Olight Perun 3 Rechargeable LED Headlamp User Manual

Product Overview

This manual provides instructions for the Olight Perun 3 rechargeable LED headlamp.

Specifications

Table 1: Performance Data

Table 2: Specifications

• White Light: 3 x Max 9W/LED
• Red Light: Max 1.5W/LED
• CCT: 5700~6700K
• CRI: 70
• Dimensions: (L)116.8*(D)28 mm / (L)4.60*(D)1.10 in
• Weight: 150 g / 5.29 oz (Including Battery)
• Battery: Rechargeable Li-ion Battery 18 Wh (5000 mAh 3.6 V)
• Working Temperature: 0-40°C
• Waterproof: IP68

Included Accessories

• MCC3 Cable
• Headband
• Lanyard
• ETUI

Operating Instructions

1. Preparation

• Remove the insulating film before use (See Figure 1).
• Charging: Use the MCC3 cable (See Figure 2). Charging is complete when the indicator turns green. Full charge takes less than 4 hours.

2. White Light Mode Operations

• Turn On/Off: Single press the switch (See Figure 3). The light will start at the previously selected brightness level (Turbo is memorized as High; High is memorized as Medium if the interval is over 1 minute; SOS is not memorized).
• Lockout Mode: When the flashlight is off, press and hold the switch for about 2 seconds until the flashlight turns off to enable lockout mode. In this mode, a short press and hold (less than 1 second) accesses Moonlight, and releasing exits. To disable lockout mode, press and hold the switch for over 1 second until the light flashes once (See Figure 4).
• Moonlight Mode: When the flashlight is off, press and hold the switch for over one second to access Moonlight. If the last used brightness level was Moonlight, a single press will activate it (See Figure 5).
• Turbo Mode: When the flashlight is on, quickly double press the switch to access Turbo. Repeat to revert to the previous brightness level (if previous was High, it reverts to Medium) (See Figure 6).
• SOS Mode: Quickly press the switch three times or more to enter SOS mode (See Figure 7).
• Change Brightness Level: When the flashlight is on, press and hold the switch to cycle through Low-Medium-High. Release the switch to select a brightness level. Moonlight, Turbo, and SOS modes are not in this cycle (See Figure 8).
• Flashlight Timer: When the flashlight is on, double press and hold the switch to enable the Timer mode. One flash indicates the short timer (3 min), two flashes indicate the long timer (9 min). The flashlight will turn off when the timer expires. Double press and hold again to choose between the two timers. After the first use, the flashlight starts at the last used timer (See Figure 9).
• Proximity Sensor:
  • Turn Off/On: Quickly press the switch 15 times or more (See Figure 10).
  • Functionality: If the lens is covered before or within 0.5 seconds of Turbo activation, the flashlight switches to High. If covered for over 1 minute, it turns off. Removing the obstruction does not return the light to Turbo. This feature is disabled in SOS mode.
  • Temporarily Turn Off: Within 5 seconds after the flashlight switches to High due to proximity detection, quickly double press the switch to return to Turbo and temporarily disable the sensor. Turn off the flashlight to re-enable the sensor (See Figure 11).

3. Red Light Mode Operations

• Access Red Light Mode: When the flashlight is off, double press the switch to access Low red light (See Figure 12).
• Change Brightness Level: When the flashlight is on, double press the switch to choose between High and Low red light (See Figure 13).
• Change Mode: Press and hold the switch to toggle between normal red light and SOS red light (See Figure 14).
• Exit Red Light Mode: When the flashlight is on, single press the switch to turn it off (See Figure 15).

4. Battery Indicator

• When not in Moonlight mode (See Figure 16-1):
  • Green: >60%
  • Orange: 10~60%
  • Red: 5~10%
  • Blinking Red: <5%
• In Moonlight mode (See Figure 16-2):
  • Blinking Red: <5%
  • OFF: >5%

5. Attaching to Headband

• Attach the flashlight to the headband bracket (See Figure 17).

Warranty Information

Olight offers a lifetime warranty in Australia, China, France, Germany, and the USA. For other countries, a 2 or 5-year warranty is provided. The warranty covers defects in material and workmanship under normal use. For complete details, visit Olight.com or your local Olight official website.

Customer Support Contacts:

• Australia: contact@olightstore.com.au
• Austria: kontakt@olightstore.at
• Canada: cs@olightstore.ca
• China: Wechat: olightcs
• France: cs@olightstore.fr
• Germany: kontakt@olightstore.de
• Italy: contatto@olightstore.it
• Japan: cs@olightstore.jp
• Korea: olightkorea@olight.com
• Spain: contacto@olightstore.es
• Thailand: cs@olightstore.co.th
• UK: contact@olightstore.uk
• USA: cs@olightstore.com
• Global: contact@olight.com

Compliance Information

EU Declaration of Conformity: Dongguan Olight E-Commerce Technology Co,Ltd declares that the equipment [Perun 3] complies with Directive 2014/30/EU and RoHS Directive 2011/65/EU & (EU) 2015/863. Full text available at: https://www.olight.com/download

WEEE Disposal and Recycling Information: Dispose of waste equipment at designated collection points for WEEE recycling.

ISED Notice: This device complies with Industry Canada’s ICES standard(s). Operation is subject to two conditions: (1) no interference, and (2) acceptance of any interference. Complies with Canadian ICES-005 Class B.

FCC Compliance Statement: This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) no harmful interference, and (2) acceptance of any interference received. Changes not expressly approved may void user authority.

Safety Information

• The light source of this luminaire is not replaceable.
• Caution: Do not stare at operating light source.
• Replacement of a battery with an incorrect type can defeat a safeguard.