The electric lift platform will run.

Sequence of diagrams illustrating the operation of the electric lift platform. Image 1 shows the wired controller with two buttons (rise/fall) and the remote control with three buttons (up/down/stop). A note states: "The electric lifting platform can be stopped at any height." Image 2 shows the lift platform in a raised position. Image 3 shows the lift platform in a lowered position. Arrows indicate the movement from one state to another.

NOTICE:

• (1) Remote control: Has three buttons: up, down, stop, click operation.
• (2) Wired remote control: Has only 2 buttons: rise and fall. Press and hold the button for the motor to move, and release the button to stop the motor.

3. Accessories have two choices of casters and foot cups, as shown in the figure below, and can be fixed with nuts.

Two diagrams illustrate accessory options for the lift table cart. The left image shows a caster wheel attached to the base of the lift. The right image shows a foot cup (or pad) attached to the base, providing a stable resting point. Both can be secured with nuts.

Product Description

Parts List

Battery specifications required: 23A / 12V, Number: 1

Illustrations of the required 23A/12V battery. The left image shows a single battery with dimensions labeled. The right image shows two such batteries side-by-side, with their lengths and diameters indicated as approximately 28mm and 10mm respectively.

Environmental Information

Note: This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste but must be taken to a collection point for recycling electrical and electronic devices.

♻️ [Recycling Symbol] Wheelie bin crossed out.

Manufacturer and Distributor Information

Manufacturer: Shanghaimuxinmuyeyouxiangongsi
Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EU Representative: E-CrossStu GmbH
Mainzer Landstr.69, 60329 Frankfurt am Main.

UK Representative: YH CONSULTING LIMITED.
C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX