SYLVANIA MOSAIC LED Flexible Light Kit

Package Contents

• 5x 2ft LED Light Strips (with adhesive backs)
• 1x RF Controller
• 1x AC/DC Adapter
• 4x Connectors
• 1x Remote (battery included)
• 6x Mounting Clips (with adhesive backs)

Safety Information

WARNING!

• To avoid electrical shock or product failure, use this strip only in dry indoor environments.
• This product is not a toy and should not be stored or left where young children can access it.
• To prevent possible fire, product damage, or early strip failure, do not use this strip in heat-producing appliances.
• To avoid fire hazards, connect a maximum of 10 strips (totaling 20 feet) to a single AC adapter and Controller.
• To prevent early strip failure, install the strip in operating environments between 14°F to 104°F (-10°C to +40°C).
• Choking Hazard: This kit contains small parts. Keep away from young children and pets.
• Always uncoil the flexible light strip before plugging it in.
• Do not install near flammable liquids.
• Do not install where the strip may be stepped on or be subject to physical damage.
• Always unplug this product before installing, cutting the strip, or connecting to power.
• When connecting additional strips, use only SYLVANIA LED Mosaic RGB+W Flex Kits and connectors.
• Not for use with phase cut dimmers.

CAUTION!

• When not using the product for extended periods, remove the battery from the remote to prevent damage from battery leakage.
• Observe proper polarity when changing the battery. The strip may not light if the battery is inserted incorrectly.
• The included AC/DC adapter (model 65482) is not designed for seasonal use LED drives or non-integral LED lighting strings.

Troubleshooting Remote Connection

If the remote does not connect to the strip's controller, re-pair it using these steps:

1. Turn off the power for approximately 5 seconds by disconnecting the power supply from the outlet.
2. Reconnect the power supply to the outlet. Immediately press the ON button on the remote 3 or more times in quick succession.
3. Successful pairing is indicated when the strip lights up green and flashes rapidly a few times. If unsuccessful, repeat the process until the strip is paired.

Setting Up

Please read, follow, and understand this entire manual before attempting to assemble, operate, or install this product. Save these instructions.

1. Once the final mounting position is determined, clean the surface to ensure the self-adhesive backing adheres properly. The mounting surface must be smooth, dry, and free from oils and waxes for correct adhesion. For best results, apply the strip at a room temperature between 68-86°F (20-30°C). The Mosaic strips can be installed on curved and irregular surfaces, but avoid sharp bends to prevent damage to the light strip.
2. Measure the length of the area where the flex strip will be placed. Each flex strip is 2 feet long. If a strip is too long, shorten it by cutting at one of the lines indicated by the [scissors] icon. Connect all elements together and apply power to test the strip before final mounting.
3. Note: Once cut, a section of flex strip cannot be reconnected to other strips or the universal connector.
4. Note: A maximum of 10 strips can be connected for a total length of 20 feet.
5. Use a connector if wrapping the light strip around a corner. Connectors help prevent crimping or permanent damage to the light strip.
6. Remove the protective layer from the back of the flex strip. Carefully place each strip in the final mounting position, as the adhesive is permanent and the strip cannot be easily moved.
7. Press the flex strip firmly in place and hold for 5 seconds to ensure the adhesive bonds to the mounting surface. Make sure each flex strip is tightly connected to the next before continuing.
8. Connect the controller to the flex strip. Ensure the arrow icon on the controller connector matches the '12V+' marking on the connecting strip.
9. Connect the AC/DC Adapter to the controller.
10. Plug the AC/DC Adapter into the power outlet.
11. To turn the strips on, remove the clear pull tab from the remote to allow the battery to make contact. Press the ON button on the remote to light up the strips.

Remote Instructions

Use your flex light remote with the following commands:

• Brightness/frequency down: [arrow-down]
• Brightness/frequency up: [arrow-up]
• Off: [power-symbol]
• On: [power-symbol]
• Red/Green/Blue: [red], [green], [blue]
• White: [white]
• Flash: [flash]
• Strobe: [strobe]
• Other colors: [color-palette]
• Fade: [fade]
• Smooth: [smooth]

Warranty Information

3 YEAR LIMITED WARRANTY: LEDVANCE warrants the Product to be free from defects in materials and workmanship from the date of purchase for the specified warranty period when used as directed. Failure to comply with Product warnings and instructions will void the warranty. This warranty does not cover Product subjected to accident, neglect, abuse, misuse, or acts of God. If the Product fails to operate according to the warranty, return the Product to the place of purchase with proof of purchase date, and LEDVANCE will replace it with the same or a similar Product free of charge. For additional information, contact 1-800 LIGHTBULB (1-800-544-4828) or email: lightbulb@ledvance.com. This is the exclusive remedy available. Liability for incidental or consequential damages is expressly excluded. Some states and jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province.

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.